MAXTECH CORPORATION =================== XPS 288IR (SF-1128HV/R16-PNP) Card Type Modem, Fax Chip Set Unidentified I/O Options Line in, line out, microphone in, speaker out Maximum Modem Rate 28.8Kbps Maximum Fax Rate 14.4Kbps Data Modulation Bell 103/212A Protocol ITU-T V.21, V.22, V.22bis, V.23, V.32, V.32bis, V.34 Fax Modulation ITU-T V.17, V.27ter, V.29 Protocol Error MNP5, V.42, V.42bis Correction/Compression Fax Class Class I & II Data Bus 16-bit ISA Card Size Half-length, half-height card +------------------------------------------------------------+ | CONNECTIONS | |------------------------------------------------------------| | Function | Label | Function | Label | |------------------------------------------------------------| | Line out | CN1 | Microphone in | CN3 | |--------------------------+----------+---------------+------| | Line in | CN2 | Speaker out | CN4 | +------------------------------------------------------------+ +------------------------------------------------------------+ | SUPPORTED COMMAND SET | |------------------------------------------------------------| | Basic AT Commands | |------------------------------------------------------------| | AT, '+++', A/ | |------------------------------------------------------------| | A, B, E, H, M, O, P, Q, T, V, W, X, Y, Z | |------------------------------------------------------------| | &C, &F, &P, &T, &V, &W, &Y, &Z | |------------------------------------------------------------| | Extended AT Commands | |------------------------------------------------------------| | \A, \B, \K, \N | |------------------------------------------------------------| | %C, %L, %Q | |------------------------------------------------------------| | S Registers | |------------------------------------------------------------| | S0, S1, S2, S3, S4, S5, S6, S7, S8, S9, S10, S11, S12, | | S14, S16, S18, S21, S22, S23, S24, S25, | |------------------------------------------------------------| | S26, S27, S29, S30, S31, S32, S33, S36, S37, S38, S39, | | S40, S41, S46, S48, S82, S86, S91, S92, | |------------------------------------------------------------| | S95 | |------------------------------------------------------------| | Special Commands | |------------------------------------------------------------| | #BDR, #CID=n, #CID?, #CID=?, #MDL?, #MFR?, #REV?, #TL, | | #VBQ?, #VBS, #VBT, #VCI?, #VLS, #VRA, | |------------------------------------------------------------| | #VRN, #VRX, #VSDB, #VSK, #VSP, #VSR, #VSS, #VTD, #VTM, | | #VTS, #VTX, +MS | |------------------------------------------------------------| | | |------------------------------------------------------------| | Note: See MHI Help File for full command documentation. | +------------------------------------------------------------+ Proprietary AT Command Set +------------------------------------------------------------+ | AUTOSCAN MODE | |------------------------------------------------------------| | Type: | Immediate | |--------------+---------------------------------------------| | Format: | AT [cmds] Nn [cmds] | |--------------+---------------------------------------------| | Description: | Enables/Disables Autoscan mode | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | N0 | Autoscan mode disabled | |--------------+---------------------------------------------| | i N1 | Autoscan mode enabled | +------------------------------------------------------------+ +------------------------------------------------------------+ | COMMUNICATIONS MODE | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] &Mn [cmds] | |--------------+---------------------------------------------| | Description: | Selects communications mode | |--------------+---------------------------------------------| | Command | Mode | |--------------+---------------------------------------------| | i &M0 | Asynchronous mode | +------------------------------------------------------------+ +------------------------------------------------------------+ | COMMUNICATIONS MODE (DATA LINK AND FALLBACK) | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] &Q [cmds] | |--------------+---------------------------------------------| | Description: | Configures data link options | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | &Q0 | Set Direct data link only | |--------------+---------------------------------------------| | &Q5 | Set V.42 data link with fallback options | |--------------+---------------------------------------------| | &Q6 | Set Normal data link only | +------------------------------------------------------------+ +------------------------------------------------------------+ | CTS | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] &Rn [cmds] | |--------------+---------------------------------------------| | Description: | Configures CTS settings | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | &R0 | Reserved | |--------------+---------------------------------------------| | i &R1 | Enables CTS operation based on flow control | | | settings | +------------------------------------------------------------+ +------------------------------------------------------------+ | DATA SET READY (DSR) | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] &Sn [cmds] | |--------------+---------------------------------------------| | Description: | Selects DSR options | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | &S0 | DSR forced high | |--------------+---------------------------------------------| | i &S1 | DSR is off while in command mode and set on | | | in on-line mode | +------------------------------------------------------------+ +------------------------------------------------------------+ | DATA TERMINAL READY (DTR) | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] &Dn [cmds] | |--------------+---------------------------------------------| | Description: | Selects modem response to DTR | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | i &D0 | Modem does not respond to DTR | |--------------+---------------------------------------------| | &D1 | Modem goes to command mode after DTR goes | | | is off | |--------------+---------------------------------------------| | &D2 | Modem goes to command mode and disconnects | | | (hangs up) after DTR goes off; Auto-Answer | | | is disabled. | |--------------+---------------------------------------------| | &D3 | Modem is initialized after DTR goes off | +------------------------------------------------------------+ +------------------------------------------------------------+ | DIAL | |------------------------------------------------------------| | Type: | Immediate | |--------------+---------------------------------------------| | Format: | AT [cmds] D<#> [cmds] | |--------------+---------------------------------------------| | Description: | Dials telephone number according to any | | | modifiers included in the string | |--------------+---------------------------------------------| | Note: | Any combination of modifiers can be used to | | | produce the desired dial functions in | | | sequence. | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | DL | Re-dial last number | |--------------+---------------------------------------------| | DP | Pulse dialing enabled | |--------------+---------------------------------------------| | i DT | Tone dialing enabled/Pulse dialing disabled | |--------------+---------------------------------------------| | DW | Dialing resumed following dial tone | | | detection | |--------------+---------------------------------------------| | D, | Dialing paused for amount of time specified | | | in S8 register | |--------------+---------------------------------------------| | D"WXY" | Optional method of denoting telephone | | | numbers. Letters enclosed in quotes are | | | interpreted as numbers according to the | | | system found on a telephone keypad. | |--------------+---------------------------------------------| | D! | Flash function initiated. Modem commanded | | | to go off-hook for specified time before | | | returning on-hook. | |--------------+---------------------------------------------| | D@ | Wait for Quite Answer function enabled. | | | Modem waits until a "quiet answer," a | | | ring-back signal followed by silence up to | | | the time specified in S7, is received prior | | | to executing the rest of the dial string. | |--------------+---------------------------------------------| | D; | Modem returned to idle state after dialing. | | | The semicolon can only be placed at the end | | | of the dial command. | +------------------------------------------------------------+ +------------------------------------------------------------+ | FLOW CONTROL | |------------------------------------------------------------| | Type: | Immediate | |--------------+---------------------------------------------| | Format: | AT [cmds] &K [cmds] | |--------------+---------------------------------------------| | Description: | Configures flow control settings | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | &K0 | Flow control disabled | |--------------+---------------------------------------------| | &K3 | RTS/CTS hardware flow control enabled | |--------------+---------------------------------------------| | &K4 | XON/XOFF software flow control enabled | |--------------+---------------------------------------------| | &K5 | Transparent XON/XOFF software flow control | | | enabled | |--------------+---------------------------------------------| | &K6 | RTS/CTS & XON/XOFF flow control enabled | +------------------------------------------------------------+ +------------------------------------------------------------+ | GUARD TONE | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] &Gn [cmds] | |--------------+---------------------------------------------| | Description: | Enables/Disables and configures guard tone | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | i &G0 | Guard tone disabled | |--------------+---------------------------------------------| | &G1 | Guard tone disabled | |--------------+---------------------------------------------| | &G2 | Set guard tone at 1800Hz | +------------------------------------------------------------+ +------------------------------------------------------------+ | HAYES SMARTMODEM 300 COMPATIBILITY | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] Xn [cmds] | |--------------+---------------------------------------------| | Description: | Configures modem response and blind dialing | | | capabilities | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | X0 | Sets modem to use Hayes Smartmodem 300 | | | responses and blind dialing | |--------------+---------------------------------------------| | X1 | Sets modem to use Hayes Smartmodem 300 | | | responses, CONNECT responses, and blind | | | dialing | |--------------+---------------------------------------------| | X2 | Sets modem to use Hayes Smartmodem 300 | | | responses, CONNECT responses, dial tone | | | detection, and blind dialing | |--------------+---------------------------------------------| | X3 | Sets modem to use Hayes Smartmodem 300 | | | responses, CONNECT responses, busy | | | detection, and blind dialing | |--------------+---------------------------------------------| | i X4 | Set modem to use all responses, dial tone | | | detection, and busy signal detection | +------------------------------------------------------------+ +------------------------------------------------------------+ | LINE TYPE | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] &Ln [cmds] | |--------------+---------------------------------------------| | Description: | Selects line type | |--------------+---------------------------------------------| | Command | Line Type | |--------------+---------------------------------------------| | i &L0 | Switched line (PSTN/Dial-up) | +------------------------------------------------------------+ +------------------------------------------------------------+ | REPORT INFORMATION | |------------------------------------------------------------| | Type: | Immediate | |--------------+---------------------------------------------| | Format: | AT [cmds] In [cmds] | |--------------+---------------------------------------------| | Description: | Displays information requested | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | I0 | Reports product ID | |--------------+---------------------------------------------| | I1 | Reports ROM checksum | |--------------+---------------------------------------------| | I2 | Tests and reports internal memory | |--------------+---------------------------------------------| | I3 | Reports firmware ID | |--------------+---------------------------------------------| | I4 | Reports reserved ID | +------------------------------------------------------------+ +------------------------------------------------------------+ | SPEAKER VOLUME | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] Ln [cmds] | |--------------+---------------------------------------------| | Description: | Controls speaker volume | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | L0 | Low volume setting | |--------------+---------------------------------------------| | i L1 | Low volume setting | |--------------+---------------------------------------------| | L2 | Medium volume setting | |--------------+---------------------------------------------| | L3 | Highest volume setting | +------------------------------------------------------------+ Extended AT Commands +------------------------------------------------------------+ | AUTO-RETRAIN - AUTO-FALLBACK/FALL-FORWARD | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] %En [cmds] | |--------------+---------------------------------------------| | Description: | Controls auto-retrain mode and | | | fallback/fall-forward | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | %E0 | Auto-retrain disabled | |--------------+---------------------------------------------| | %E1 | Auto-retrain enabled | +------------------------------------------------------------+ +------------------------------------------------------------+ | CONNECT MODE | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] \Nn [cmds] | |--------------+---------------------------------------------| | Description: | Configures data link and fallback options | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | \N0 | Set Normal data link only | |--------------+---------------------------------------------| | \N1 | Set Direct data link only | |--------------+---------------------------------------------| | \N2 | Set V.42 or MNP data link only | |--------------+---------------------------------------------| | i \N3 | Set V.42/MNP/Normal data link | |--------------+---------------------------------------------| | \N4 | Set V.42 data link only | |--------------+---------------------------------------------| | \N5 | Set MNP data link only | +------------------------------------------------------------+