PUREDATA, LTD. ============== SATISFAXTION MODEM/300 Modem Type Data (asynchronous)/Fax Maximum Data Rate 14.4Kbps Maximum Fax Rate 9600bps Data Bus 8-bit ISA Fax Class Class I Data Modulation Protocol Bell 103A/212A ITU-T V.22, V.22bis, V.32, V.32bis Fax Modulation Protocol ITU-T V.27ter, V.29 Error MNP5, V.42, V.42bis Correction/Compression +------------------------------------------------------------+ | CONNECTIONS | |------------------------------------------------------------| | Purpose | Location | Purpose | Location | |-------------------+----------+------------------+----------| | Line out | CN1 | Line in | CN2 | +------------------------------------------------------------+ +------------------------------------------------------------+ | BASE I/O ADDRESS SELECTION | |------------------------------------------------------------| | Port | SW1/A | SW1/B | |--------------------+-------------------+-------------------| | COM1: (3F8h) | On | On | |--------------------+-------------------+-------------------| |>> COM2: (2F8h) | Off | On | |--------------------+-------------------+-------------------| | COM3: (3E8h) | On | Off | |--------------------+-------------------+-------------------| | COM4: (2E8h) | Off | Off | +------------------------------------------------------------+ +------------------------------------------------------------+ | INTERRUPT SELECTION | |------------------------------------------------------------| | IRQ | SW1/C | SW1/D | SW1/E | SW1/F | |----------+------------+------------+-----------+-----------| | 2 | On | Off | Off | Off | |----------+------------+------------+-----------+-----------| |>> 3 | Off | On | Off | Off | |----------+------------+------------+-----------+-----------| | 4 | Off | Off | On | Off | |----------+------------+------------+-----------+-----------| | 5 | Off | Off | Off | On | +------------------------------------------------------------+ Proprietary AT Command Set +------------------------------------------------------------+ | ACCEPT RELIABLE MODE | |------------------------------------------------------------| | Type: | Immediate | |--------------+---------------------------------------------| | Format: | AT [cmds] \Un | |--------------+---------------------------------------------| | Example: | AT \U | |--------------+---------------------------------------------| | Description: | Accepts remote modem's request for reliable | | | link. | +------------------------------------------------------------+ +------------------------------------------------------------+ | AUTO-RETRAIN - FALLBACK/FALLFORWARD | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] %En [cmds] | |--------------+---------------------------------------------| | Example: | AT %E1 | |--------------+---------------------------------------------| | Description: | Controls auto-retrain mode and | | | fallback/fall forward. | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | %E0 | Auto-retrain disabled. | |--------------+---------------------------------------------| |>> %E1 | Auto-retrain enabled. | |--------------+---------------------------------------------| | %E2 | Fallback/fall forward enabled. | +------------------------------------------------------------+ +------------------------------------------------------------+ | BIT-MAPPED REGISTER S14 | |------------------------------------------------------------| | Format | AT [cmds] S14? [cmds] | |-----------------+------------------------------------------| | Example: | ATS14? | |-----------------+------------------------------------------| | Default: | Read only | |-----------------+------------------------------------------| | Range: | 0-255 | |-----------------+------------------------------------------| | Unit: | Bit-mapped. | |-----------------+------------------------------------------| | Description: | Displays echo, result codes, result code | | | display, dial mode, and answer/originate | | | mode. | |------------------------------------------------------------| | Bit | Value | Function | |----------+------------+------------------------------------| | 0 | 1 | Not used. | |----------+------------+------------------------------------| | 1 | 0 >> 1 | Command echo disabled. | | | | | | | | Command echo enabled. | |----------+------------+------------------------------------| | 2 |>> 0 1 | Result codes enabled. | | | | | | | | Result codes disabled. | |----------+------------+------------------------------------| | 3 | 0 >> 1 | Display result codes in numeric | | | | format. | | | | | | | | Display result codes in verbose | | | | format. | |----------+------------+------------------------------------| | 4 | 0 | Not used. | |----------+------------+------------------------------------| | 5 |>> 0 1 | Tone dial enabled. | | | | | | | | Pulse dial enabled. | |----------+------------+------------------------------------| | 6 | 0 | Not used. | |----------+------------+------------------------------------| | 7 | 0 >> 1 | Answer mode enabled. | | | | | | | | Originate mode enabled. | +------------------------------------------------------------+ +------------------------------------------------------------+ | BIT-MAPPED REGISTER S21 | |------------------------------------------------------------| | Format | AT [cmds] S21? [cmds] | |----------------+-------------------------------------------| | Example: | ATS21? | |----------------+-------------------------------------------| | Default: | Read only | |----------------+-------------------------------------------| | Range: | 0 - 255 | |----------------+-------------------------------------------| | Unit: | Bit-mapped | |----------------+-------------------------------------------| | Description: | Displays low DTR action, DCD signal, DSR | | | signal, and the Long Space Disconnect | | | function. | |------------------------------------------------------------| | Bit | Value | Function | |----------+-------+-----------------------------------------| | 2 - 0 | 010 | Not used. | |----------+-------+-----------------------------------------| | 4, 3 | 00 01 | DTR signal ignored. | | |>> 10 | | | | 11 | Modem goes to command mode on low DTR. | | | | | | | | Modem disconnects on low DTR. | | | | Auto-Answer is disabled. | | | | | | | | Modem is initialized on low DTR. | |----------+-------+-----------------------------------------| | 5 | 0 >> 1 | DCD forced high. | | | | | | | | DCD normal. | |----------+-------+-----------------------------------------| | 6 |>> 0 1 | DSR forced high. | | | | | | | | DSR normal. | |----------+-------+-----------------------------------------| | 7 |>> 0 1 | Long Space Disconnect function | | | | disabled. | | | | | | | | Long Space Disconnect function enabled. | +------------------------------------------------------------+ +------------------------------------------------------------+ | BIT-MAPPED REGISTER S22 | |------------------------------------------------------------| | Format | AT [cmds] S22? [cmds] | |----------------+-------------------------------------------| | Example: | AT S22? | |----------------+-------------------------------------------| | Default: | Read only | |----------------+-------------------------------------------| | Range: | 0 - 255 | |----------------+-------------------------------------------| | Unit: | Bit-mapped. | |----------------+-------------------------------------------| | Description: | Displays volume and speaker settings, | | | result codes, and make/break pulse ratio. | |------------------------------------------------------------| | Bit | Value | Function | |-----------+-------+----------------------------------------| | 1, 0 | 00 01 | Lowest volume setting. | | |>> 10 | | | | 11 | Low volume setting. | | | | | | | | Medium volume setting | | | | | | | | Highest volume setting. | |-----------+-------+----------------------------------------| | 3, 2 | 00 >> | Speaker disabled. | | | 01 10 | | | | 11 | Speaker enabled until carrier signal | | | | detected | | | | | | | | Speaker enabled. | | | | | | | | Speaker enabled following dialing, | | | | then disabled after carrier signal | | | | detected. | |-----------+-------+----------------------------------------| | 6, 5 ,4 | 000 | Busy and dialtone detection disabled, | | | 100 | result codes 0-4 enabled. | | | 101 | | | | 110 >> | Busy and dialtone detection disabled, | | | 111 | result codes 0-5, 10 enabled. | | | | | | | | Busy tone detection disabled, dialtone | | | | detection enabled, result codes 0-6, | | | | 10 enabled. | | | | | | | | Busy tone detection enabled, dialtone | | | | detection disabled, result codes 0-5, | | | | 7, 10 enabled. | | | | | | | | Busy and dialtone detection enabled, | | | | result codes 0-7, 10 enabled. | |-----------+-------+----------------------------------------| | 7 |>> 0 1 | 39/61ms at 10pps (North America) | | | | | | | | 33/67ms at 10pps (Europe) | +------------------------------------------------------------+ +------------------------------------------------------------+ | BIT-MAPPED REGISTER S23 | |------------------------------------------------------------| | Format | AT [cmds] S23? [cmds] | |-----------------+------------------------------------------| | Example: | ATS23? | |-----------------+------------------------------------------| | Default: | Read only | |-----------------+------------------------------------------| | Range: | 0-255 | |-----------------+------------------------------------------| | Unit: | Bit-mapped | |-----------------+------------------------------------------| | Description: | Displays DTE rate and parity. | |------------------------------------------------------------| | Bit | Value | Function | |-----------+---------+--------------------------------------| | 0 | 1 | Not used. | |-----------+---------+--------------------------------------| | 3, 2, 1 | 000 | Sets serial port speed to 0-300bps. | | | | | | | 001 | Sets serial port speed to 600bps. | | | | | | | 010 | Sets serial port speed to 1200bps. | | | | | | | 011 | Sets serial port speed to 2400bps. | | | | | | | 100 | Sets serial port speed to 4800bps. | | | | | | | 101 | Sets serial port speed to 9600bps. | | | | | | | 110 | Sets serial port speed to 19200bps. | | | | | | | 111 | Sets serial port speed to 38400bps. | |-----------+---------+--------------------------------------| | 5,4 |>> 00 10 | Parity even. | | | | | | | | Parity odd. | |-----------+---------+--------------------------------------| | 7, 6 | 0 | Not used. | +------------------------------------------------------------+ +------------------------------------------------------------+ | BIT-MAPPED REGISTER S27 | |------------------------------------------------------------| | Format | AT [cmds] S27? [cmds] | |----------------+-------------------------------------------| | Example: | ATS27? | |----------------+-------------------------------------------| | Default: | Read only | |----------------+-------------------------------------------| | Range: | 0 - 255 | |----------------+-------------------------------------------| | Unit: | Bit-mapped | |----------------+-------------------------------------------| | Description: | Displays protocol type. | |------------------------------------------------------------| | Bit | Value | Function | |----------+-------+-----------------------------------------| | 1 - 0 | 0 | Not used. | |----------+-------+-----------------------------------------| | 5 - 3 | 0 | Not used. | |----------+-------+-----------------------------------------| | 6 | 0 >> 1 | Select CCITT protocols. | | | | | | | | Select Bell protocols. | |----------+-------+-----------------------------------------| | 7, 2 | 0 | Not used. | +------------------------------------------------------------+ +------------------------------------------------------------+ | BREAK SEND | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] \Bn [cmds] | |--------------+---------------------------------------------| | Example: | AT \B3 &W | |--------------+---------------------------------------------| | Default: | 3 | |--------------+---------------------------------------------| | Range: | 1-9 | |--------------+---------------------------------------------| | Unit: | .1 second | |--------------+---------------------------------------------| | Description: | Sends break to modem. | +------------------------------------------------------------+ +------------------------------------------------------------+ | BREAK TYPE | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] \Kn [cmds] | |--------------+---------------------------------------------| | Example: | AT \K1 | |--------------+---------------------------------------------| | Description: | Configures action of break signal. | |------------------------------------------------------------| | Command | Break from | Break from | Modem | | | DTE | remote modem | receives \B | |---------------+--------------+--------------+--------------| | \K0 | Enter | Buffers | Send break | | | command | cleared and | to remote | | | mode, do not | break sent | modem | | | send break | to DTE. | immediately, | | | to remote | | then enter | | | modem. | | command | | | | | mode. | |---------------+--------------+--------------+--------------| | \K1 | Buffers | Buffers | Send break | | | cleared and | cleared and | to remote | | | break sent | break sent | modem | | | to remote | to DTE. | immediately. | | | modem. | | | |---------------+--------------+--------------+--------------| | \K2 | Enter | Send break | Send break | | | command | to DTE | to remote | | | mode, do not | immediately. | modem | | | send break | | immediately, | | | to remote | | then enter | | | modem. | | command | | | | | mode. | |---------------+--------------+--------------+--------------| | \K3 | Send break | Send break | Send break | | | to remote | to DTE | to remote | | | modem | immediately. | modem | | | immediately. | | immediately. | |---------------+--------------+--------------+--------------| | \K4 | Enter | Break sent | Send break | | | command | with | to remote | | | mode, do not | received | modem | | | send break | data to the | immediately, | | | to remote | DTE. | then enter | | | modem. | | command | | | | | mode. | |---------------+--------------+--------------+--------------| |>> \K5 | Send break | Break sent | Send break | | | with | with | to remote | | | transmitted | received | modem | | | data. | data to the | immediately. | | | | DTE. | | +------------------------------------------------------------+ +------------------------------------------------------------+ | COMPRESSION | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT %Cn | |--------------+---------------------------------------------| | Example: | AT *EC0 %C1 *AP0 | |--------------+---------------------------------------------| | Description: | Selects data compression. | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | %C0 | Data compression disabled. | |--------------+---------------------------------------------| |>> %C1 | Data compression enabled. | +------------------------------------------------------------+ +------------------------------------------------------------+ | CONNECT MODE | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] \Nn [cmds] | |--------------+---------------------------------------------| | Example: | AT \N1 DT555-1212 | |--------------+---------------------------------------------| | Description: | Sets connect mode. | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | \N0 | Normal mode enabled. | |--------------+---------------------------------------------| | \N1 | Diagnostic mode, select this before | | | selecting &T commands. | |--------------+---------------------------------------------| | \N2 | Reliable mode enabled. | |--------------+---------------------------------------------| |>> \N3 | Auto-reliable mode enabled. | |--------------+---------------------------------------------| | \N4 | LAPM mode enabled. | +------------------------------------------------------------+ +------------------------------------------------------------+ | CONVERT TO RELIABLE MODE | |------------------------------------------------------------| | Type: | Immediate | |--------------+---------------------------------------------| | Format: | AT [cmds] \Y [cmds] | |--------------+---------------------------------------------| | Example: | AT \Y | |--------------+---------------------------------------------| | Description: | Initiates reliable mode link. | +------------------------------------------------------------+ +------------------------------------------------------------+ | EXTENDED RESULT CODES | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] \Vn [cmds] | |--------------+---------------------------------------------| | Example: | AT \V1 %C1 | |--------------+---------------------------------------------| | Description: | Selects extended result codes. | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | \V0 | Extended result codes disabled. | |--------------+---------------------------------------------| | \V1 | Reliable result codes enabled. | |--------------+---------------------------------------------| |>> \V2 | Error correction and compression result | | | codes enabled. | |--------------+---------------------------------------------| | \V3 | DTE speed result codes enabled. | +------------------------------------------------------------+ +------------------------------------------------------------+ | FLOW CONTROL TYPE | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] \Qn [cmds] | |--------------+---------------------------------------------| | Example: | AT \Q3 A | |--------------+---------------------------------------------| | Description: | Sets type of flow control used by modem. | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | \Q0 | Flow control disabled. | |--------------+---------------------------------------------| | \Q1 | XON/XOFF flow control enabled. | |--------------+---------------------------------------------| |>> \Q3 | RTS/CTS flow control enabled. | +------------------------------------------------------------+ +------------------------------------------------------------+ | INACTIVITY TIMER | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] \Tn [cmds] | |--------------+---------------------------------------------| | Example: | AT\T5 | |--------------+---------------------------------------------| | Default: | 0 | |--------------+---------------------------------------------| | Range: | 0-42 | |--------------+---------------------------------------------| | Unit: | 1 minute | |--------------+---------------------------------------------| | Description: | Sets the length of time that the modem does | | | not receive information before it | | | disconnects. | +------------------------------------------------------------+ +------------------------------------------------------------+ | MAXIMUM BLOCK SIZE FOR TRANSMISSION | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] \An [cmds] | |--------------+---------------------------------------------| | Example: | AT \A3 &MB28800 | |--------------+---------------------------------------------| | Description: | Sets the maximum transmittable block size. | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | \A0 | Maximum MNP block size is 64 characters. | |--------------+---------------------------------------------| | \A1 | Maximum MNP block size is 128 characters. | |--------------+---------------------------------------------| |>> \A2 | Maximum MNP block size is 192 characters. | |--------------+---------------------------------------------| | \A3 | Maximum MNP block size is 256 characters. | +------------------------------------------------------------+ +------------------------------------------------------------+ | ON-LINE IN RELIABLE MODE | |------------------------------------------------------------| | Type: | Immediate | |--------------+---------------------------------------------| | Format: | AT [cmds] \O | |--------------+---------------------------------------------| | Example: | AT \O | |--------------+---------------------------------------------| | Description: | Returns to on-line and requests reliable | | | mode connection. | +------------------------------------------------------------+ +------------------------------------------------------------+ | PROTOCOL/SPEED | |------------------------------------------------------------| | Type: | Register | |--------------+---------------------------------------------| | Format: | AT [cmds] S31=n [cmds] | |--------------+---------------------------------------------| | Example: | AT S31=0 | |--------------+---------------------------------------------| | Description: | Selects the maximum DCE speed. | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| |>> S31=0 | Select last speed at AT command. | |--------------+---------------------------------------------| | S31=3 | Select 300bps speed. | |--------------+---------------------------------------------| | S31=5 | Select 1200bps speed. | |--------------+---------------------------------------------| | S31=6 | Select 2400bps speed. | |--------------+---------------------------------------------| | S31=7 | Select 4800bps speed. | |--------------+---------------------------------------------| | S31=8 | Select 7200bps speed. | |--------------+---------------------------------------------| | S31=9 | Select 9600bps speed. | |--------------+---------------------------------------------| | S31=10 | Select 12Kbps speed. | |--------------+---------------------------------------------| | S31=11 | Select 14.4Kbps speed. | +------------------------------------------------------------+ +------------------------------------------------------------+ | RETURN TO RELIABLE MODE | |------------------------------------------------------------| | Type: | Immediate | |--------------+---------------------------------------------| | Format: | AT [cmds] \Z [cmds] | |--------------+---------------------------------------------| | Example: | AT \Z | |--------------+---------------------------------------------| | Description: | Ends reliable mode link, initiate return to | | | normal mode. | +------------------------------------------------------------+ +------------------------------------------------------------+ | TEST MODES | |------------------------------------------------------------| | Format | AT [cmds] S16=n [cmds] | |----------------+-------------------------------------------| | Example: | ATS16=40 | |----------------+-------------------------------------------| | Default: | 0 | |----------------+-------------------------------------------| | Range: | 0-125 | |----------------+-------------------------------------------| | Unit: | Bit-mapped | |----------------+-------------------------------------------| | Description: | Controls loopback tests, analog, digital, | | | remote digital, and self tests. | |------------------------------------------------------------| | Bit | Value | Function | |----------+--------+----------------------------------------| | 0 |>> 0 1 | Local analog loopback not in progress. | | | | | | | | Local analog loopback in progress. | |----------+--------+----------------------------------------| | 1 |>> 0 | Not used. | |----------+--------+----------------------------------------| | 5 - 1 | 0 | Not used. | |----------+--------+----------------------------------------| | 6 |>> 0 1 | Local analog loopback w/ self-test not | | | | in progress. | | | | | | | | Local analog loopback w/ self-test in | | | | progress. | +------------------------------------------------------------+ +------------------------------------------------------------+ | V.42bis COMPRESSION CONTROL | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] "Hn [cmds] | |--------------+---------------------------------------------| | Example: | AT "H3 &W | |--------------+---------------------------------------------| | Description: | Controls V.42bis data compression | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | "H0 | V.42bis disabled. | |--------------+---------------------------------------------| | "H1 | V.42bis when transmitting enabled. | |--------------+---------------------------------------------| | "H2 | V.42bis when receiving enabled. | |--------------+---------------------------------------------| |>> "H3 | V.42bis when transmitting/receiving | | | enabled. | +------------------------------------------------------------+ +------------------------------------------------------------+ | XON/XOFF PASS-THROUGH | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] \Xn [cmds] | |--------------+---------------------------------------------| | Example: | AT \X1 O | |--------------+---------------------------------------------| | Description: | Selects whether XON/XOFF signals are sent | | | to remote modem. | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| |>> \X0 | XON/XOFF signals trapped by local modem. | |--------------+---------------------------------------------| | \X1 | XON/XOFF passed through local modem. | +------------------------------------------------------------+