HARMONY MULTIMEDIA ================== HM 18008-5 Card Type Modem (asynchronous) Chip Set Unidentified I/O Options Microphone, headphone, speaker out, line in, line out Maximum Modem Rate 33.6Kbps Maximum Fax Rate 14.4Kbps Data Modulation Bell 103/212A Protocol ITU-T V.34+, V.34, V.32bis, V.32, V.22bis, V.22A/B, V.23, V.21, Fax Modulation ITU-T V.17, V.29, V.27ter, V.21CH 2 Protocol Error V.42, V.42bis, MNP5 Correction/Compression Fax Class Class I Data Bus 16-bit ISA Card Size Half-length, full-height card +------------------------------------------------------------+ | CONNECTIONS | |------------------------------------------------------------| | Function | Label | Function | Label | |------------------------------------------------------------| | Line in | CN1 | Headphone | CN4 | |----------------------------+----------+-------------+------| | Line out | CN2 | Speaker out | CN5 | |----------------------------+----------+-------------+------| | Microphone | CN3 | | | +------------------------------------------------------------+ +------------------------------------------------------------+ | SERIAL PORT ADDRESS | |------------------------------------------------------------| | Setting | JP1/A | JP1/B | JP1/C | JP1/D | |-------------+-----------+-----------+-----------+----------| | COM1 (3F8h) | Open | Open | Closed | Closed | |-------------+-----------+-----------+-----------+----------| | COM2 (2F8h) | Closed | Open | Open | Closed | |-------------+-----------+-----------+-----------+----------| | COM3 (3E8h) | Open | Closed | Closed | Open | |-------------+-----------+-----------+-----------+----------| | COM4 (2E8h) | Closed | Closed | Open | Open | +------------------------------------------------------------+ +-----------------------------------------------------------------------------+ | INTERRUPT | |-----------------------------------------------------------------------------| |Setting|JP1/E |JP1/F |JP1/G |JP1/H |JP1/I |JP1/J |JP1/K |JP1/L |JP1/M |JP1/N | |-------+------+------+------+------+------+------+------+------+------+------| | IRQ 3 |Closed| Open | Open | Open | Open | Open | Open | Open | Open | Open | |-------+------+------+------+------+------+------+------+------+------+------| | IRQ 4 | Open |Closed| Open | Open | Open | Open | Open | Open | Open | Open | |-------+------+------+------+------+------+------+------+------+------+------| | IRQ 5 | Open | Open |Closed| Open | Open | Open | Open | Open | Open | Open | |-------+------+------+------+------+------+------+------+------+------+------| | IRQ 7 | Open | Open | Open |Closed| Open | Open | Open | Open | Open | Open | |-------+------+------+------+------+------+------+------+------+------+------| |IRQ 10 | Open | Open | Open | Open | Open | Open |Closed| Open | Open | Open | |-------+------+------+------+------+------+------+------+------+------+------| |IRQ 11 | Open | Open | Open | Open | Open |Closed| Open | Open | Open | Open | |-------+------+------+------+------+------+------+------+------+------+------| |IRQ 12 | Open | Open | Open | Open |Closed| Open | Open | Open | Open | Open | |-------+------+------+------+------+------+------+------+------+------+------| | PnP |Closed|Closed|Closed|Closed|Closed|Closed|Closed|Closed|Closed|Closed| +-----------------------------------------------------------------------------+ +------------------------------------------------------------+ | SUPPORTED COMMAND SET | |------------------------------------------------------------| | Basic AT Commands | |------------------------------------------------------------| | AT, A/ | |------------------------------------------------------------| | A, C, D, E, F, H, M, O, P, Q, T, V, X, Y, Z | |------------------------------------------------------------| | &C, &F, &G, &T, &W, &Y, &Z | |------------------------------------------------------------| | Extended AT Commands | |------------------------------------------------------------| | \A, \B, \C, \G, \J, \K, \O, \U, \X, \Y, \Z | |------------------------------------------------------------| | %A, | |------------------------------------------------------------| | S Registers | |------------------------------------------------------------| | S0, S1, S2, S3, S4, S5, S6, S7, S8, S9, S10, S11, S12, | | S16, S18, S24, S25, S26, S29, | |------------------------------------------------------------| | S38, S39, S46, S48, S82, S86, S90, S91, S92, S95, S99, | | S108, S109, S110, 201 | |------------------------------------------------------------| | Special Commands | |------------------------------------------------------------| | "H, -J | |------------------------------------------------------------| | Note: See MHI Help File for full command documentation. | +------------------------------------------------------------+ Proprietary AT Command Set +------------------------------------------------------------+ | AUTO-MODE DETECTION | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] Nn [cmds] | |--------------+---------------------------------------------| | Description: | Selects various options for the automatic | | | detection and negotiation of protocols | | | during the handshake process if the modem | | | is communicating with a remote modem of | | | dissimilar speed. | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | N0 | Handshake only at DTE- to-modem data rate | |--------------+---------------------------------------------| | i N1 | Begins handshake DTE-to-modem rate at | | | highest compatible rate | +------------------------------------------------------------+ +------------------------------------------------------------+ | AUXILIARY RELAY | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] &Jn [cmds] | |--------------+---------------------------------------------| | Description: | Sets the auxiliary relay function | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | i &J0 | Auxiliary relay never operated | |--------------+---------------------------------------------| | &J1 | Activates auxiliary relay when modem is | | | off-hook | +------------------------------------------------------------+ +------------------------------------------------------------+ | COMMUNICATIONS MODE | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] &Mn [cmds] | |--------------+---------------------------------------------| | Description: | Selects communications mode | |--------------+---------------------------------------------| | Command | Mode | |--------------+---------------------------------------------| | i &M0 | Asynchronous mode (modem supports | | | asynchronous mode only) | +------------------------------------------------------------+ +------------------------------------------------------------+ | COMMUNICATIONS MODE | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] &Qn [cmds] | |--------------+---------------------------------------------| | Description: | Selects communications mode options | |--------------+---------------------------------------------| | Command | Mode | |--------------+---------------------------------------------| | i &Q0 | Asynchronous mode (modem supports | | | asynchronous mode only.) | +------------------------------------------------------------+ +------------------------------------------------------------+ | COMMUNICATION PROTOCOLS | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] Bn [cmds] | |--------------+---------------------------------------------| | Description: | Selects the communication protocol for data | | | calls | |------------------------------------------------------------| | Note: The B command allows the simultaneous selection | | of more than one suffix, enabling multiple protocols. | |------------------------------------------------------------| | Command | Protocol | |--------------+---------------------------------------------| | B0 | ITU-T V.22 at 300 or 1200bps | |--------------+---------------------------------------------| | B1 | Bell 212A at 300 or 1200bps | |--------------+---------------------------------------------| | B2 | ITU-T V.23 at 75 or 1200bps | |--------------+---------------------------------------------| | B3 | ITU-T V.22 at 1200 or 75bps | +------------------------------------------------------------+ +------------------------------------------------------------+ | CONFIGURATION PROFILES | |------------------------------------------------------------| | Type: | Immediate | |--------------+---------------------------------------------| | Format: | AT [cmds] &V [cmds] | |--------------+---------------------------------------------| | Description: | Displays active and stored configuration | | | profiles | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | i &V0 | View stored profile 0 | |--------------+---------------------------------------------| | &V1 | View stored profile 1 | |--------------+---------------------------------------------| | &V2 | View relay and general-purpose I/O status | +------------------------------------------------------------+ +------------------------------------------------------------+ | DATA SET READY (DSR) | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] &Sn [cmds] | |--------------+---------------------------------------------| | Description: | Selects DSR options | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | &S0 | DSR forced high | |--------------+---------------------------------------------| | i &S1 | DSR high only while modem is handshaking or | | | connected | +------------------------------------------------------------+ +------------------------------------------------------------+ | DATA TERMINAL READY (DTR) | |------------------------------------------------------------| | Type: | Configuration | |---------------+--------------------------------------------| | Format: | AT [cmds] &Dn [cmds] | |---------------+--------------------------------------------| | Description: | Selects modem response to DTR | |------------------------------------------------------------| | Note: The action each variant of &D causes depends on | | the setting of &Q | |------------------------------------------------------------| | Command | Function | |---------------+--------------------------------------------| | i &D0 | Modem does not respond to DTR | |---------------+--------------------------------------------| | &D1 | Modem goes to command mode after DTR goes | | | is off | |---------------+--------------------------------------------| | &D2 | Modem goes to command mode and disconnects | | | (hangs up) after DTR goes off; Auto-Answer | | | is disabled. | |---------------+--------------------------------------------| | &D3 | Modem is initialized after DTR goes off | +------------------------------------------------------------+ +------------------------------------------------------------+ | EXTENDED RESULT CODES | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] Wn [cmds] | |--------------+---------------------------------------------| | Description: | Enables selection of additional result | | | codes when S95=0; otherwise, S95 takes | | | precedence. | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | i W0 | DTE speed response codes | |--------------+---------------------------------------------| | W1 | DTE speed response codes | |--------------+---------------------------------------------| | W2 | DCE speed response codes | |--------------+---------------------------------------------| | W3 | DTE speed response codes with error correct | | | and data compression | |--------------+---------------------------------------------| | W4 | Reports protocol , data compression, and | | | DTE data rate | +------------------------------------------------------------+ +------------------------------------------------------------+ | FLOW CONTROL | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] &Kn [cmds] | |--------------+---------------------------------------------| | Description: | Enables flow control options | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | &K0 | Flow control disabled | |--------------+---------------------------------------------| | i &K3 | Bi-directional hardware flow control | |--------------+---------------------------------------------| | &K4 | XON/XOFF flow control enabled | +------------------------------------------------------------+ +------------------------------------------------------------+ | PULSE DIALING RATIO | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] &Pn [cmds] | |--------------+---------------------------------------------| | Description: | Selects pulse dial make/break ratio | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | i &P0 | 39/61ms at 10pps (North America) | |--------------+---------------------------------------------| | &P1 | 33/67ms at 10pps (Europe) | +------------------------------------------------------------+ +------------------------------------------------------------+ | REPORT INFORMATION | |------------------------------------------------------------| | Type: | Immediate | |--------------+---------------------------------------------| | Format: | AT [cmds] In [cmds] | |--------------+---------------------------------------------| | Description: | Displays information requested | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | I0 | Reports product code | |--------------+---------------------------------------------| | I1 | Reports modem chip firmware version | |--------------+---------------------------------------------| | I2 | Tests and reports ROM checksum | |--------------+---------------------------------------------| | I3 | Reports chipset name | |--------------+---------------------------------------------| | I4 | Reserved | |--------------+---------------------------------------------| | I5 | Reserved for modem chip hardware | | | configuration | |--------------+---------------------------------------------| | I6 | Reports country code | |--------------+---------------------------------------------| | I7 | Reports version of board manufacturer | | | firmware | |--------------+---------------------------------------------| | I8 | Reports features of modem firmware | |--------------+---------------------------------------------| | I10 | Reports modem board configuration-bits set | | | by board manufacturer | |--------------+---------------------------------------------| | I11 | Reports modem board configuration-bits set | | | by board manufacturer | |--------------+---------------------------------------------| | I14 | Reports SAFE device | |--------------+---------------------------------------------| | I20 | Reports chip manufacturer's silicon version | |--------------+---------------------------------------------| | I21 | Reports chip manufacturer's firmware | | | version | |--------------+---------------------------------------------| | I22 | Reports chip manufacturer's name | |--------------+---------------------------------------------| | I23 | Reports chip manufacturer's product model | +------------------------------------------------------------+ +------------------------------------------------------------+ | SPEAKER VOLUME | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] Ln [cmds] | |--------------+---------------------------------------------| | Description: | Controls speaker volume | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | L0 | Low volume setting | |--------------+---------------------------------------------| | L1 | Low volume setting | |--------------+---------------------------------------------| | i L2 | Medium volume setting | |--------------+---------------------------------------------| | L3 | Highest volume setting | +------------------------------------------------------------+ +------------------------------------------------------------+ | TRELLIS CODING | |------------------------------------------------------------| | Type: | Immediate | |--------------+---------------------------------------------| | Format: | AT [cmds] &u [cmds] | |--------------+---------------------------------------------| | Description: | Controls Trellis coding | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | i &U0 | Enable Trellis coding with QAM as fallback | |--------------+---------------------------------------------| | &U1 | QAM modulation only | +------------------------------------------------------------+ Extended AT Command Set +------------------------------------------------------------+ | AUTO-FALLBACK/FALL-FORWARD | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] %Gn [cmds] | |--------------+---------------------------------------------| | Description: | Selects auto-fallback/fall-forward | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | %G0 | Auto-fallback/fall-forward disabled | |--------------+---------------------------------------------| | %G1 | Generate data modem calling tone | +------------------------------------------------------------+ +------------------------------------------------------------+ | AUTO-RETRAIN | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] %En [cmds] | |--------------+---------------------------------------------| | Description: | Controls auto-retrain mode | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | %E0 | Auto-retrain disabled | |--------------+---------------------------------------------| | %E1 | Auto-retrain enabled | +------------------------------------------------------------+ +------------------------------------------------------------+ | COMPRESSION | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] %Cn [cmds] | |--------------+---------------------------------------------| | Description: | Selects data compression | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | %C0 | Data compression disabled | |--------------+---------------------------------------------| | %C1 | MNP5 enabled | +------------------------------------------------------------+ +------------------------------------------------------------+ | CONNECT MODE | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] \Nn [cmds] | |--------------+---------------------------------------------| | Description: | Controls the type of connection the modem | | | will operate in | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | \N0 | Normal mode enabled | |--------------+---------------------------------------------| | \N1 | Normal mode enabled | |--------------+---------------------------------------------| | \N2 | Reliable mode enabled | |--------------+---------------------------------------------| | \N3 | Auto-reliable mode enabled | |--------------+---------------------------------------------| | \N4 | V.42 reliable mode enabled | +------------------------------------------------------------+ +------------------------------------------------------------+ | DATA MODEM CALLING TONE | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] -Cn [cmds] | |--------------+---------------------------------------------| | Description: | Sets the data modem calling tone | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | -C0 | Calling tone disabled | |--------------+---------------------------------------------| | -C1 | 1300-Hz calling tone enabled | |--------------+---------------------------------------------| | -C2 | V.8 calling tone and 1300-Hz calling tone | +------------------------------------------------------------+ +------------------------------------------------------------+ | FLOW CONTROL TYPE | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] \Qn [cmds] | |--------------+---------------------------------------------| | Description: | Sets type of flow control used by modem | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | \Q0 | Flow control disabled | |--------------+---------------------------------------------| | \Q1 | XON/XOFF flow control enabled | |--------------+---------------------------------------------| | \Q2 | Uni-directional hardware flow control | | | enabled | |--------------+---------------------------------------------| | \Q3 | Bidirectional hardware flow control enabled | +------------------------------------------------------------+ +------------------------------------------------------------+ | INACTIVITY TIMER | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] \Tn [cmds] | |--------------+---------------------------------------------| | Default: | 0 | |--------------+---------------------------------------------| | Range: | 0-90 | |--------------+---------------------------------------------| | Unit: | 1 second | |--------------+---------------------------------------------| | Description: | Sets the length of time that the modem does | | | not receive information before it | | | disconnects. | +------------------------------------------------------------+ +------------------------------------------------------------+ | V.42bis - MAXIMUM STRING LENGTH | |------------------------------------------------------------| | Type: | Immediate | |--------------+---------------------------------------------| | Format: | AT [cmds] "On [cmds] | |--------------+---------------------------------------------| | Default: | 32 | |--------------+---------------------------------------------| | Range: | 6-250 | |--------------+---------------------------------------------| | Unit: | Characters | |--------------+---------------------------------------------| | Description: | Selects string size for V.42bis compression | +------------------------------------------------------------+ AT# VOICE COMMAND SET +------------------------------------------------------------+ | BEEP TONE | |------------------------------------------------------------| | Format: | AT [cmds] +VTD=n [cmds] | |--------------+---------------------------------------------| | Default: | 100 | |--------------+---------------------------------------------| | Range: | 5-255 | |--------------+---------------------------------------------| | Description: | Sets the beep tone duration timer | +------------------------------------------------------------+ +------------------------------------------------------------+ | BUFFER THRESHOLD | |------------------------------------------------------------| | Type: | Immediate | |--------------+---------------------------------------------| | Format: | AT [cmds] +VBT=n [cmds] | |--------------+---------------------------------------------| | Default: | 192, 320 | |--------------+---------------------------------------------| | Range: | 192, 320 | |--------------+---------------------------------------------| | Description: | Sets the buffer threshold | +------------------------------------------------------------+ +------------------------------------------------------------+ | CALLER ID | |------------------------------------------------------------| | Format: | AT [cmds] +VCID=n [cmds] | |--------------+---------------------------------------------| | Default: | 0 | |--------------+---------------------------------------------| | Range: | 0-2 | |--------------+---------------------------------------------| | Description: | Sets the caller ID | +------------------------------------------------------------+ +------------------------------------------------------------+ | COMPRESSION METHOD | |------------------------------------------------------------| | Format: | AT [cmds] +VSM=n [cmds] | |--------------+---------------------------------------------| | Default: | 140 (8-bit cirrus A-law) | | | | | | 8000 (used by some BBS) | | | | | | 0 (transmission disabled) | | | | | | 0 (DCE disabled) | |--------------+---------------------------------------------| | Description: | Sets the compression method | +------------------------------------------------------------+ +------------------------------------------------------------+ | FLOW CONTROL SELECT | |------------------------------------------------------------| | Type: | Immediate | |--------------+---------------------------------------------| | Format: | AT [cmds] +FLO=n [cmds] | |--------------+---------------------------------------------| | Default: | 1 | |--------------+---------------------------------------------| | Range: | 0-2 | |--------------+---------------------------------------------| | Description: | Selects the flow control | +------------------------------------------------------------+ +------------------------------------------------------------+ | HANG-UP CONTROL | |------------------------------------------------------------| | Format: | AT [cmds] +VNH=n [cmds] | |--------------+---------------------------------------------| | Default: | 0 | |--------------+---------------------------------------------| | Range: | 0-2 | |--------------+---------------------------------------------| | Description: | Controls the automatic hang-up | +------------------------------------------------------------+ +------------------------------------------------------------+ | INACTIVITY TIMER | |------------------------------------------------------------| | Format: | AT [cmds] +VIT=n [cmds] | |--------------+---------------------------------------------| | Default: | 0 | |--------------+---------------------------------------------| | Range: | 0-255 | |--------------+---------------------------------------------| | Description: | Sets the DTE/DEC inactivity timer | +------------------------------------------------------------+ +------------------------------------------------------------+ | INITIALIZE PARAMETER | |------------------------------------------------------------| | Format: | AT [cmds] +VIP [cmds] | |--------------+---------------------------------------------| | Description: | Initialize parameter | +------------------------------------------------------------+ +------------------------------------------------------------+ | SILENCE DETECTION | |------------------------------------------------------------| | Format: | AT [cmds] +VCSD=n [cmds] | |--------------+---------------------------------------------| | Default: | 0 | |--------------+---------------------------------------------| | Range: | 0, 1 | |--------------+---------------------------------------------| | Description: | Sets the voice command mode silence | | | detection | +------------------------------------------------------------+ +------------------------------------------------------------+ | DISTINCTIVE RING | |------------------------------------------------------------| | Format: | AT [cmds] +VDR=n [cmds] | |--------------+---------------------------------------------| | Default: | 0, 0 | |--------------+---------------------------------------------| | Range: | 0-255, 0-255 | |--------------+---------------------------------------------| | Description: | Sets the distinctive ring | +------------------------------------------------------------+ +------------------------------------------------------------+ | MICROPHONE GAIN | |------------------------------------------------------------| | Format: | AT [cmds] +VGM=n [cmds] | |--------------+---------------------------------------------| | Default: | 128 | |--------------+---------------------------------------------| | Range: | 121-131 | |--------------+---------------------------------------------| | Description: | Sets the microphone gain | +------------------------------------------------------------+ +------------------------------------------------------------+ | PLAY MODE | |------------------------------------------------------------| | Format: | AT [cmds] +VTX [cmds] | |--------------+---------------------------------------------| | Description: | Sets the play mode | +------------------------------------------------------------+ +------------------------------------------------------------+ | RECEIVE GAIN | |------------------------------------------------------------| | Format: | AT [cmds] +VGR=n [cmds] | |--------------+---------------------------------------------| | Default: | 128 | |--------------+---------------------------------------------| | Range: | 121-131 | |--------------+---------------------------------------------| | Description: | Sets the receive gain | +------------------------------------------------------------+ +------------------------------------------------------------+ | RECORD MODE | |------------------------------------------------------------| | Format: | AT [cmds] +VRX [cmds] | |--------------+---------------------------------------------| | Description: | Sets the record mode | +------------------------------------------------------------+ +------------------------------------------------------------+ | RELAY/SPEAKER CONTROL | |------------------------------------------------------------| | Format: | AT [cmds] +VGS=n [cmds] | |--------------+---------------------------------------------| | Default: | 0 | |--------------+---------------------------------------------| | Range: | 0-16 | |--------------+---------------------------------------------| | Description: | Stes the relay/speaker control | +------------------------------------------------------------+ +------------------------------------------------------------+ | REPORTING AND MASKING | |------------------------------------------------------------| | Format: | AT [cmds] +VEM=n [cmds] | |--------------+---------------------------------------------| | Default: | 'C', BB860980, BFE63883, BB863EE0 | |--------------+---------------------------------------------| | Description: | Controls the event reporting and masking | +------------------------------------------------------------+ +------------------------------------------------------------+ | RINGBACK TIMER | |------------------------------------------------------------| | Format: | AT [cmds] +VRA=n [cmds] | |--------------+---------------------------------------------| | Default: | 50 | |--------------+---------------------------------------------| | Range: | 0-50 | |--------------+---------------------------------------------| | Description: | Sets the ringback-goes-away timer | +------------------------------------------------------------+ +------------------------------------------------------------+ | RINGBACK TIMER | |------------------------------------------------------------| | Format: | AT [cmds] +VRN=n [cmds] | |--------------+---------------------------------------------| | Default: | 10 | |--------------+---------------------------------------------| | Range: | 0-255 | |--------------+---------------------------------------------| | Description: | Sets the ringback-never-appeared timer | +------------------------------------------------------------+ +------------------------------------------------------------+ | SILENCE DETECTION | |------------------------------------------------------------| | Format: | AT [cmds] +VSD=n [cmds] | |--------------+---------------------------------------------| | Default: | 128 (nominal) | | | | | | 50 (silence detection enabled) | |--------------+---------------------------------------------| | Description: | Sets silence detection | +------------------------------------------------------------+ +------------------------------------------------------------+ | VOICE MODE SELECTION | |------------------------------------------------------------| | Type: | Immediate | |--------------+---------------------------------------------| | Format: | AT [cmds] +FCLASS=n [cmds] | |--------------+---------------------------------------------| | Default: | 0 | |--------------+---------------------------------------------| | Range: | 0, 1, 8, 80 | |--------------+---------------------------------------------| | Description: | Sets the voice mode | +------------------------------------------------------------+ +------------------------------------------------------------+ | VOLUME SELECTION | |------------------------------------------------------------| | Format: | AT [cmds] +VGT=n [cmds] | |--------------+---------------------------------------------| | Default: | 128 | |--------------+---------------------------------------------| | Range: | 121-131 | |--------------+---------------------------------------------| | Description: | Selects the volume | +------------------------------------------------------------+ +------------------------------------------------------------+ | SPEAKERPHONE SELECTION | |------------------------------------------------------------| | Format: | AT [cmds] +VSP=n [cmds] | |--------------+---------------------------------------------| | Default: | 0 | |--------------+---------------------------------------------| | Range: | 0, 1 | |--------------+---------------------------------------------| | Description: | Controls the speakerphone | +------------------------------------------------------------+ +------------------------------------------------------------+ | SPEAKER PHONE TYPE | |------------------------------------------------------------| | Format: | AT [cmds] #VSPS=n [cmds] | |--------------+---------------------------------------------| | Default: | 0 | |--------------+---------------------------------------------| | Range: | 0, 1 | |--------------+---------------------------------------------| | Description: | Sets the speakerphone type | +------------------------------------------------------------+ +------------------------------------------------------------+ | TONE GENERATION | |------------------------------------------------------------| | Format: | AT [cmds] +VTS=n [cmds] | |--------------+---------------------------------------------| | Description: | Sets the DTMF and tone generation | +------------------------------------------------------------+