PIICEON, INC. ============= DISPATCHER 805-3400 Card Type Modem (asynchronous) Chipset Rockwell Maximum Data Rate 28.8Kbps Maximum Fax Rate 14.4Kbps Data Bus Compaq communications bus Fax Class Class I & II Data Modulation Bell 103A/212A ITU-T V.21, V.22, V.23, V.22bis, V.32, V.32bis, V.34 Fax Modulation ITU-T V.17, V.21CH2, V.27ter, V.29 Error MNP5, MNP10, V.42, V.42bis Correction/Compression +------------------------------------------------------------+ | CONNECTIONS | |------------------------------------------------------------| | Function | Label | Function | Label | |------------------------------------------------------------| | Line out | CN1 | Compaq communications bus | CN3 | |---------------+----------+---------------------------+-----| | Line in | CN2 | | | +------------------------------------------------------------+ +------------------------------------------------------------+ | SUPPORTED STANDARD COMMANDS | |------------------------------------------------------------| | Basic AT Commands | |------------------------------------------------------------| | +++, 'comma', A/ | |------------------------------------------------------------| | A, B, C, E, H, L, M, N, O, Q, V, W, X, Y, Z | |------------------------------------------------------------| | &C, &D, &F, &G, &K, &L, &M, &P, &Q, &R, &S, &T, &V, &W, | | &Y, &Z | |------------------------------------------------------------| | Extended AT Commands | |------------------------------------------------------------| | \A, \B, \G, \J, \L, \W | |------------------------------------------------------------| | %C, %F, %L, %Q | |------------------------------------------------------------| | S-Registers | |------------------------------------------------------------| | S0, S1, S2, S3, S4, S5, S6, S7, S8, S9, S10, S12, S14, | | S16, S18, S21, S22, S23, S24, S25, S27, | |------------------------------------------------------------| | S28, S29, S30, S31, S32, S33, S36, S38, S39, S40, S41, | | S46, S48, S82, S86, S91, S92, S95, S201 | |------------------------------------------------------------| | Special AT Commands | |------------------------------------------------------------| | -K, -Q, *H, )M, @M, :E, #CID | |------------------------------------------------------------| | Note: See MHI help file for full command | | documentation. | +------------------------------------------------------------+ Proprietary AT Command Set +------------------------------------------------------------+ | BREAK TYPE | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] \Kn [cmds] | |--------------+---------------------------------------------| | Description: | Configures action of break signal | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | \K0 | Online command mode enabled, do not send | | | break to remote modem. | |--------------+---------------------------------------------| | \K1 | Break sent to remote modem and buffered | | | cleared. | |--------------+---------------------------------------------| | \K2 | Online command mode enabled, do not send | | | break to remote modem. | |--------------+---------------------------------------------| | \K3 | Send break to remote modem immediately. | |--------------+---------------------------------------------| | \K4 | Online command mode enabled, do not send | | | break to remote modem. | |--------------+---------------------------------------------| | i \K5 | Send break with transmitted data. | +------------------------------------------------------------+ +------------------------------------------------------------+ | CALLBACK | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] *Pn:xxxx:<#> | |--------------+---------------------------------------------| | Description: | Stores the information for callback number | | | n. When enabled, the modem will call back | | | the phone number indicated and request the | | | matching password. | +------------------------------------------------------------+ +------------------------------------------------------------+ | CELLULAR DRIVER DOWNLOAD | |------------------------------------------------------------| | Type: | Immediate | |--------------+---------------------------------------------| | Format: | AT [cmds] ^C2 | |--------------+---------------------------------------------| | Description: | Initiates an ASCII transfer of a new | | | cellular phone driver. | +------------------------------------------------------------+ +------------------------------------------------------------+ | CELLULAR DRIVER INFORMATION | |------------------------------------------------------------| | Type: | Immediate | |--------------+---------------------------------------------| | Format: | AT [cmds] ^I [cmds] | |--------------+---------------------------------------------| | Description: | Displays information about the currently | | | loaded cellular phone driver. | +------------------------------------------------------------+ +------------------------------------------------------------+ | CELLULAR PHONE STATUS | |------------------------------------------------------------| | Type: | Immediate | |------------------------------------------------------------| | Format: | AT [cmds] ^T6 [cmds] | |-----------------+------------------------------------------| | Description: | Displays the current status of the | | | connected cellular phone. | |------------------------------------------------------------| | Bit | Value | Function | |-----------+--------+---------------------------------------| | 0 | 0 | Cellular phone is not receiving an | | | | incoming call. | | | 1 | | | | | Cellular phone is receiving an | | | | incoming call. | |-----------+--------+---------------------------------------| | 1 | 0 | Cellular phone is not in use. | | | | | | | 1 | Cellular phone is in use. | |-----------+--------+---------------------------------------| | 2 | 0 | Cellular phone is not locked. | | | | | | | 1 | Cellular phone is locked. | |-----------+--------+---------------------------------------| | 3 | 0 | Cellular service present. | | | | | | | 1 | Cellular service not present. | |-----------+--------+---------------------------------------| | 4 | 0 | Cellular phone is off. | | | | | | | 1 | Cellular phone is on. | |-----------+--------+---------------------------------------| | 5 | 0 | Cellular driver is not initialized. | | | | | | | 1 | Cellular driver is initialized. | |-----------+--------+---------------------------------------| | 6 | 0 | Not used. | |-----------+--------+---------------------------------------| | 7 | 0 | Cellular cable not detected. | | | | | | | 1 | Cellular cable detected. | +------------------------------------------------------------+ +------------------------------------------------------------+ | CONNECT MODE | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] \Nn [cmds] | |--------------+---------------------------------------------| | Description: | Controls the type of connection the modem | | | will connect with. | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | \N0 | Modem will connect in normal mode. | |--------------+---------------------------------------------| | \N1 | Modem will connect in normal mode. | |--------------+---------------------------------------------| | \N2 | Modem will attempt V.42bis mode, then MNP | | | mode, then hang up. | |--------------+---------------------------------------------| | i \N3 | Modem will attempt V.42bis mode, then MNP | | | mode, then normal mode. | |--------------+---------------------------------------------| | \N4 | Modem will attempt V.42bis mode, then hang | | | up. | |--------------+---------------------------------------------| | \N5 | Modem will attempt MNP mode, then hang up. | +------------------------------------------------------------+ +------------------------------------------------------------+ | DIAL | |------------------------------------------------------------| | Type: | Immediate | |--------------+---------------------------------------------| | Format: | AT [cmds] D<#> [cmds] | |--------------+---------------------------------------------| | Description: | Dials telephone number according to any | | | modifiers included in the string. | |--------------+---------------------------------------------| | Note: | Any combination of modifiers can be used to | | | produce the desired dial functions in | | | sequence. | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | DJ | MNP10 link will be negotiated at 1200bps | | | for this call. | |--------------+---------------------------------------------| | DK | MNP10 power level adjustment enabled for | | | this call. | |--------------+---------------------------------------------| | DL | Re-dial last number. | |--------------+---------------------------------------------| | DP | Dial following digits in pulse mode. | |--------------+---------------------------------------------| | DS=n | Dial stored telephone number n. | |--------------+---------------------------------------------| | DT | Dial following digits in tone mode. | |--------------+---------------------------------------------| | DW | Dialing resumed following dial tone | | | detection. | |--------------+---------------------------------------------| | D, | Dialing paused for amount of time specified | | | in S8 register. | |--------------+---------------------------------------------| | D"WXY" | Optional method of denoting telephone | | | numbers. Letters enclosed in quotes are | | | interpreted as numbers according to the | | | system found on a telephone keypad. | |--------------+---------------------------------------------| | D! | Flash function initiated. Modem commanded | | | to go off-hook for specified time before | | | returning on-hook. | |--------------+---------------------------------------------| | D@ | Wait for Quiet Answer function enabled. | | | Modem waits until a "quiet answer," a | | | ring-back signal followed by silence up to | | | the time specified in S7, is received prior | | | to executing the rest of the dial string. | |--------------+---------------------------------------------| | D& | Wait for AT&T credit card ("bong") tone | | | detection function enabled. Waits for bong | | | tone for amount of time specified by the S7 | | | command. | |--------------+---------------------------------------------| | D$ | Wait for prompt tone detection function | | | enabled. Waits for prompt tone for amount | | | of time specified by the S7 command. | |--------------+---------------------------------------------| | D^ | Toggles calling tone on or off for this | | | call. | |--------------+---------------------------------------------| | D> | Sends grounding pulse on EARTH relay line. | |--------------+---------------------------------------------| | D; | Modem returned to idle state after dialing. | | | The semicolon can only be placed at the end | | | of the dial command. | +------------------------------------------------------------+ +------------------------------------------------------------+ | DISPLAY STORED NUMBERS | |------------------------------------------------------------| | Type: | Immediate | |--------------+---------------------------------------------| | Format: | AT [cmds] \F [cmds] | |--------------+---------------------------------------------| | Description: | Displays all stored numbers. | +------------------------------------------------------------+ +------------------------------------------------------------+ | MODULATION SELECTION | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] +DMS=x,y,z,a [cmds] | |--------------+---------------------------------------------| | Description: | Sets options for active protocol; the | | | transfer rates specified by z and a must be | | | valid for the protocol selected. | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | x=0 | Set protocol to V.21. | |--------------+---------------------------------------------| | x=1 | Set protocol to V.22. | |--------------+---------------------------------------------| | x=2 | Set protocol to V.22bis. | |--------------+---------------------------------------------| | x=3 | Set protocol to V.23. | |--------------+---------------------------------------------| | x=9 | Set protocol to V.32. | |--------------+---------------------------------------------| | x=10 | Set protocol to V.32bis. | |--------------+---------------------------------------------| | x=11 | Set protocol to V.34. | |--------------+---------------------------------------------| | x=64 | Set protocol to Bell 103. | |--------------+---------------------------------------------| | x=69 | Set protocol to Bell 212A. | |--------------+---------------------------------------------| | y=0 | Automode disabled. | |--------------+---------------------------------------------| | y=1 | Auto-detect highest speed enabled | |--------------+---------------------------------------------| | y=2 | Unidentified. | |--------------+---------------------------------------------| | z, a=300 | Set minimum or maximum transfer rate at | | | 300bps, respectively. | |--------------+---------------------------------------------| | z, a=1200 | Set minimum or maximum transfer rate at | | | 1200bps, respectively. | |--------------+---------------------------------------------| | z, a=2400 | Set minimum or maximum transfer rate at | | | 2400bps, respectively. | |--------------+---------------------------------------------| | z, a=4800 | Set minimum or maximum transfer rate at | | | 4800bps, respectively. | |--------------+---------------------------------------------| | z, a=7200 | Set minimum or maximum transfer rate at | | | 7200bps, respectively. | |--------------+---------------------------------------------| | z, a=9600 | Set minimum or maximum transfer rate at | | | 9600bps, respectively. | |--------------+---------------------------------------------| | z, a=12000 | Set minimum or maximum transfer rate at | | | 12000bps, respectively. | |--------------+---------------------------------------------| | z, a=14400 | Set minimum or maximum transfer rate at | | | 14400bps, respectively. | |--------------+---------------------------------------------| | z, a=16800 | Set minimum or maximum transfer rate at | | | 16800bps, respectively. | |--------------+---------------------------------------------| | z, a=19200 | Set minimum or maximum transfer rate at | | | 19200bps, respectively. | |--------------+---------------------------------------------| | z, a=21600 | Set minimum or maximum transfer rate at | | | 21600bps, respectively. | |--------------+---------------------------------------------| | z, a=24000 | Set minimum or maximum transfer rate at | | | 24000bps, respectively. | |--------------+---------------------------------------------| | z, a=26400 | Set minimum or maximum transfer rate at | | | 26400bps, respectively. | |--------------+---------------------------------------------| | z, a=28800 | Set minimum or maximum transfer rate at | | | 28800bps, respectively. | +------------------------------------------------------------+ +------------------------------------------------------------+ | REMOTE CONFIGURATION END | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] *E [cmds] | |--------------+---------------------------------------------| | Description: | Ends the current remote configuration | | | session. | +------------------------------------------------------------+ +------------------------------------------------------------+ | REMOTE CONFIGURATION PASSWORD | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] *Cxxxx [cmds] | |--------------+---------------------------------------------| | Description: | Stores the password that must be sent by a | | | remote modem to enter a remote | | | configuration session on the local modem. | +------------------------------------------------------------+ +------------------------------------------------------------+ | REMOTE CONFIGURATION REQUEST | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] *Rn [cmds] | |--------------+---------------------------------------------| | Description: | Requests the remote modem to start a remote | | | configuration session. | +------------------------------------------------------------+ +------------------------------------------------------------+ | REPORT INFORMATION | |------------------------------------------------------------| | Type: | Immediate | |--------------+---------------------------------------------| | Format: | AT [cmds] In [cmds] | |--------------+---------------------------------------------| | Description: | Displays information requested. | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | I0 | Reports modem model and speed. | |--------------+---------------------------------------------| | I1 | Reports ROM checksum. | |--------------+---------------------------------------------| | I2 | Tests and reports ROM checksum. | |--------------+---------------------------------------------| | I3 | Reports firmware revision. | |--------------+---------------------------------------------| | I4 | Reports OEM identifer. | |--------------+---------------------------------------------| | I5 | Reports country code. | |--------------+---------------------------------------------| | I6 | Reports data pump and ROM revision. | +------------------------------------------------------------+