CREATIX POLYMEDIA
=================

   PCMCIA 14.4 FAXMODEM

   Card Type              Modem (asynchronous)                    
   Chip Set               Unidentified                            
   Maximum Data Rate      14.4Kbps                                
   Maximum Fax Rate       14.4Kbps                                
   Data Bus               PCMCIA Type II                          
   Fax Class              Class I                                 
   Data Modulation        Bell 103A/212A                          
   Protocol                                                       
                          ITU-T V.21, V.22, V.22bis, V.23, V.32,  
                          V.32bis                                 
   Fax Modulation         ITU-T V.17, V.21CH2, V.27ter, V.29      
   Protocol               
   Error                  MNP5, V.42, V.42bis                     
   Correction/Compression 

                                                            V1892

                     Proprietary AT Command Set

   +------------------------------------------------------------+
   |            AUTO-RETRAIN - FALLBACK/FALLFORWARD             |
   |------------------------------------------------------------|
   | Type:        | Configuration                               |
   |--------------+---------------------------------------------|
   | Format:      | AT [cmds] %En [cmds]                        |
   |--------------+---------------------------------------------|
   | Description: | Controls auto-retrain mode and              |
   |              | fallback/fall forward                       |
   |--------------+---------------------------------------------|
   |   Command    |                  Function                   |
   |--------------+---------------------------------------------|
   |     %E0      | Auto-retrain disabled                       |
   |--------------+---------------------------------------------|
   |    i %E1     | Auto-retrain enabled                        |
   |--------------+---------------------------------------------|
   |     %E2      | Fallback/fall forward enabled               |
   |--------------+---------------------------------------------|
   |     %E3      | Auto-retrain enabled but modem will         |
   |              | disconnect if EQM reaches hang-up threshold |
   +------------------------------------------------------------+

   +------------------------------------------------------------+
   |                         BREAK SEND                         |
   |------------------------------------------------------------|
   | Type:        | Configuration                               |
   |--------------+---------------------------------------------|
   | Format:      | AT [cmds] \Bn [cmds]                        |
   |--------------+---------------------------------------------|
   | Default:     | 3                                           |
   |--------------+---------------------------------------------|
   | Range:       | Unidentified                                |
   |--------------+---------------------------------------------|
   | Unit:        | .1 second                                   |
   |--------------+---------------------------------------------|
   | Description: | Sends break to modem                        |
   +------------------------------------------------------------+

   +------------------------------------------------------------+
   |                         BREAK TYPE                         |
   |------------------------------------------------------------|
   | Type        | Configuration                                |
   |-------------+----------------------------------------------|
   | Format      | AT [cmds] \Kn [cmds]                         |
   |-------------+----------------------------------------------|
   | Default     | 5                                            |
   |-------------+----------------------------------------------|
   | Range       | 1-5                                          |
   |-------------+----------------------------------------------|
   | Description | Configures action of break signal            |
   +------------------------------------------------------------+

   +------------------------------------------------------------+
   |                        COMPRESSION                         |
   |------------------------------------------------------------|
   | Type:        | Configuration                               |
   |--------------+---------------------------------------------|
   | Format:      | AT %Cn                                      |
   |--------------+---------------------------------------------|
   | Description: | Selects data compression                    |
   |--------------+---------------------------------------------|
   |   Command    |                  Function                   |
   |--------------+---------------------------------------------|
   |     %C0      | Data compression disabled                   |
   |--------------+---------------------------------------------|
   |     %C1      | MNP5 enabled                                |
   |--------------+---------------------------------------------|
   |     %C2      | V.42bis enabled                             |
   |--------------+---------------------------------------------|
   |    i %C3     | MNP5 and V.42bis enabled                    |
   +------------------------------------------------------------+

   +------------------------------------------------------------+
   |                    COMPROMISE EQUALIZER                    |
   |------------------------------------------------------------|
   | Type:        | Configuration                               |
   |--------------+---------------------------------------------|
   | Format:      | AT [cmds] :En [cmds]                        |
   |--------------+---------------------------------------------|
   | Description: | Controls V.32 compromise equalizer          |
   |--------------+---------------------------------------------|
   |   Command    |                  Function                   |
   |--------------+---------------------------------------------|
   |     :E0      | Equalizer disabled                          |
   |--------------+---------------------------------------------|
   |    i :E1     | Equalizer enabled                           |
   +------------------------------------------------------------+

   +------------------------------------------------------------+
   |                        CONNECT MODE                        |
   |------------------------------------------------------------|
   | Type:        | Configuration                               |
   |--------------+---------------------------------------------|
   | Format:      | AT [cmds] \Nn [cmds]                        |
   |--------------+---------------------------------------------|
   | Description: | Sets connect mode                           |
   |--------------+---------------------------------------------|
   |   Command    |                  Function                   |
   |--------------+---------------------------------------------|
   |     \N0      | Normal mode enabled                         |
   |--------------+---------------------------------------------|
   |     \N1      | Direct mode enabled                         |
   |--------------+---------------------------------------------|
   |     \N2      | Reliable mode enabled                       |
   |--------------+---------------------------------------------|
   |    i \N3     | Auto-reliable mode enabled                  |
   |--------------+---------------------------------------------|
   |     \N4      | LAPM mode enabled                           |
   |--------------+---------------------------------------------|
   |     \N5      | MNP mode enabled                            |
   +------------------------------------------------------------+

   +------------------------------------------------------------+
   |                        FLOW CONTROL                        |
   |------------------------------------------------------------|
   | Type:        | Configuration                               |
   |--------------+---------------------------------------------|
   | Format:      | AT [cmds] \Gn [cmds]                        |
   |--------------+---------------------------------------------|
   | Description: | Selects modem port flow control             |
   |--------------+---------------------------------------------|
   |   Command    |                  Function                   |
   |--------------+---------------------------------------------|
   |    i \G0     | Flow control disabled                       |
   |--------------+---------------------------------------------|
   |     \G1      | Flow control enabled                        |
   +------------------------------------------------------------+

   +------------------------------------------------------------+
   |            MAXIMUM BLOCK SIZE FOR TRANSMISSION             |
   |------------------------------------------------------------|
   | Type:        | Configuration                               |
   |--------------+---------------------------------------------|
   | Format:      | AT [cmds] \An [cmds]                        |
   |--------------+---------------------------------------------|
   | Description: | Sets the maximum transmittable block size   |
   |--------------+---------------------------------------------|
   |   Command    |                  Function                   |
   |--------------+---------------------------------------------|
   |     \A0      | MNP block size is 64 characters             |
   |--------------+---------------------------------------------|
   |     \A1      | MNP block size is 128 characters            |
   |--------------+---------------------------------------------|
   |     \A2      | MNP block size is 192 characters            |
   |--------------+---------------------------------------------|
   |    i \A3     | MNP block size is 256 characters            |
   +------------------------------------------------------------+

   +------------------------------------------------------------+
   |                   MNP STREAM/BLOCK MODE                    |
   |------------------------------------------------------------|
   | Type:        | Configuration                               |
   |--------------+---------------------------------------------|
   | Format:      | AT [cmds] \Ln [cmds]                        |
   |--------------+---------------------------------------------|
   | Description: | Selects the transfer mode for MNP           |
   |--------------+---------------------------------------------|
   |   Command    |                  Function                   |
   |--------------+---------------------------------------------|
   |    i \L0     | Stream mode for MNP enabled                 |
   |--------------+---------------------------------------------|
   |     \L1      | Block mode for MNP enabled                  |
   +------------------------------------------------------------+

   +------------------------------------------------------------+
   |                     MNP10 COMPRESSION                      |
   |------------------------------------------------------------|
   | Type:        | Configuration                               |
   |--------------+---------------------------------------------|
   | Format:      | AT [cmds] -Kn [cmds]                        |
   |--------------+---------------------------------------------|
   | Description: | Selects MNP10 data compression from V.42    |
   |              | LAPM                                        |
   |--------------+---------------------------------------------|
   |   Command    |                  Function                   |
   |--------------+---------------------------------------------|
   |     -K0      | MNP10 disabled                              |
   |--------------+---------------------------------------------|
   |    i -K1     | MNP10 enabled                               |
   |--------------+---------------------------------------------|
   |     -K2      | MNP10 enabled on originate mode only        |
   +------------------------------------------------------------+

   +------------------------------------------------------------+
   |                       MNP10 FALLBACK                       |
   |------------------------------------------------------------|
   | Type:        | Configuration                               |
   |--------------+---------------------------------------------|
   | Format:      | AT [cmds] -Qn [cmds]                        |
   |--------------+---------------------------------------------|
   | Description: | Allows MNP10 to fallback to speeds slower   |
   |              | than 4800bps                                |
   |--------------+---------------------------------------------|
   |   Command    |                  Function                   |
   |--------------+---------------------------------------------|
   |     -Q0      | MNP10 at 2400 and 1200bps disabled          |
   |--------------+---------------------------------------------|
   |    i -Q1     | MNP10 at 2400 and 1200bps enabled           |
   +------------------------------------------------------------+

   +------------------------------------------------------------+
   |                   MNP10 LINK NEGOTIATION                   |
   |------------------------------------------------------------|
   | Type:        | Configuration                               |
   |--------------+---------------------------------------------|
   | Format:      | AT [cmds] *Hn [cmds]                        |
   |--------------+---------------------------------------------|
   | Description: | Sets the speed at which MNP10 link          |
   |              | negotiation will occur                      |
   |--------------+---------------------------------------------|
   |   Command    |                  Function                   |
   |--------------+---------------------------------------------|
   |    i *H0     | Link will be negotiated at highest possible |
   |              | speed                                       |
   |--------------+---------------------------------------------|
   |     *H1      | Link will be negotiated at 1200bps          |
   |--------------+---------------------------------------------|
   |     *H2      | Link will be negotiated at 4800bps          |
   +------------------------------------------------------------+

   +------------------------------------------------------------+
   |                  MNP10 POWER LEVEL ADJUST                  |
   |------------------------------------------------------------|
   | Type:        | Configuration                               |
   |--------------+---------------------------------------------|
   | Format:      | AT [cmds] )Mn [cmds]                        |
   |--------------+---------------------------------------------|
   | Description: | Controls automatic transmit power level     |
   |              | adjustment during MNP 10 link negotiation   |
   |--------------+---------------------------------------------|
   |   Command    |                  Function                   |
   |--------------+---------------------------------------------|
   |    i )M0     | Power level adjustment disabled             |
   |--------------+---------------------------------------------|
   |     )M1      | Power level adjustment enabled              |
   +------------------------------------------------------------+

   +------------------------------------------------------------+
   |                  REPORT LINE SIGNAL LEVEL                  |
   |------------------------------------------------------------|
   | Type:        | Immediate                                   |
   |--------------+---------------------------------------------|
   | Format:      | AT [cmds] %L [cmds]                         |
   |--------------+---------------------------------------------|
   | Description: | Returns received line signal level          |
   +------------------------------------------------------------+

   +------------------------------------------------------------+
   |                 REPORT LINE SIGNAL QUALITY                 |
   |------------------------------------------------------------|
   | Type:        | Immediate                                   |
   |--------------+---------------------------------------------|
   | Format:      | AT [cmds] %Q [cmds]                         |
   |--------------+---------------------------------------------|
   | Description: | Reports line signal quality                 |
   +------------------------------------------------------------+

   +------------------------------------------------------------+
   |                     TRANSMISSION LEVEL                     |
   |------------------------------------------------------------|
   | Type:        | Configuration                               |
   |--------------+---------------------------------------------|
   | Format:      | AT [cmds] @Mn [cmds]                        |
   |--------------+---------------------------------------------|
   | Default:     | 0                                           |
   |--------------+---------------------------------------------|
   | Range:       | 11-31                                       |
   |--------------+---------------------------------------------|
   | Unit:        | -1dBm                                       |
   |--------------+---------------------------------------------|
   | Description: | Sets the initial signal level for           |
   |              | transmission                                |
   |--------------+---------------------------------------------|
   |   Command    |                  Function                   |
   |--------------+---------------------------------------------|
   |     @M0      | -26dBm                                      |
   |--------------+---------------------------------------------|
   |     @M1      | -30dBm                                      |
   |--------------+---------------------------------------------|
   |   @M2-@M10   | -10dBm                                      |