NEWCOM, INC. ============ 56KIFXSP (A) Card Type Modem (asynchronous) Chip Set Unidentified I/O Options Microphone, speaker/line out Maximum Modem Rate 56Kbps Maximum Fax Rate 14.4Kbps Data Modulation Bell 103A/212A Protocol V.34, V.32bis, V.32, V.23, V.22bis, V.22, V.21, K56flex, V.90 Fax Modulation V.17, V.29, V.27ter, V.21CH2 Protocol Error V.42, MNP10, V.42bis, MNP5 Correction/Compression Fax Class Class I & II Data Bus 16-bit ISA +------------------------------------------------------------+ | CONNECTIONS | |------------------------------------------------------------| | Function | Label | Function | Label | |------------------------------------------------------------| | Wake on ring | CN1 | Line out | CN5 | |---------------------------+---------+----------------+-----| | Microphone - internal | CN2 | Microphone - | CN6 | | | | external | | |---------------------------+---------+----------------+-----| | TAD (sound card) | CN3 | Speaker/line | CN7 | | connector | | out | | |---------------------------+---------+----------------+-----| | Line in | CN4 | | | +------------------------------------------------------------+ +---------------------------------------------------------+ | SUPPORTED COMMAND SET | |---------------------------------------------------------| | Basic AT Commands | |---------------------------------------------------------| | AT, A/ | |---------------------------------------------------------| | A, C, E, H, M, N, O, P, Q, T, V, W, X, Y, Z | |---------------------------------------------------------| | &C, &D, &J, &L, &M, &P, &Q, &R, &T, &V, &W, &X, &Y, &Z | |---------------------------------------------------------| | Extended AT Commands | |---------------------------------------------------------| | \A, \B, \G, \K, \L, \N | |---------------------------------------------------------| | %C, %Q | |---------------------------------------------------------| | S-Registers | |---------------------------------------------------------| | A list of S-registers was unavailable | |---------------------------------------------------------| | Note: See MHI Help File for full command documentation. | +---------------------------------------------------------+ Proprietary AT Command Set +------------------------------------------------------------+ | COMMUNICATION PROTOCOLS | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] Bn [cmds] | |--------------+---------------------------------------------| | Description: | Selects the communication protocol for data | | | calls | |------------------------------------------------------------| | Note: The B command allows the simultaneous selection | | of more than one suffix, enabling multiple protocols. | |------------------------------------------------------------| | Command | Protocol | |--------------+---------------------------------------------| | B0 | ITU-T V.22 at 300 or 1200bps | |--------------+---------------------------------------------| | B1 | Bell 212A at 300 or 1200bps | |--------------+---------------------------------------------| | B15 | V.21 connection at 300bps | |--------------+---------------------------------------------| | B16 | Bell 103 connection at 300bps | +------------------------------------------------------------+ +------------------------------------------------------------+ | DIAL | |------------------------------------------------------------| | Type: | Immediate | |--------------+---------------------------------------------| | Format: | AT [cmds] D<#> [cmds] | |--------------+---------------------------------------------| | Description: | Dials telephone number according to any | | | modifiers included in the string | |--------------+---------------------------------------------| | Note: | Any combination of modifiers can be used to | | | produce the desired dial functions in | | | sequence. | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | DL | Re-dial last number | |--------------+---------------------------------------------| | DP | Pulse dialing enabled | |--------------+---------------------------------------------| | DR | Answer mode enabled; originate mode | | | disabled following handshake initiation. | |--------------+---------------------------------------------| | DS=n | Dial stored telephone number n | |--------------+---------------------------------------------| | DT | Tone dialing enabled/Pulse dialing disabled | |--------------+---------------------------------------------| | DW | Dialing resumed following dial tone | | | detection | |--------------+---------------------------------------------| | D, | Dialing paused for amount of time specified | | | in S8 register | |--------------+---------------------------------------------| | D! | Flash function initiated. Modem commanded | | | to go off-hook for specified time before | | | returning on-hook. | |--------------+---------------------------------------------| | D@ | Wait for Quite Answer function enabled. | | | Modem waits until a "quiet answer," a | | | ring-back signal followed by silence up to | | | the time specified in S7, is received prior | | | to executing the rest of the dial string. | |--------------+---------------------------------------------| | D^ | Turns on the periodic 1300Hz calling tone. | |--------------+---------------------------------------------| | D; | Modem returned to idle state after dialing. | | | The semicolon can only be placed at the end | | | of the dial command. | +------------------------------------------------------------+ +------------------------------------------------------------+ | LINE MODULATION | |------------------------------------------------------------| | Type: | Configuration | |----------------------+-------------------------------------| | Format: | AT [cmds] Fn [cmds] | |----------------------+-------------------------------------| | Description: | Selects line modulation | |------------------------------------------------------------| | Note: This command is only supported on older modems | |------------------------------------------------------------| | Command | Function | |----------------------+-------------------------------------| | F0 | Auto-detect mode | |----------------------+-------------------------------------| | F1 | V.21 or Bell 103 | |----------------------+-------------------------------------| | F3 | V.23 | |----------------------+-------------------------------------| | F4 | V.22 or Bell 212A @ 1200bps | |----------------------+-------------------------------------| | F5 | V.22bis | |----------------------+-------------------------------------| | F6 | V.32bis or V.32 @ 4800bps | |----------------------+-------------------------------------| | F7 | V.32bis @ 7200bps | |----------------------+-------------------------------------| | F8 | V.32bis for V.32 @ 9600bps | |----------------------+-------------------------------------| | F9 | V.32bis @ 12000bps | |----------------------+-------------------------------------| | F10 | V.32bis @ 14400bps | +------------------------------------------------------------+ +------------------------------------------------------------+ | REPORT INFORMATION | |------------------------------------------------------------| | Type: | Immediate | |--------------+---------------------------------------------| | Format: | AT [cmds] In [cmds] | |--------------+---------------------------------------------| | Description: | Displays information requested | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | I0 | Reports product code | |--------------+---------------------------------------------| | I1 | Reports ROM checksum | |--------------+---------------------------------------------| | I2 | Tests and reports ROM checksum | |--------------+---------------------------------------------| | I3 | Reports firmware revision level | |--------------+---------------------------------------------| | I4 | Reports product capabilities | |--------------+---------------------------------------------| | I5 | Reports country code | |--------------+---------------------------------------------| | I6 | Reports modem data pump control | +------------------------------------------------------------+ +------------------------------------------------------------+ | SPEAKER VOLUME | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] Ln [cmds] | |--------------+---------------------------------------------| | Description: | Controls speaker volume | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | L0 | Low volume setting | |--------------+---------------------------------------------| | L1 | Low volume setting | |--------------+---------------------------------------------| | i L2 | Medium volume setting | |--------------+---------------------------------------------| | L3 | Highest volume setting | +------------------------------------------------------------+ +------------------------------------------------------------+ | FACTORY DEFAULT PROFILE | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] &F [cmds] | |--------------+---------------------------------------------| | Description: | Sets values in active profile to values | | | found in the default profile | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | &F0 | Restore factory profile 0 | |--------------+---------------------------------------------| | &F1 | Restore factory profile 1 | +------------------------------------------------------------+ +------------------------------------------------------------+ | GUARD TONE | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] &Gn [cmds] | |--------------+---------------------------------------------| | Description: | Commands the modem to transmit a guard tone | | | in V.22/V.22bis | |------------------------------------------------------------| | Note: Used primarily for international data | | transmission | |------------------------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | i &G0 | Guard tone disabled | |--------------+---------------------------------------------| | &G1 | Guard tone disabled | |--------------+---------------------------------------------| | &G2 | 1800Hz guard tone enabled | +------------------------------------------------------------+ +------------------------------------------------------------+ | FLOW CONTROL | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] &Kn [cmds] | |--------------+---------------------------------------------| | Description: | Enables flow control options | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | &K0 | Flow control disabled | |--------------+---------------------------------------------| | i &K3 | RTS/CTS flow control enabled | |--------------+---------------------------------------------| | &K4 | XON/XOFF flow control enabled | |--------------+---------------------------------------------| | &K5 | Transparent XON/XOFF flow control enabled | |--------------+---------------------------------------------| | &K6 | RTS/CTS, XON/XOFF, and DTE/DCE flow control | | | enabled | +------------------------------------------------------------+ +------------------------------------------------------------+ | DATA SET READY (DSR) | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] &Sn [cmds] | |--------------+---------------------------------------------| | Description: | Selects DSR options | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | &S0 | DSR forced high | |--------------+---------------------------------------------| | i &S1 | DSR high only while modem is handshaking or | | | connected | +------------------------------------------------------------+ Extended AT Commands +------------------------------------------------------------+ | AUTO-RETRAIN - AUTO-FALLBACK/FALL-FORWARD | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] %En [cmds] | |--------------+---------------------------------------------| | Description: | Controls auto-retrain mode and | | | fallback/fall-forward | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | %E0 | Auto-retrain disabled | |--------------+---------------------------------------------| | %E1 | Auto-retrain enabled | +------------------------------------------------------------+