MOTOROLA, INC. ============== VOICE SURFR 33600 INTERNAL Card Type Modem (asynchronous) Chip Set Unidentified I/O Options Speaker out, microphone Maximum Modem Rate 33.6Kbps Maximum Fax Rate 14.4Kbps Data Modulation Bell 103/212A Protocol V.34, V.32bis, V.32, V.22bis, V.21, Bell 212, Bell 103 Fax Modulation ITU-T V.17, V.29, V.27ter, V.21 CH 2 Protocol Error V.42, V.42bis, MNP5 Correction/Compression Fax Class Class I Data Bus 16-bit ISA Card Size Half-length, full-height card +------------------------------------------------------------+ | CONNECTIONS | |------------------------------------------------------------| | Function | Label | Function | Label | |------------------------------------------------------------| | Line in (RJ-11) | CN1 | Speaker out | CN3 | |-----------------------------+---------+-------------+------| | Line out (RJ-11) | CN2 | Microphone | CN4 | +------------------------------------------------------------+ +------------------------------------------------------------+ | USER CONFIGURABLE SETTINGS | |------------------------------------------------------------| | Function | Label | Position | |-------------------------------------+-------+--------------| | i Factory configured - do not alter | JP1 | Unidentified | |-------------------------------------+-------+--------------| | i Factory configured - do not alter | JP2 | Unidentified | |-------------------------------------+-------+--------------| | i Factory configured - do not alter | JP3 | Unidentified | |-------------------------------------+-------+--------------| | i Factory configured - do not alter | JP4 | Unidentified | |-------------------------------------+-------+--------------| | i Factory configured - do not alter | JP5 | Unidentified | |-------------------------------------+-------+--------------| | i Factory configured - do not alter | JP6 | Unidentified | |-------------------------------------+-------+--------------| | i Factory configured - do not alter | JP7 | Unidentified | |-------------------------------------+-------+--------------| | i Factory configured - do not alter | JP18 | Unidentified | |-------------------------------------+-------+--------------| | i Factory configured - do not alter | JP19 | Unidentified | |-------------------------------------+-------+--------------| | i Factory configured - do not alter | JP20 | Unidentified | |-------------------------------------+-------+--------------| | i Factory configured - do not alter | JP21 | Unidentified | |-------------------------------------+-------+--------------| | i Factory configured - do not alter | JP22 | Unidentified | |-------------------------------------+-------+--------------| | i Factory configured - do not alter | JP23 | Unidentified | |-------------------------------------+-------+--------------| | i Factory configured - do not alter | JP24 | Unidentified | +------------------------------------------------------------+ +------------------------------------------------------------+ | SERIAL PORT ADDRESS | |------------------------------------------------------------| | Setting | JP16 | JP17 | |--------------------+-------------------+-------------------| | COM1 (3F8h) | Open | Open | |--------------------+-------------------+-------------------| | COM2 (2F8h) | Open | Closed | |--------------------+-------------------+-------------------| | COM3 (3E8h) | Closed | Open | |--------------------+-------------------+-------------------| | COM4 (2E8h) | Closed | Closed | +------------------------------------------------------------+ +------------------------------------------------------------+ | INTERRUPT | |------------------------------------------------------------| |Setting| JP8 | JP9 |JP10 | JP11 | JP12 | JP13 | JP14 | JP15 | |-------+-----+-----+-----+------+------+------+------+------| | IRQ 2 |Open |Open |Open | Open | Open | Open | Open |Closed| |-------+-----+-----+-----+------+------+------+------+------| | IRQ 3 |Open |Open |Open | Open | Open | Open |Closed| Open | |-------+-----+-----+-----+------+------+------+------+------| | IRQ 4 |Open |Open |Open | Open | Open |Closed| Open | Open | |-------+-----+-----+-----+------+------+------+------+------| |i IRQ 5|Open |Open |Open | Open |Closed| Open | Open | Open | |-------+-----+-----+-----+------+------+------+------+------| | IRQ 7 |Open |Open |Open |Closed| Open | Open | Open | Open | +------------------------------------------------------------+ +------------------------------------------------------------+ | SUPPORTED COMMAND SET | |------------------------------------------------------------| | Basic AT Commands | |------------------------------------------------------------| | AT, '+++', A/ | |------------------------------------------------------------| | A, E, H, M, O, S, V, X, Z | |------------------------------------------------------------| | &F, &V, &W, &Y, &Z | |------------------------------------------------------------| | Extended AT Commands | |------------------------------------------------------------| | \K, \Q | |------------------------------------------------------------| | %A | |------------------------------------------------------------| | S Registers | |------------------------------------------------------------| | S0, S1, S2, S3, S4, S5, S6, S7, S8, S9, S10, S11, S12, | | S25, S26, S38 | |------------------------------------------------------------| | Note: See MHI Help File for full command documentation. | +------------------------------------------------------------+ Proprietary AT Command Set +------------------------------------------------------------+ | AUTO FALLFORWARD/FALLBACK | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] &An [cmds] | |--------------+---------------------------------------------| | Description: | Controls auto fallforward/fallback | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | i &A0 | Auto fallforward/fallback disabled | |--------------+---------------------------------------------| | &A1 | Auto fallforward/fallback enabled | +------------------------------------------------------------+ +------------------------------------------------------------+ | DATA CARRIER DETECT (DCD) | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] &Cn [cmds] | |--------------+---------------------------------------------| | Description: | Selects whether the DCD option is enabled | | | or disabled | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | i &C0 | DCD enabled | |--------------+---------------------------------------------| | &C1 | DCD enabled after carrier signal detected | |--------------+---------------------------------------------| | &C2 | Force DCD on and toggle DCD on disconnect | +------------------------------------------------------------+ +------------------------------------------------------------+ | DATA SET READY (DSR) | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] &Sn [cmds] | |--------------+---------------------------------------------| | Description: | Selects DSR options | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | &S0 | DSR forced high, off at disconnect | |--------------+---------------------------------------------| | i &S1 | DSR forced high in data or online mode, off | | | in command or idle mode | |--------------+---------------------------------------------| | &S2 | DSR follows carrier detect | |--------------+---------------------------------------------| | &S3 | DSR is forced high in all modes | +------------------------------------------------------------+ +------------------------------------------------------------+ | DATA TERMINAL READY (DTR) | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] &Dn [cmds] | |--------------+---------------------------------------------| | Description: | Selects modem response to DTR | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | i &D0 | Modem does not respond to DTR | |--------------+---------------------------------------------| | &D1 | Modem goes to command mode after DTR goes | | | is off | |--------------+---------------------------------------------| | &D2 | Modem goes to command mode and disconnects | | | (hangs up) after DTR goes off; Auto-Answer | | | is disabled. | |--------------+---------------------------------------------| | &D3 | Modem is initialized after DTR goes off | +------------------------------------------------------------+ +------------------------------------------------------------+ | DIAL | |------------------------------------------------------------| | Type: | Immediate | |--------------+---------------------------------------------| | Format: | AT [cmds] D<#> [cmds] | |--------------+---------------------------------------------| | Description: | Dials telephone number according to any | | | modifiers included in the string | |--------------+---------------------------------------------| | Note: | Any combination of modifiers can be used to | | | produce the desired dial functions in | | | sequence. | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | DL | Re-dial last number | |--------------+---------------------------------------------| | DP | Pulse dialing enabled | |--------------+---------------------------------------------| | DS=n | Dial stored telephone number n | |--------------+---------------------------------------------| | DT | Tone dialing enabled/Pulse dialing disabled | |--------------+---------------------------------------------| | DW | Dialing resumed following dial tone | | | detection | |--------------+---------------------------------------------| | D, | Dialing paused for amount of time specified | | | in S8 register | |--------------+---------------------------------------------| | D! | Flash function initiated. Modem commanded | | | to go off-hook for specified time before | | | returning on-hook. | |--------------+---------------------------------------------| | D@ | Wait for Quite Answer function enabled. | | | Modem waits until a "quiet answer," a | | | ring-back signal followed by silence up to | | | the time specified in S7, is received prior | | | to executing the rest of the dial string. | |--------------+---------------------------------------------| | D; | Modem returned to idle state after dialing. | | | The semicolon can only be placed at the end | | | of the dial command. | +------------------------------------------------------------+ +------------------------------------------------------------+ | JACK TYPE | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] &Hn [cmds] | |--------------+---------------------------------------------| | Description: | Selects maximum connect speed | |--------------+---------------------------------------------| | Command | Jack Type | |--------------+---------------------------------------------| | i &H0 | Auto-detect | |--------------+---------------------------------------------| | &H1 | V.34 | |--------------+---------------------------------------------| | &H2 | V.32bis automatic | |--------------+---------------------------------------------| | &H3 | V.32bis only | |--------------+---------------------------------------------| | &H4 | V.32 automatic | |--------------+---------------------------------------------| | &H5 | V.32 only | |--------------+---------------------------------------------| | &H6 | V.22 only (2400-1200bps) | |--------------+---------------------------------------------| | &H7 | V.22 only (1200bps) | |--------------+---------------------------------------------| | &H8 | Bell 212 only | |--------------+---------------------------------------------| | &H9 | Bell 103 only | |--------------+---------------------------------------------| | &H10 | V.21 only | +------------------------------------------------------------+ +------------------------------------------------------------+ | MODEM TO MODEM SPEED | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] &Gn [cmds] | |--------------+---------------------------------------------| | Description: | Sets the modem to modem speed | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | &G5 | 4.8Kbps | |--------------+---------------------------------------------| | &G6 | 7.2Kbps | |--------------+---------------------------------------------| | &G7 | 9.6Kbps | |--------------+---------------------------------------------| | &G8 | 12.0Kbps | |--------------+---------------------------------------------| | &G9 | 14.4Kbps | |--------------+---------------------------------------------| | &G10 | 16.8Kbps | |--------------+---------------------------------------------| | &G11 | 19.2Kbps | |--------------+---------------------------------------------| | &G12 | 21.6Kbps | |--------------+---------------------------------------------| | &G13 | 24.0Kbps | |--------------+---------------------------------------------| | &G14 | 26.4Kbps | |--------------+---------------------------------------------| | &G15 | 28.8Kbps | |--------------+---------------------------------------------| | &G16 | 31.2Kbps | |--------------+---------------------------------------------| | i &G17 | 33.6Kbps | +------------------------------------------------------------+ +------------------------------------------------------------+ | REPORT INFORMATION | |------------------------------------------------------------| | Type: | Immediate | |--------------+---------------------------------------------| | Format: | AT [cmds] In [cmds] | |--------------+---------------------------------------------| | Description: | Displays information requested | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | I0 | Reports product code | |--------------+---------------------------------------------| | I1 | Reports 000 | |--------------+---------------------------------------------| | I2 | Returns OK or ERROR | |--------------+---------------------------------------------| | I3 | Report firmware revision number | |--------------+---------------------------------------------| | I4 | Report configuration settings | +------------------------------------------------------------+ +------------------------------------------------------------+ | RESULT CODES | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] Qn [cmds] | |--------------+---------------------------------------------| | Description: | Enables modem to send result codes to the | | | DTE | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | i Q0 | Result code sending enabled | |--------------+---------------------------------------------| | Q1 | Result code sending disabled | |--------------+---------------------------------------------| | Q2 | Call progress messages on originate | +------------------------------------------------------------+ +------------------------------------------------------------+ | SPEAKER VOLUME | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] Ln [cmds] | |--------------+---------------------------------------------| | Description: | Controls speaker volume | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | L0 | Low volume setting | |--------------+---------------------------------------------| | L1 | Low volume setting | |--------------+---------------------------------------------| | i L2 | Medium volume setting | |--------------+---------------------------------------------| | L3 | Highest volume setting | +------------------------------------------------------------+ +------------------------------------------------------------+ | TRELLIS CODING | |------------------------------------------------------------| | Type: | Immediate | |--------------+---------------------------------------------| | Format: | AT [cmds] &Un | |--------------+---------------------------------------------| | Description: | Controls trellis coding | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | &U0 | Trellis coding enabled | |--------------+---------------------------------------------| | &U1 | Trellis coding disabled | +------------------------------------------------------------+ Extended AT Commands +------------------------------------------------------------+ | ANSWER MODE | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] %On [cmds] | |--------------+---------------------------------------------| | Description: | Sets the answer mode | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | %O0 | Answer mode if ringing | |--------------+---------------------------------------------| | %O1 | Force to answer mode | |--------------+---------------------------------------------| | %O2 | Automatic answer in originate mode | +------------------------------------------------------------+ +------------------------------------------------------------+ | CHARACTER ABORT DELAY | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] %Kn [cmds] | |--------------+---------------------------------------------| | Description: | Sets the delay before character abort | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | %K0 | Enable 2 second delay | |--------------+---------------------------------------------| | %K1 | Disable delay | +------------------------------------------------------------+ +------------------------------------------------------------+ | CHARACTER LENGTH | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] \Bn [cmds] | |--------------+---------------------------------------------| | Description: | Sets the character length | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | \B0 | 6 data bits, no parity, 1 stop bit | |--------------+---------------------------------------------| | \B1 | 7N1 | |--------------+---------------------------------------------| | \B2 | 7P1 | |--------------+---------------------------------------------| | \B3 | 8N1 | |--------------+---------------------------------------------| | \B4 | 7P2 | |--------------+---------------------------------------------| | \B5 | 8P1 | +------------------------------------------------------------+ +------------------------------------------------------------+ | COMPRESSION | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] %Cn [cmds] | |--------------+---------------------------------------------| | Description: | Selects data compression | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | %C0 | Data compression disabled | |--------------+---------------------------------------------| | %C1 | Data compression enabled | +------------------------------------------------------------+ +------------------------------------------------------------+ | CONNECT AND PROTOCOL | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] \Vn [cmds] | |--------------+---------------------------------------------| | Description: | Sets the connect and protocol message | | | functions | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | \V0 | Connect and protocol message reports modem | | | to modem speed | |--------------+---------------------------------------------| | \V1 | Connect and protocol message reports | | | computer to modem speed | |--------------+---------------------------------------------| | \V2 | Connect message reports computer to modem | | | speed/V.42 error correction | |--------------+---------------------------------------------| | \V3 | Connect message reports computer to modem | | | speed | +------------------------------------------------------------+ +------------------------------------------------------------+ | CONNECT MODE | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] \Nn [cmds] | |--------------+---------------------------------------------| | Description: | Controls the type of connection the modem | | | will operate in | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | \N0 | Normal operation | |--------------+---------------------------------------------| | \N1 | Direct operation | |--------------+---------------------------------------------| | \N2 | MNP connection only | |--------------+---------------------------------------------| | \N3 | V.42 LAPM, MNP or normal mode | |--------------+---------------------------------------------| | \N4 | V.42 LAPM connection only | |--------------+---------------------------------------------| | \N5 | V.42 LAPM or MNP mode | |--------------+---------------------------------------------| | \N6 | Simulated controlled carrier | +------------------------------------------------------------+ +------------------------------------------------------------+ | DTR | |------------------------------------------------------------| | Type: | Immediate | |--------------+---------------------------------------------| | Format: | AT [cmds] %Zn [cmds] | |--------------+---------------------------------------------| | Description: | Controls the DRT function | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | i %Z0 | Ignore DTR signal toggle | |--------------+---------------------------------------------| | %Z1 | Dial stored phone number (0-3) on DTR | | | toggle | |--------------+---------------------------------------------| | %Z2 | Attempt to connect on DTR toggle | +------------------------------------------------------------+ +------------------------------------------------------------+ | FLOW CONTROL | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] \Gn [cmds] | |--------------+---------------------------------------------| | Description: | Selects modem port flow control | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | \G0 | Flow control disabled | |--------------+---------------------------------------------| | \G1 | XON/XOFF flow control | |--------------+---------------------------------------------| | \G2 | XON/XOFF flow control only for transmitting | | | data | |--------------+---------------------------------------------| | \G3 | XON/XOFF flow control with pass-through | +------------------------------------------------------------+ +------------------------------------------------------------+ | PARITY | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] \Pn [cmds] | |--------------+---------------------------------------------| | Description: | Sets parity | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | \P0 | Even | |--------------+---------------------------------------------| | \P1 | Space | |--------------+---------------------------------------------| | \P2 | Odd | |--------------+---------------------------------------------| | \P3 | Mark | |--------------+---------------------------------------------| | \P4 | Automatic | +------------------------------------------------------------+ +------------------------------------------------------------+ | RETRAIN | |------------------------------------------------------------| | Type: | Immediate | |--------------+---------------------------------------------| | Format: | AT [cmds] %Q [cmds] | |--------------+---------------------------------------------| | Description: | Controls the retrain | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | %Q0 | Disable retrain | |--------------+---------------------------------------------| | %Q1 | Attempt up to 3 retrains and disconnect if | | | unsuccessful | |--------------+---------------------------------------------| | i %Q2 | Retrain until signal quality is good | +------------------------------------------------------------+ +------------------------------------------------------------+ | SPEED | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] \Tn [cmds] | |--------------+---------------------------------------------| | Description: | Sets the computer to modem speed | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | \T0 | Autobaud | |--------------+---------------------------------------------| | \T1 | Set to last AT command entry | |--------------+---------------------------------------------| | \T2 | 300bps | |--------------+---------------------------------------------| | \T3 | 1200bps | |--------------+---------------------------------------------| | \T4 | 2400bps | |--------------+---------------------------------------------| | \T5 | 4800bps | |--------------+---------------------------------------------| | \T6 | 7200bps | |--------------+---------------------------------------------| | \T7 | 9600bps | |--------------+---------------------------------------------| | \T8 | 12.0Kbps | |--------------+---------------------------------------------| | \T9 | 14.4Kbps | |--------------+---------------------------------------------| | \T10 | 16.8Kbps | |--------------+---------------------------------------------| | \T11 | 19.2Kbps | |--------------+---------------------------------------------| | \T12 | 21.6Kbps | |--------------+---------------------------------------------| | \T13 | 24.0Kbps | |--------------+---------------------------------------------| | \T14 | 26.4Kbps | |--------------+---------------------------------------------| | \T15 | 28.8Kbps | |--------------+---------------------------------------------| | \T16 | 31.2Kbps | |--------------+---------------------------------------------| | \T17 | 33.6Kbps | |--------------+---------------------------------------------| | \T18 | 38.4Kbps | |--------------+---------------------------------------------| | \T19 | 57.6Kbps | |--------------+---------------------------------------------| | \T20 | 76.8Kbps | |--------------+---------------------------------------------| | \T21 | 115.2Kbps | +------------------------------------------------------------+ +------------------------------------------------------------+ | TIMEOUT | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] \Cn [cmds] | |--------------+---------------------------------------------| | Description: | Sets timeout, fallback, data buffer | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | \C0 | Timeout and fallback, speed buffer, no data | | | buffer | |--------------+---------------------------------------------| | \C1 | Timeout and fallback, speed buffer, buffer | | | receive data | |--------------+---------------------------------------------| | \C2 | Auto reliable, fallback with fallback | | | character, speed buffer, no receive data | | | buffer | |--------------+---------------------------------------------| | \C3 | Timeout and fallback, ITU-T V.14, buffer | | | receive data | |--------------+---------------------------------------------| | \C4 | Timeout and fallback with fallback | | | character, ITU-T V.14, no data buffer | +------------------------------------------------------------+ S(status) -REGISTERS +------------------------------------------------------------+ | RETRANSMISSION COUNTER | |------------------------------------------------------------| | Type: | Register | |--------------+---------------------------------------------| | Format | AT [cmds] S70=n [cmds] | |--------------+---------------------------------------------| | Default: | 100 | |--------------+---------------------------------------------| | Range: | 0-255 | |--------------+---------------------------------------------| | Description: | Sets the number of retransmission tries | +------------------------------------------------------------+