MIRO COMPUTER PRODUCTS, INC. ============================ MIROMEDIA ONLINE PNP Card Type Modem/Communication Adapter card Chip Set Unidentified I/O Options: Analog telephone port (RJ-11), microphone in, audio in, audio out, game/MIDI port, TV/audio in, IDE interface Maximum Modem Rate 33.6Kbps Maximum Fax Rate 14.4Kbps Data Modulation Bell 103/212 Protocol ITU-T V.22, V.22bis, V.32, V.32bis, V.34 Fax Modulation ITU-T V.17, V.27ter, V.29 Protocol Error MNP5, V.42, V.42bis Correction/Compression Fax Class Class I & II Data Bus 16-bit ISA +------------------------------------------------------------+ | CONNECTIONS | |------------------------------------------------------------| | Function | Label | Function | Label | |------------------------------------------------------------| | Miromedia radio | CN1 | Microphone | CN5 | | connector | | in | | |--------------------------+--------------+------------+-----| | Line in (RJ-11) | CN2 | Audio in | CN6 | |--------------------------+--------------+------------+-----| | Internal telephone | CN3/pins 1-5 | Audio out | CN7 | | connector | | | | |--------------------------+--------------+------------+-----| | Microphone connector | CN3/pins 6-8 | MIDI/game | CN8 | | | | port | | |--------------------------+--------------+------------+-----| | TV/audio in | CN4 | | | +------------------------------------------------------------+ +------------------------------------------------------------+ | SUPPORTED COMMAND SET | |------------------------------------------------------------| | Basic AT Commands | |------------------------------------------------------------| | AT, '+++', A/ | |------------------------------------------------------------| | A, B, E, F, M, P, Q, T, V, X, Y | |------------------------------------------------------------| | &E, &V, &W, &Z | |------------------------------------------------------------| | Extended AT Commands | |------------------------------------------------------------| | \B \L, \V | |------------------------------------------------------------| | %E | |------------------------------------------------------------| | Special Commands | |------------------------------------------------------------| | "H, "N | |------------------------------------------------------------| | +MS | |------------------------------------------------------------| | S Registers | |------------------------------------------------------------| | S0, S1, S2, S3, S4, S5, S6, S7, S8, S9, S10, S11, S12, | | S25, S30, S32, S33 | |------------------------------------------------------------| | | |------------------------------------------------------------| | Note: See MHI Help File for full command documentation. | +------------------------------------------------------------+ PROPRIETARY AT COMMAND SET +------------------------------------------------------------+ | COMMUNICATIONS MODE | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] &Mn [cmds] | |--------------+---------------------------------------------| | Description: | Selects communications mode | |--------------+---------------------------------------------| | Command | Mode | |--------------+---------------------------------------------| | &M0 | Asynchronous mode | +------------------------------------------------------------+ +------------------------------------------------------------+ | COMMUNICATIONS MODE | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] &Qn [cmds] | |--------------+---------------------------------------------| | Description: | Selects communications mode options | |--------------+---------------------------------------------| | Command | Mode | |--------------+---------------------------------------------| | &Q0 | Asynchronous mode, serial port speed | | | follows connect speed. | +------------------------------------------------------------+ +------------------------------------------------------------+ | DATA SET READY (DSR) | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] &Sn [cmds] | |--------------+---------------------------------------------| | Description: | Selects DSR options | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | &S0 | DSR forced high | |--------------+---------------------------------------------| | &S1 | DSR high only while modem is handshaking or | | | connected | +------------------------------------------------------------+ +------------------------------------------------------------+ | DATA TERMINAL READY (DTR) | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] &Dn [cmds] | |--------------+---------------------------------------------| | Description: | Selects modem response to DTR | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | &D0 | DTR override | |--------------+---------------------------------------------| | &D1 | DTR toggle causes online command mode | |--------------+---------------------------------------------| | &D2 | DTR toggle causes modem to go on-hook | |--------------+---------------------------------------------| | &D3 | Loads profile as specified in &Y | +------------------------------------------------------------+ +------------------------------------------------------------+ | DIAL | |------------------------------------------------------------| | Type: | Immediate | |--------------+---------------------------------------------| | Format: | AT [cmds] D<#> [cmds] | |--------------+---------------------------------------------| | Description: | Dials telephone number according to any | | | modifiers included in the string | |--------------+---------------------------------------------| | Note: | Any combination of modifiers can be used to | | | produce the desired dial functions in | | | sequence. | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | DP | Pulse dialing enabled | |--------------+---------------------------------------------| | DR | Answer mode enabled; originate mode | | | disabled following handshake initiation. | |--------------+---------------------------------------------| | DS=n | Dial stored telephone number n | |--------------+---------------------------------------------| | DT | Tone dialing enabled/Pulse dialing disabled | |--------------+---------------------------------------------| | DW | Dialing resumed following dial tone | | | detection | |--------------+---------------------------------------------| | D, | Dialing paused for amount of time specified | | | in S8 register | |--------------+---------------------------------------------| | D! | Flash function initiated. Modem commanded | | | to go off-hook for specified time before | | | returning on-hook. | |--------------+---------------------------------------------| | D@ | Wait for Quite Answer function enabled. | | | Modem waits until a "quiet answer," a | | | ring-back signal followed by silence up to | | | the time specified in S7, is received prior | | | to executing the rest of the dial string. | |--------------+---------------------------------------------| | D; | Modem returned to idle state after dialing. | | | The semicolon can only be placed at the end | | | of the dial command | +------------------------------------------------------------+ +------------------------------------------------------------+ | FLOW CONTROL | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] &Kn [cmds] | |--------------+---------------------------------------------| | Description: | Enables flow control options | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | &K0 | Flow control disabled | |--------------+---------------------------------------------| | &K1 | RTS/CTS flow control enabled | |--------------+---------------------------------------------| | &K3 | RTS/CTS flow control enabled | |--------------+---------------------------------------------| | &K4 | XON/XOFF flow control enabled | |--------------+---------------------------------------------| | &K5 | Transparent XON/XOFF flow control enabled | +------------------------------------------------------------+ +------------------------------------------------------------+ | FORCE SPEED MODE | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] &Nn [cmds] | |--------------+---------------------------------------------| | Description: | Selects force speed option in V.32/V.32bis | | | mode | |--------------+---------------------------------------------| | Command | Mode | |--------------+---------------------------------------------| | &N0 | Support maximum allowable rate | |--------------+---------------------------------------------| | &N1 | Selects maximum allowable rate as specified | | | by register S28 | +------------------------------------------------------------+ +------------------------------------------------------------+ | GUARD TONE | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] &Gn [cmds] | |--------------+---------------------------------------------| | Description: | Commands the modem to transmit a guard tone | | | in V.22/V.22bis | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | &G0 | Guard tone disabled | |--------------+---------------------------------------------| | &G2 | 1800Hz guard tone enabled | +------------------------------------------------------------+ +------------------------------------------------------------+ | HOOK CONTROL | |------------------------------------------------------------| | Type: | Immediate | |--------------+---------------------------------------------| | Format: | AT [cmds] Hn [cmds] | |--------------+---------------------------------------------| | Description: | Selects whether the modem is on-hook or | | | off-hook | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | H0 | Modem commanded to go on-hook (hang-up) | +------------------------------------------------------------+ +------------------------------------------------------------+ | LINE TYPE | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] &Ln [cmds] | |--------------+---------------------------------------------| | Description: | Command nonfunctional | |--------------+---------------------------------------------| | Command | Line Type | |--------------+---------------------------------------------| | &L0 | Selects switched-network line mode | +------------------------------------------------------------+ +------------------------------------------------------------+ | ON-LINE | |------------------------------------------------------------| | Type: | Immediate | |---------------+--------------------------------------------| | Format: | AT [cmds] On [cmds] | |---------------+--------------------------------------------| | Description: | Controls on-line command (data | | | transmission) state options. | |------------------------------------------------------------| | Note: The O command must be placed at the end of the | | command string. | |------------------------------------------------------------| | Command | Function | |---------------+--------------------------------------------| | O0 | On-line command mode with no retraining | | | enabled | +------------------------------------------------------------+ +------------------------------------------------------------+ | PULSE DIALING RATIO | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] &Pn [cmds] | |--------------+---------------------------------------------| | Description: | Selects pulse dial make/break ratio. | |--------------+---------------------------------------------| | Note: | For compatibility purposes only; command | | | nonfunctional | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | &P0 | Returns OK | |--------------+---------------------------------------------| | &P1 | Returns OK | +------------------------------------------------------------+ +------------------------------------------------------------+ | REPORT INFORMATION | |------------------------------------------------------------| | Type: | Immediate | |--------------+---------------------------------------------| | Format: | AT [cmds] In [cmds] | |--------------+---------------------------------------------| | Description: | Displays information requested | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | I0 | Reports modem version | |--------------+---------------------------------------------| | I1 | Reports OK | |--------------+---------------------------------------------| | I2 | Tests and reports ROM checksum | |--------------+---------------------------------------------| | I3 | Reports version number of installed modem | | | files | |--------------+---------------------------------------------| | I4 | Reports modem capabilities string GENERIC | | | Mwave | +------------------------------------------------------------+ +------------------------------------------------------------+ | RESTORE PROFILE ON POWER-UP | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] &Yn [cmds] | |--------------+---------------------------------------------| | Description: | Restores a selected profile into the active | | | profile on power-up (hard reset) | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | &Y0 | Restore profile 0 on power-up | |--------------+---------------------------------------------| | &Y1 | Restore profile 1 on power-up | |--------------+---------------------------------------------| | &Y2 | Restore factory defaults on power-up | +------------------------------------------------------------+ +------------------------------------------------------------+ | SOFT RESET | |------------------------------------------------------------| | Type: | Immediate | |--------------+---------------------------------------------| | Format: | AT [cmds] Zn [cmds] | |--------------+---------------------------------------------| | Description: | Restores modem profiles previously saved in | | | non-volatile RAM using the &W command. | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | Z0 | Restore setting 0 | |--------------+---------------------------------------------| | Z1 | Restore setting 1 | |--------------+---------------------------------------------| | Z2 | Restore factory defaults | +------------------------------------------------------------+ +------------------------------------------------------------+ | SPEAKER VOLUME | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] Ln [cmds] | |--------------+---------------------------------------------| | Description: | Controls speaker volume | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | L0 | Minimum volume setting | |--------------+---------------------------------------------| | L1 | Low volume setting | |--------------+---------------------------------------------| | L2 | Medium volume setting | |--------------+---------------------------------------------| | L3 | Highest volume setting | +------------------------------------------------------------+ +------------------------------------------------------------+ | TRANSMIT CARRIER | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] Cn [cmds] | |--------------+---------------------------------------------| | Description: | Controls the transmit carrier switching | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | C1 | Transmit carrier enabled | +------------------------------------------------------------+ +------------------------------------------------------------+ | TRELLIS CODING | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] &Un [cmds] | |--------------+---------------------------------------------| | Description: | Enables/disables trellis coding | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | &U0 | V.32 trellis coding enabled | |--------------+---------------------------------------------| | &U1 | V.32 trellis coding disabled | +------------------------------------------------------------+ EXTENDED AT COMMANDS +------------------------------------------------------------+ | BREAK TYPE | |------------------------------------------------------------| | Type: | Configuration | |-------------------------+----------------------------------| | Format: | AT [cmds] \Kn [cmds] | |-------------------------+----------------------------------| | Description: | Configures action of break | | | signal | |------------------------------------------------------------| | Command | Break from DTE | Break received from | | | | remote modem | |------------+----------------------+------------------------| | \K0 | Online command mode | Buffers cleared, break | | | enabled, send no | sent to DTE | | | break to remote | | | | modem | | |------------+----------------------+------------------------| | \K1 | Break sent to remote | Buffers cleared, break | | | modem and buffered | sent to DTE | | | cleared | | |------------+----------------------+------------------------| | \K2 | Online command mode | Break sent immediately | | | enabled, send no | to DTE | | | break to remote | | | | modem | | |------------+----------------------+------------------------| | i \K3 | Send break to remote | Break sent immediately | | | modem immediately | to DTE | +------------------------------------------------------------+ +------------------------------------------------------------+ | COMPRESSION | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] %Cn [cmds] | |--------------+---------------------------------------------| | Description: | Selects data compression | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | %C0 | Data compression disabled | |--------------+---------------------------------------------| | %C1 | MNP5 enabled | +------------------------------------------------------------+ +------------------------------------------------------------+ | INACTIVITY TIMER | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] \Tn [cmds] | |--------------+---------------------------------------------| | Range: | 0-90 | |--------------+---------------------------------------------| | Unit: | 1minute | |--------------+---------------------------------------------| | Description: | Sets the length of time that the modem does | | | not receive information before it | | | disconnects. \T0 disables timer | +------------------------------------------------------------+ +------------------------------------------------------------+ | MAXIMUM BLOCK SIZE FOR TRANSMISSION | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] \An [cmds] | |--------------+---------------------------------------------| | Description: | Sets the maximum transmittable block size | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | \A0 | MNP block size is 64 characters | |--------------+---------------------------------------------| | \A1 | MNP block size is 128 characters | |--------------+---------------------------------------------| | \A2 | MNP block size is 192 characters | |--------------+---------------------------------------------| | \A3 | MNP block size is 256 characters | |--------------+---------------------------------------------| | \A4 | Variable block size | +------------------------------------------------------------+ SPECIAL COMMANDS +------------------------------------------------------------+ | DSVD MODE | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] -SSE=n [cmds] | |--------------+---------------------------------------------| | Description: | Select whether the modem will use DSVD | | | mode. | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | i -SSE=0 | DSVD mode disabled. | |--------------+---------------------------------------------| | -SSE=1 | DSVD mode enabled. | +------------------------------------------------------------+ +------------------------------------------------------------+ | UNIDENTIFIED | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] %TT6r, s, c, p [cmds] | |--------------+---------------------------------------------| | Description: | Unidentified | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | r=0 | 2400 (if s=0) | |--------------+---------------------------------------------| | r=1 | 4800bps | |--------------+---------------------------------------------| | r=2 | 7200bps | |--------------+---------------------------------------------| | r=3 | 9600bps | |--------------+---------------------------------------------| | r=4 | 1200bps | |--------------+---------------------------------------------| | r=5 | 14.4Kbps | |--------------+---------------------------------------------| | r=6 | 16.8Kbps | |--------------+---------------------------------------------| | r=7 | 19.2Kbps | |--------------+---------------------------------------------| | r=8 | 21.6Kbps | |--------------+---------------------------------------------| | r=9 | 24.0Kbps (if s1 0) | |--------------+---------------------------------------------| | r=A | 26.4Kbps (if s1 0) | |--------------+---------------------------------------------| | r=B | 28.8Kbps (if s1 0) | |--------------+---------------------------------------------| | s=7 | 2400 symbols per second | |--------------+---------------------------------------------| | s=8 | 3000 symbols per second | |--------------+---------------------------------------------| | s=9 | 3200 symbols per second | |--------------+---------------------------------------------| | c=0 | V.34 low carrier | |--------------+---------------------------------------------| | c>0 | V.34 high carrier | +------------------------------------------------------------+ +------------------------------------------------------------+ | V.42bis - MAXIMUM STRING LENGTH | |------------------------------------------------------------| | Type: | Immediate | |--------------+---------------------------------------------| | Format: | AT [cmds] "On [cmds] | |--------------+---------------------------------------------| | Range: | 6-250 | |--------------+---------------------------------------------| | Unit: | Characters | |--------------+---------------------------------------------| | Description: | Selects string size for V.42bis compression | +------------------------------------------------------------+ S(status) -REGISTERS +------------------------------------------------------------+ | BIT-MAPPED REGISTER S49 | |------------------------------------------------------------| | Format | AT [cmds] S49=n [cmds] | |--------------+---------------------------------------------| | Range: | 0-255 | |--------------+---------------------------------------------| | Unit: | Bit-mapped | |--------------+---------------------------------------------| | Description: | Selects call indicator, V.8, and V.34 | | | protocol. Bits are additive | |--------------+---------------------------------------------| | Bit | Value | Function | |------+-------+---------------------------------------------| | 0 | 0 | Not used | |------+-------+---------------------------------------------| | 1 | 0 | Call indicator enabled | | | | | | | 1 | Call indicator disabled | |------+-------+---------------------------------------------| | 2 | 0 | V.8 protocol enabled | | | | | | | 1 | V.8 protocol disabled | |------+-------+---------------------------------------------| | 3 | 0 | V.34 protocol enabled | | | | | | | 1 | V.34 protocol disabled | +------------------------------------------------------------+ +------------------------------------------------------------+ | BIT-MAPPED REGISTER S50 | |------------------------------------------------------------| | Format | AT [cmds] S50=n [cmds] | |--------------+---------------------------------------------| | Range: | 0-255 | |--------------+---------------------------------------------| | Unit: | Bit-mapped | |--------------+---------------------------------------------| | Description: | Selects baud rates that the V.34 modem will | | | request for reception | |--------------+---------------------------------------------| | Bit | Value | Function | |------+-------+---------------------------------------------| | 0 | 0 | 2400 baud receive symbol rate enabled | | | | | | | 1 | 2400 baud receive symbol rate disabled | |------+-------+---------------------------------------------| | 1 | 0 | 2743 baud receive symbol rate enabled | | | | | | | 1 | 2743 baud receive symbol rate disabled | |------+-------+---------------------------------------------| | 2 | 0 | 2800 baud receive symbol rate enabled | | | | | | | 1 | 2800 baud receive symbol rate disabled | |------+-------+---------------------------------------------| | 3 | 0 | 3000 baud receive symbol rate enabled | | | | | | | 1 | 3000 baud receive symbol rate disabled | |------+-------+---------------------------------------------| | 4 | 0 | 3200 baud receive symbol rate enabled | | | | | | | 1 | 3200 baud receive symbol rate disabled | |------+-------+---------------------------------------------| | 5 | 0 | 3429 baud receive symbol rate enabled | | | | | | | 1 | 3429 baud receive symbol rate disabled | |------+-------+---------------------------------------------| | 6 | 0 | Asymmetric symbol rates enabled | | | | | | | 1 | Asymmetric symbol rates disabled | |------+-------+---------------------------------------------| | 7 | 0 | Not used | +------------------------------------------------------------+ +------------------------------------------------------------+ | BIT-MAPPED REGISTER S52 | |------------------------------------------------------------| | Format | AT [cmds] S52=n [cmds] | |--------------+---------------------------------------------| | Range: | 0-255 | |--------------+---------------------------------------------| | Unit: | Bit-mapped | |--------------+---------------------------------------------| | Description: | Controls the various features of the V.34 | | | data pump | |--------------+---------------------------------------------| | Bit | Value | Function | |------+-------+---------------------------------------------| | 0 | 0 | Asymmetric data rates enabled | | | | | | | 1 | Asymmetric data rates disabled | |------+-------+---------------------------------------------| | 1 | 0 | Auxiliary channel enabled | | | | | | | 1 | Auxiliary channel disabled | |------+-------+---------------------------------------------| | 2-7 | 0 | Not used | +------------------------------------------------------------+ +------------------------------------------------------------+ | BIT-MAPPED REGISTER S53 | |------------------------------------------------------------| | Format | AT [cmds] S53=n [cmds] | |--------------+---------------------------------------------| | Range: | 0-255 | |--------------+---------------------------------------------| | Unit: | Bit-mapped | |--------------+---------------------------------------------| | Description: | Controls request options for: pre-emphasis, | | | constellation warping, constellation | | | shaping, and precoding | |--------------+---------------------------------------------| | Bit | Value | Function | |------+-------+---------------------------------------------| | 0 | 0 | Not used | |------+-------+---------------------------------------------| | 1 | 0 | Pre-emphasis requests disabled | | | | | | | 1 | Pre-emphasis requests enabled | |------+-------+---------------------------------------------| | 2 | 0 | Constellation warping requests disabled | | | | | | | 1 | Constellation warping requests enabled | |------+-------+---------------------------------------------| | 3 | 0 | Constellation shaping requests disabled | | | | | | | 1 | Constellation shaping requests enabled | |------+-------+---------------------------------------------| | 4 | 0 | Precoding requests disabled | | | | | | | 1 | Precoding requests enabled | |------+-------+---------------------------------------------| | 5-7 | 0 | Not used | +------------------------------------------------------------+ +------------------------------------------------------------+ | CALLING TONE | |------------------------------------------------------------| | Type: | Register | |---------------+--------------------------------------------| | Format | AT [cmds] S24=n [cmds] | |---------------+--------------------------------------------| | Description: | Enables/disables calling tone | |------------------------------------------------------------| | Command | Function | |------------+-----------------------------------------------| | S24=0 | Calling tone disabled. | |------------+-----------------------------------------------| | S24=1 | Calling tone enabled. | +------------------------------------------------------------+ +------------------------------------------------------------+ | DCE LINE SPEED | |------------------------------------------------------------| | Type: | Register | |--------------+---------------------------------------------| | Format | AT [cmds] S28=n [cmds] | |--------------+---------------------------------------------| | Description: | Sets the maximum allowable data exchange | | | rate attempted during handshake process. | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | S28=0 | Speed of last connection | |--------------+---------------------------------------------| | S28=1 | 50bps | |--------------+---------------------------------------------| | S28=2 | 75bps | |--------------+---------------------------------------------| | S28=3 | 110bps | |--------------+---------------------------------------------| | S28=4 | 134.5bps | |--------------+---------------------------------------------| | S28=5 | 150bps | |--------------+---------------------------------------------| | S28=6 | 300bps | |--------------+---------------------------------------------| | S28=8 | 1200bps | |--------------+---------------------------------------------| | S28=9 | 2400bps | |--------------+---------------------------------------------| | S28=10 | 4800bps | |--------------+---------------------------------------------| | S28=11 | 7200bps | |--------------+---------------------------------------------| | S28=12 | 9600bps | |--------------+---------------------------------------------| | S28=13 | 12.0Kbps | |--------------+---------------------------------------------| | S28=14 | 14.4Kbps | +------------------------------------------------------------+