RACAL-DATACOM ============= EXCALIBUR BRI 2000 Card Type ISDN TA Chipset Unidentified I/O Options Network management port ISDN Transfer Rate 56Kbps x 2/64Kbps x 2 ISDN Protocol T-Link, V.110, V.120 Switch Type 5ESS, DMS100, NI-1 Data Bus Serial +------------------------------------------------------------+ | CONNECTIONS | |------------------------------------------------------------| | Function | Label | Function | Label | |----------------------+--------+--------------------+-------| | Left arrow button | BT1 | ISDN U interface | CN1 | |----------------------+--------+--------------------+-------| | ESC button | BT2 | CMS 400 network | CN2 | | | | management jack | | |----------------------+--------+--------------------+-------| | Right arrow button | BT3 | AC power in | CN3 | |----------------------+--------+--------------------+-------| | 1 button | BT4 | RS-232 or V.35 | CN4 | | | | serial port 2 via | | | | | DB-26 connector | | |----------------------+--------+--------------------+-------| | 2 button | BT5 | RS-232 or V.35 | CN5 | | | | serial port 1 via | | | | | DB-26 connector | | |----------------------+--------+--------------------+-------| | 3 button | BT6 | LCD display | LCD | |------------------------------------------------------------| | Note: Standard RS-232 or V.35 serial port connectors | | are provided on included adapter cables. | +------------------------------------------------------------+ +------------------------------------------------------------+ | USER CONFIGURABLE SETTINGS | |------------------------------------------------------------| | Setting | Label | Position | |----------------------------------------+-------+-----------| | i Factory configured - do not alter | RL/SQ | SQ | +------------------------------------------------------------+ +------------------------------------------------------------+ | SERIAL PORT 1 CONFIGURATION | |------------------------------------------------------------| | JB1 | |------------------------------------------------------------| | RS-232 | V.35 | |------------------------------+-----------------------------| | | [3][IMG] | +------------------------------------------------------------+ +------------------------------------------------------------+ | SERIAL PORT 2 CONFIGURATION | |------------------------------------------------------------| | JB2 | |------------------------------------------------------------| | RS-232 | V.35 | |------------------------------+-----------------------------| | | [5][IMG] | +------------------------------------------------------------+ +------------------------------------------------------------+ | MISCELLANEOUS TECHNICAL NOTES | |------------------------------------------------------------| | To use call bonding, serial port 1 must be used. | | Serial port 2 only supports speeds of 64Kbps. | +------------------------------------------------------------+ +--------------------------------------------------------+ | SUPPORTED STANDARD COMMANDS | |--------------------------------------------------------| | Basic AT Commands | |--------------------------------------------------------| | +++, 'comma', A/ | |--------------------------------------------------------| | A, D, E, H, O, V, X, Z | |--------------------------------------------------------| | &C, &D, &F, &S, &W, &Z | |--------------------------------------------------------| | S-Registers | |--------------------------------------------------------| | S2, S3, S4, S5, S7, S12, S25, S26 | |--------------------------------------------------------| | V.25bis Commands | |--------------------------------------------------------| | CIC, CRN, CRS, DIC, PRN | |--------------------------------------------------------| | Note: See MHI help file for complete information. | +--------------------------------------------------------+ Proprietary AT Command Set +------------------------------------------------------------+ | AUTO-ANSWER | |------------------------------------------------------------| | Type: | Register | |--------------+---------------------------------------------| | Format: | AT [cmds] S0=n [cmds] | |--------------+---------------------------------------------| | Default: | 1 | |--------------+---------------------------------------------| | Range: | 0 - 127 | |--------------+---------------------------------------------| | Unit: | 10 mS | |--------------+---------------------------------------------| | Description: | Sets the amount of time the TA waits before | | | answering an incoming call. | +------------------------------------------------------------+ +------------------------------------------------------------+ | BIT-MAPPED REGISTER S14 | |------------------------------------------------------------| | Format: | AT [cmds] S14=n [cmds] | |--------------+---------------------------------------------| | Default: | 3 | |--------------+---------------------------------------------| | Range: | 0 - 3 | |--------------+---------------------------------------------| | Description: | Controls echo and result code display. | |--------------+---------------------------------------------| | Bit | Value | Function | |------+-------+---------------------------------------------| | 0 | 0 | Command echo disabled. | | | | | | | i 1 | Command echo enabled. | |------+-------+---------------------------------------------| | 1 | 0 | Display result codes in numeric format. | | | | | | | i 1 | Display result codes in verbose format. | +------------------------------------------------------------+ +------------------------------------------------------------+ | BIT-MAPPED REGISTER S21 | |------------------------------------------------------------| | Format: | AT [cmds] S21=n [cmds] | |-----------------+------------------------------------------| | Default: | 2 | |-----------------+------------------------------------------| | Range: | 0 - 27 | |-----------------+------------------------------------------| | Description: | Controls CTS, DCD, and DSR signals. | |------------------------------------------------------------| | Bit | Value | Function | |----------+-------+-----------------------------------------| | 0 | i 0 | CTS follows RTS. | | | | | | | 1 | CTS normal. | |------------------------------------------------------------| | 1 | 0 | DCD forced high. | | | | | | | i | DCD normal. | | | 1 | | |--------------+----+----------------------------------------| | 3, 2 | i | DSR forced high. | | | 00 | | | | | DSR normal. | | | 01 | | | | | DSR forced high if ISDN is active. | | | 10 | | |--------------+----+----------------------------------------| | 4 | i | DSR forced low during all tests. | | | 0 | | | | | DSR forced low only if test pattern is | | | 1 | active. | +------------------------------------------------------------+ +------------------------------------------------------------+ | CALLER ID NUMBER | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] @Zn [cmds] | |--------------+---------------------------------------------| | Description: | Sets the stored number indicated as a | | | Caller ID number for Caller ID security. | +------------------------------------------------------------+ +------------------------------------------------------------+ | CLEAR STORED NUMBERS | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] @N99 [cmds] | |--------------+---------------------------------------------| | Description: | Clears all stored telephone numbers. | +------------------------------------------------------------+ +------------------------------------------------------------+ | CLEAR STORED NUMBERS - CALLER ID | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] &N99 [cmds] | |--------------+---------------------------------------------| | Description: | Clears all stored numbers set for caller | | | ID. | +------------------------------------------------------------+ +------------------------------------------------------------+ | CLOCK SOURCE - RECEIVE | |------------------------------------------------------------| | Type: | Register | |--------------+---------------------------------------------| | Format: | AT [cmds] S35=n [cmds] | |--------------+---------------------------------------------| | Description: | Selects the source for the receive clock. | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | i S34=0 | Receive clock generated from received | | | signal. | |--------------+---------------------------------------------| | S34=1 | Receive clock generated from external | | | source. | +------------------------------------------------------------+ +------------------------------------------------------------+ | CLOCK SOURCE - TRANSMIT | |------------------------------------------------------------| | Type: | Register | |--------------+---------------------------------------------| | Format: | AT [cmds] S34=n [cmds] | |--------------+---------------------------------------------| | Description: | Selects the source for the transmit clock. | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | i S34=0 | Transmit clock generated from received | | | signal. | |--------------+---------------------------------------------| | S34=1 | Transmit clock generated from external | | | source. | +------------------------------------------------------------+ +------------------------------------------------------------+ | COMMUNICATIONS MODE | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] &Qn [cmds] | |--------------+---------------------------------------------| | Description: | Selects whether the TA will operate in | | | synchronous or asynchronous mode. | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | &Q0 | TA will operate in asynchronous mode. | |--------------+---------------------------------------------| | i &Q1 | TA will operate in synchronous mode. | +------------------------------------------------------------+ +------------------------------------------------------------+ | COMMUNICATIONS MODE | |------------------------------------------------------------| | Type: | Register | |--------------+---------------------------------------------| | Format: | AT [cmds] S27=n [cmds] | |--------------+---------------------------------------------| | Description: | Selects whether the TA will operate in | | | synchronous or asynchronous mode. | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | S27=0 | TA will operate in asynchronous mode. | |--------------+---------------------------------------------| | i S27=1 | TA will operate in synchronous mode. | +------------------------------------------------------------+ +------------------------------------------------------------+ | DATA FORMAT | |------------------------------------------------------------| | Format: | AT [cmds] S23=n [cmds] | |-----------------+------------------------------------------| | Default: | 0 | |-----------------+------------------------------------------| | Range: | 0 - 14 | |-----------------+------------------------------------------| | Description: | Controls the number of data and stop | | | bits. | |------------------------------------------------------------| | Bit | Value | Function | |---------+---------------+----------------------------------| | 0 | 0 | Not used. | |------------------------------------------------------------| | 1 | i 0 | One stop bit. | | | | | | | 1 | Two stop bits. | |-------------+--------------------+-------------------------| | 3, 2 | i 00 | Eight data bits. | | | | | | | 01 | Seven data bits. | | | | | | | 10 | Six data bits. | | | | | | | 11 | Five data bits. | +------------------------------------------------------------+ +------------------------------------------------------------+ | DATA TYPE - B1 CHANNEL | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] \C1=n [cmds] | |--------------+---------------------------------------------| | Description: | Sets the format for data being sent over | | | the B1 channel. | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | \C1=0 | B1 channel carries standard data. | |--------------+---------------------------------------------| | i \C1=1 | B1 channel carries circuit-switched data. | +------------------------------------------------------------+ +------------------------------------------------------------+ | DATA TYPE - B2 CHANNEL | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] \C2=n [cmds] | |--------------+---------------------------------------------| | Description: | Sets the format for data being sent over | | | the B2 channel. | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | \C2=0 | B2 channel carries standard data. | |--------------+---------------------------------------------| | i \C2=1 | B2 channel carries circuit-switched data. | +------------------------------------------------------------+ +------------------------------------------------------------+ | DIRECTORY NUMBER 1 | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] !N1=<#> [cmds] | |--------------+---------------------------------------------| | Description: | Sets the first Directory Number to the | | | number indicated. | +------------------------------------------------------------+ +------------------------------------------------------------+ | DIRECTORY NUMBER 2 | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] !N2=<#> [cmds] | |--------------+---------------------------------------------| | Description: | Sets the second Directory Number to the | | | number indicated. | +------------------------------------------------------------+ +------------------------------------------------------------+ | DISPLAY CONFIGURATION | |------------------------------------------------------------| | Type: | Immediate | |--------------+---------------------------------------------| | Format: | AT [cmds] &Vn [cmds] | |--------------+---------------------------------------------| | Description: | Displays the indicated part of the TA's | | | configuration. | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | &V0 | Displays the command setting for the port. | |--------------+---------------------------------------------| | &V1 | Displays all stored telephone numbers. | +------------------------------------------------------------+ +------------------------------------------------------------+ | DISPLAY INFORMATION | |------------------------------------------------------------| | Type: | Immediate | |--------------+---------------------------------------------| | Format: | AT [cmds] In [cmds] | |--------------+---------------------------------------------| | Description: | Displays information requested about the | | | TA. | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | I0 | Displays product identification code. | |--------------+---------------------------------------------| | I1 | Displays ROM checksum. | |--------------+---------------------------------------------| | I2 | Tests and displays ROM checksum result. | |--------------+---------------------------------------------| | I3 | Displays firmware part number, revision, | | | and checksum. | +------------------------------------------------------------+ +------------------------------------------------------------+ | DTR SIGNAL | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] \Dn [cmds] | |--------------+---------------------------------------------| | Description: | Controls the operation of the DTR signal. | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | i \D0 | DTR normal. | |--------------+---------------------------------------------| | \D1 | DTR forced high. | +------------------------------------------------------------+ +------------------------------------------------------------+ | DTR SIGNAL | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] S33=n [cmds] | |--------------+---------------------------------------------| | Description: | Controls the operation of the DTR signal. | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | i S33=0 | DTR normal. | |--------------+---------------------------------------------| | S33=1 | DTR forced high. | +------------------------------------------------------------+ +------------------------------------------------------------+ | FRONT PANEL CONTROLS | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] @Fn [cmds] | |--------------+---------------------------------------------| | Description: | Select whether the front panel controls are | | | operative. | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | @F0 | Front panel controls disabled. | |--------------+---------------------------------------------| | i @F1 | Front panel controls enabled. | +------------------------------------------------------------+ +------------------------------------------------------------+ | LINE SPEED - B1 CHANNEL | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] \B1=n [cmds] | |--------------+---------------------------------------------| | Description: | Sets the line speed of the B1 channel. | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | \B1=0 | B1 channel speed set to 56Kbps. | |--------------+---------------------------------------------| | i \B1=1 | B1 channel speed set to 64Kbps. | +------------------------------------------------------------+ +------------------------------------------------------------+ | LINE SPEED - B2 CHANNEL | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] \B2=n [cmds] | |--------------+---------------------------------------------| | Description: | Sets the line speed of the B2 channel. | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | \B2=0 | B2 channel speed set to 56Kbps. | |--------------+---------------------------------------------| | i \B2=1 | B2 channel speed set to 64Kbps. | +------------------------------------------------------------+ +------------------------------------------------------------+ | LOCAL SERIAL PORT SPEED | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] Fn [cmds] | |--------------+---------------------------------------------| | Description: | Sets the speed of the local serial port. | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | F0 | Serial port speed set to 300bps. | |--------------+---------------------------------------------| | F1 | Serial port speed set to 600bps. | |--------------+---------------------------------------------| | F2 | Serial port speed set to 1200bps. | |--------------+---------------------------------------------| | F3 | Serial port speed set to 2400bps. | |--------------+---------------------------------------------| | F4 | Serial port speed set to 4800bps. | |--------------+---------------------------------------------| | F5 | Serial port speed set to 7200bps. | |--------------+---------------------------------------------| | F6 | Serial port speed set to 9600bps. | |--------------+---------------------------------------------| | F7 | Serial port speed set to 14.4Kbps. | |--------------+---------------------------------------------| | F8 | Serial port speed set to 19.2Kbps. | |--------------+---------------------------------------------| | F9 | Serial port speed set to 38.4Kbps. | |--------------+---------------------------------------------| | F12 | Serial port speed set to 57.6Kbps. | +------------------------------------------------------------+ +------------------------------------------------------------+ | LOCAL SERIAL PORT SPEED | |------------------------------------------------------------| | Type: | Register | |--------------+---------------------------------------------| | S29=ormat: | AT [cmds] S29=n [cmds] | |--------------+---------------------------------------------| | Description: | Sets the speed of the local serial port. | |--------------+---------------------------------------------| | Command | S29=unction | |--------------+---------------------------------------------| | S29=0 | Serial port speed set to 300bps. | |--------------+---------------------------------------------| | S29=1 | Serial port speed set to 600bps. | |--------------+---------------------------------------------| | S29=2 | Serial port speed set to 1200bps. | |--------------+---------------------------------------------| | S29=3 | Serial port speed set to 2400bps. | |--------------+---------------------------------------------| | S29=4 | Serial port speed set to 4800bps. | |--------------+---------------------------------------------| | S29=5 | Serial port speed set to 7200bps. | |--------------+---------------------------------------------| | S29=6 | Serial port speed set to 9600bps. | |--------------+---------------------------------------------| | S29=7 | Serial port speed set to 14.4Kbps. | |--------------+---------------------------------------------| | S29=8 | Serial port speed set to 19.2Kbps. | |--------------+---------------------------------------------| | S29=9 | Serial port speed set to 38.4Kbps. | |--------------+---------------------------------------------| | S29=12 | Serial port speed set to 57.6Kbps. | +------------------------------------------------------------+ +------------------------------------------------------------+ | NETWORK MANAGEMENT ADDRESS | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] @CMSA=n [cmds] | |--------------+---------------------------------------------| | Default: | Unidentified | |--------------+---------------------------------------------| | Range: | 1 - 255 | |--------------+---------------------------------------------| | Unit: | N/A | |--------------+---------------------------------------------| | Description: | Sets the CMS network management address for | | | the TA. | +------------------------------------------------------------+ +------------------------------------------------------------+ | NETWORK MANAGEMENT SPEED | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] @CMSFn [cmds] | |--------------+---------------------------------------------| | Description: | Sets the speed of the CMS network | | | management port. | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | i @CMSF0 | Set network management port speed to 75bps. | |--------------+---------------------------------------------| | @CMSF1 | Set network management port speed to | | | 300bps. | |--------------+---------------------------------------------| | @CMSF2 | Set network management port speed to | | | 1200bps. | |--------------+---------------------------------------------| | @CMSF3 | Set network management port speed to | | | 2400bps. | |--------------+---------------------------------------------| | @CMSF4 | Set network management port speed to | | | 4800bps. | |--------------+---------------------------------------------| | @CMSF5 | Set network management port speed to | | | 9600bps. | |--------------+---------------------------------------------| | @CMSF6 | Set network management port speed to | | | 19.2Kbps. | +------------------------------------------------------------+ +------------------------------------------------------------+ | NETWORK MANAGEMENT TYPE | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] @CMSNn [cmds] | |--------------+---------------------------------------------| | Description: | Sets where the TA is in respect to the CMS | | | network management unit. | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | @CMSN0 | TA is local to the network management unit. | |--------------+---------------------------------------------| | i @CMSN1 | TA is remote from the network management | | | unit. | +------------------------------------------------------------+ +------------------------------------------------------------+ | POWER FAIL ALARM DELAY | |------------------------------------------------------------| | Type: | Register | |--------------+---------------------------------------------| | Format: | AT [cmds] S30=n [cmds] | |--------------+---------------------------------------------| | Default: | 10 | |--------------+---------------------------------------------| | Range: | 0 - 127 | |--------------+---------------------------------------------| | Unit: | 1 second | |--------------+---------------------------------------------| | Description: | Sets the amount of time the TA waits after | | | the DTE loses power before generating an | | | alarm condition. | +------------------------------------------------------------+ +------------------------------------------------------------+ | PROTOCOL - RATE ADAPTATION | |------------------------------------------------------------| | Type: | Register | |--------------+---------------------------------------------| | Format: | AT [cmds] S28=n [cmds] | |--------------+---------------------------------------------| | Description: | Selects the rate adaptation protocol the TA | | | will use. | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | i S28=0 | TA will use V.120 for rate adaptation. | |--------------+---------------------------------------------| | S28=1 | TA will use T-Link for rate adaptation. | +------------------------------------------------------------+ +------------------------------------------------------------+ | REDIAL DELAY | |------------------------------------------------------------| | Type: | Register | |--------------+---------------------------------------------| | Format: | AT [cmds] S44=n [cmds] | |--------------+---------------------------------------------| | Default: | 30 | |--------------+---------------------------------------------| | Range: | 0 - 127 | |--------------+---------------------------------------------| | Unit: | .5 second | |--------------+---------------------------------------------| | Description: | Sets the amount of time the TA will wait | | | before redialing a call that did not | | | connect. | +------------------------------------------------------------+ +------------------------------------------------------------+ | RESULT CODES | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] Qn [cmds] | |--------------+---------------------------------------------| | Description: | Enables TA to send result codes to the DTE. | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | i Q0 | Result codes enabled. | |--------------+---------------------------------------------| | Q1 | Result codes disabled. | |--------------+---------------------------------------------| | Q2 | Result codes enabled in originate mode | | | only. | +------------------------------------------------------------+ +------------------------------------------------------------+ | RTS SIGNAL | |------------------------------------------------------------| | Type: | Register | |--------------+---------------------------------------------| | Format: | AT [cmds] S32=n [cmds] | |--------------+---------------------------------------------| | Description: | Controls the operation of the RTS signal. | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | S32=0 | RTS forced high. | |--------------+---------------------------------------------| | i S32=1 | RTS normal. | +------------------------------------------------------------+ +------------------------------------------------------------+ | SECURITY | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] @Cn [cmds] | |--------------+---------------------------------------------| | Description: | Selects what type of security will be used | | | for dial-in. | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | i @C0 | Security disabled. | |--------------+---------------------------------------------| | @C1 | Caller ID security enabled. | |--------------+---------------------------------------------| | @C2 | Password security enabled. | +------------------------------------------------------------+ +------------------------------------------------------------+ | SECURITY | |------------------------------------------------------------| | Type: | Register | |--------------+---------------------------------------------| | Format: | AT [cmds] S42=n [cmds] | |--------------+---------------------------------------------| | Description: | Selects what type of security will be used | | | for dial-in. | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | i S42=0 | Security disabled. | |--------------+---------------------------------------------| | S42=1 | Caller ID security enabled. | |--------------+---------------------------------------------| | S42=2 | Password security enabled. | +------------------------------------------------------------+ +------------------------------------------------------------+ | SPID 1 | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] \SP1=<#> [cmds] | |--------------+---------------------------------------------| | Description: | Sets the first Service Profile ID to the | | | number indicated. | +------------------------------------------------------------+ +------------------------------------------------------------+ | SPID 2 | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] \SP2=<#> [cmds] | |--------------+---------------------------------------------| | Description: | Sets the second Service Profile ID to the | | | number indicated. | +------------------------------------------------------------+ +------------------------------------------------------------+ | SPID DISABLE | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] \SP0 [cmds] | |--------------+---------------------------------------------| | Description: | Disables both Service Profile ID's. | +------------------------------------------------------------+ +------------------------------------------------------------+ | SWITCH TYPE | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] \Sn [cmds] | |--------------+---------------------------------------------| | Description: | Sets the type of switch the TA is connected | | | to. | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | \S0 | TA is connected to AT&T 5ESS switch. | |--------------+---------------------------------------------| | \S1 | TA is connected to DMS-100 switch. | |--------------+---------------------------------------------| | \S2 | TA is connected to National NI-1 switch. | +------------------------------------------------------------+ Proprietary V.25bis Command Set +------------------------------------------------------------+ | REQUEST LISTED NUMBERS | |------------------------------------------------------------| | Type: | Immediate | |--------------+---------------------------------------------| | Format: | RLN | |--------------+---------------------------------------------| | Description: | Requests the modem to return the list of | | | stored numbers. | +------------------------------------------------------------+