E-TECH RESEARCH, INC. ===================== PC56RVP Card Type Modem (asynchronous) Chipset Unidentified I/O Options Voice, speakerphone, DVSD, speaker out, microphone in Maximum Data Rate 56Kbps Maximum Fax Rate 14.4Kbps Data Modulation Bell 103A, 212A ITU-T V.21, V.22, V.22bis, V.23, V.32, V.32bis, V.34 Rockwell K56flex Fax Modulation ITU-T V.17, V.21CH2, V.27ter, V.29 Error MNP5, V.42, V.42bis Correction/Compression Fax Class Class I Data Bus 16-bit ISA Card Size Full height, half length +------------------------------------------------------------+ | CONNECTIONS | |------------------------------------------------------------| | Function | Label | Function | Label | |------------------------+-------+-------------------+-------| | Telephone line out | CN1 | Microphone in | CN3 | |------------------------+-------+-------------------+-------| | Telephone line in | CN2 | Speaker out | CN4 | +------------------------------------------------------------+ +------------------------------------------------------------+ | PLUG-N-PLAY CONFIGURATION | |------------------------------------------------------------| | Setting | JP1 | JP2 | JP3 | |----------+----------------+----------------+---------------| | Enabled | Pins 2 & 3 | Pins 2 & 3 | Pins 2 & 3 | | | closed | closed | closed | |----------+----------------+----------------+---------------| | Disabled | Pins 1 & 2 | Pins 1 & 2 | Pins 1 & 2 | | | closed | closed | closed | +------------------------------------------------------------+ +------------------------------------------------------------+ | SERIAL PORT ADDRESS SELECTION | |------------------------------------------------------------| | Setting | SW1/A | SW1/B | |--------------------+-------------------+-------------------| | 3F8h (COM1:) | Closed | Closed | |--------------------+-------------------+-------------------| | 2F8h (COM2:) | Open | Closed | |--------------------+-------------------+-------------------| | 3E8h (COM3:) | Closed | Open | |--------------------+-------------------+-------------------| | 2E8h (COM4:) | Open | Open | +------------------------------------------------------------+ +------------------------------------------------------------+ | INTERRUPT SELECTION | |------------------------------------------------------------| | Setting | SW1/C | SW1/D | SW1/E | SW1/F | |------------+-----------+-----------+-----------+-----------| | 3 | Closed | Open | Open | Open | |------------+-----------+-----------+-----------+-----------| | 4 | Open | Closed | Open | Open | |------------+-----------+-----------+-----------+-----------| | 5 | Open | Open | Closed | Open | |------------+-----------+-----------+-----------+-----------| | 7 | Open | Open | Open | Closed | +------------------------------------------------------------+ +------------------------------------------------------------+ | SUPPORTED STANDARD COMMANDS | |------------------------------------------------------------| | Basic AT Commands | |------------------------------------------------------------| | +++, 'comma', A/ | |------------------------------------------------------------| | A, B, D, E, H, L, M, N, O, P, Q, T, V, W, X, Y, Z | |------------------------------------------------------------| | &C, &D, &F, &G, &K, &P, &R, &S, &T, &V, &W, &Y, &Z | |------------------------------------------------------------| | Extended AT Commands | |------------------------------------------------------------| | \A, \N | |------------------------------------------------------------| | %C, %E, %L, %Q | |------------------------------------------------------------| | Special AT Commands | |------------------------------------------------------------| | :E, +MS | |------------------------------------------------------------| | S-Registers | |------------------------------------------------------------| | S0, S1, S2, S3, S4, S5, S6, S7, S8, S9, S10, S11, S12, | | S18, S24, S25, S26, S29, S30, S32, S33 | |------------------------------------------------------------| | S36, S38, S46, S48, S86, S91, S92, S95 | |------------------------------------------------------------| | Note: See MHI help file for complete information. | +------------------------------------------------------------+ +------------------------------------------------------------+ | UNIDENTIFIED COMMANDS | |------------------------------------------------------------| | Command | Default | |----------------------------+-------------------------------| | S28 | Unidentified | |----------------------------+-------------------------------| | S37 | Unidentified | |----------------------------+-------------------------------| | S41 | Unidentified | +------------------------------------------------------------+ Proprietary AT Command Set +------------------------------------------------------------+ | MODULATION SELECTION | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] +MS=x,y,z,a,b,c [cmds] | |--------------+---------------------------------------------| | Description: | Sets options for active protocol; the | | | transfer rates specified by z and a must be | | | valid for the protocol selected. | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | x=0 | Select V.21 protocol. | |--------------+---------------------------------------------| | x=1 | Select V.22 protocol. | |--------------+---------------------------------------------| | x=2 | Select V.22bis protocol. | |--------------+---------------------------------------------| | x=3 | Select V.23 protocol. | |--------------+---------------------------------------------| | x=9 | Select V.32 protocol. | |--------------+---------------------------------------------| | x=10 | Select V.32bis protocol. | |--------------+---------------------------------------------| | x=11 | Select V.34 protocol. | +------------------------------------------------------------+ +------------------------------------------------------------+ | MODULATION SELECTION (CON'T) | |------------------------------------------------------------| | Command | Function | |------------+-----------------------------------------------| | x=56 | Select K56flex protocol. | |------------+-----------------------------------------------| | x=64 | Select Bell 103 protocol. | |------------+-----------------------------------------------| | x=69 | Select Bell 212A protocol. | |------------+-----------------------------------------------| | y=0 | Modem will connect only with protocol and | | | speed selected. | |------------+-----------------------------------------------| | y=1 | Modem will auto-detect fastest common | | | protocol and speed. | |------------+-----------------------------------------------| | z, a=300 | Set minimum or maximum transfer rate at | | | 300bps, respectively. | |------------+-----------------------------------------------| | z, a=1200 | Set minimum or maximum transfer rate at | | | 1200bps, respectively. | |------------+-----------------------------------------------| | z, a=2400 | Set minimum or maximum transfer rate at | | | 2400bps, respectively. | |------------+-----------------------------------------------| | z, a=4800 | Set minimum or maximum transfer rate at | | | 4800bps, respectively. | |------------+-----------------------------------------------| | z, a=7200 | Set minimum or maximum transfer rate at | | | 7200bps, respectively. | |------------+-----------------------------------------------| | z, a=9600 | Set minimum or maximum transfer rate at | | | 9600bps, respectively. | |------------+-----------------------------------------------| | z, a=12000 | Set minimum or maximum transfer rate at | | | 12Kbps, respectively. | |------------+-----------------------------------------------| | z, a=14400 | Set minimum or maximum transfer rate at | | | 14.4Kbps, respectively. | |------------+-----------------------------------------------| | z, a=16800 | Set minimum or maximum transfer rate at | | | 16.8Kbps, respectively. | |------------+-----------------------------------------------| | z, a=19200 | Set minimum or maximum transfer rate at | | | 19.2Kbps, respectively. | |------------+-----------------------------------------------| | z, a=21600 | Set minimum or maximum transfer rate at | | | 21.6Kbps, respectively. | |------------+-----------------------------------------------| | z, a=24000 | Set minimum or maximum transfer rate at | | | 24Kbps, respectively. | |------------+-----------------------------------------------| | z, a=26400 | Set minimum or maximum transfer rate at | | | 26.4Kbps, respectively. | |------------+-----------------------------------------------| | z, a=28800 | Set minimum or maximum transfer rate at | | | 28.8Kbps, respectively. | |------------+-----------------------------------------------| | z, a=31200 | Set minimum or maximum transfer rate at | | | 31.2Kbps, respectively. | |------------+-----------------------------------------------| | z, a=32000 | Set minimum or maximum transfer rate at | | | 32Kbps, respectively; for K56flex mode. | |------------+-----------------------------------------------| | z, a=33600 | Set minimum or maximum transfer rate at | | | 33.6Kbps, respectively. | |------------+-----------------------------------------------| | z, a=34000 | Set minimum or maximum transfer rate at | | | 34Kbps, respectively; for K56flex mode. | |------------+-----------------------------------------------| | z, a=36000 | Set minimum or maximum transfer rate at | | | 36Kbps, respectively; for K56flex mode. | |------------+-----------------------------------------------| | z, a=38000 | Set minimum or maximum transfer rate at | | | 38Kbps, respectively; for K56flex mode. | |------------+-----------------------------------------------| | z, a=40000 | Set minimum or maximum transfer rate at | | | 40Kbps, respectively; for K56flex mode. | |------------+-----------------------------------------------| | z, a=42000 | Set minimum or maximum transfer rate at | | | 42Kbps, respectively; for K56flex mode. | |------------+-----------------------------------------------| | z, a=44000 | Set minimum or maximum transfer rate at | | | 44Kbps, respectively; for K56flex mode. | |------------+-----------------------------------------------| | z, a=46000 | Set minimum or maximum transfer rate at | | | 46Kbps, respectively; for K56flex mode. | |------------+-----------------------------------------------| | z, a=48000 | Set minimum or maximum transfer rate at | | | 48Kbps, respectively; for K56flex mode. | |------------+-----------------------------------------------| | z, a=50000 | Set minimum or maximum transfer rate at | | | 50Kbps, respectively; for K56flex mode. | |------------+-----------------------------------------------| | z, a=52000 | Set minimum or maximum transfer rate at | | | 52Kbps, respectively; for K56flex mode. | |------------+-----------------------------------------------| | z, a=54000 | Set minimum or maximum transfer rate at | | | 54Kbps, respectively; for K56flex mode. | |------------+-----------------------------------------------| | z, a=56000 | Set minimum or maximum transfer rate at | | | 56Kbps, respectively; for K56flex mode. | |------------+-----------------------------------------------| | b=0 | Mu-law codec enabled. | |------------+-----------------------------------------------| | b=1 | A-law codec enabled. | |------------+-----------------------------------------------| | c=0 | Robbed bit signaling detection disabled. | |------------+-----------------------------------------------| | c=1 | Robbed bit signaling detection enabled. | +------------------------------------------------------------+ See E-TECH RESEARCH, INC. PC336RVP for a full command summary.