ACTION WELL DEVELOPMENT, LTD. ============================= AC-5618 (REV. 1.0) Card Type Modem Chipset Unidentified I/O Options Audio in - CD-ROM, speaker connector, line in, line out, audio in, audio out, microphone in Maximum Modem Rate 56.0Kbps Maximum Fax Rate 14.4Kbps Fax Class Class I Modem Modulation Bell 103/212A Protocol ITU-T V.22bis,V.32, V.32bis, V.34, V.34bis, V.90 Fax Modulation ITU-T V.17 Protocol Error MNP5, V.42, V.42bis Correction/Compression Data Bus 16-bit ISA +------------------------------------------------------------+ | CONNECTIONS | |------------------------------------------------------------| | Function | Label | Function | Label | |------------------------------------------------------------| | Line in | CN1 | Audio out | CN5 | |-----------------------+---------+-------------------+------| | Line out | CN2 | Audio in - CD-ROM | CN6 | |-----------------------+---------+-------------------+------| | Microphone in | CN3 | Audio in - CD-ROM | CN7 | |-----------------------+---------+-------------------+------| | Audio in | CN4 | | | +------------------------------------------------------------+ +------------------------------------------------------------+ | SUPPORTED COMMAND SET | |------------------------------------------------------------| | Basic AT Commands | |------------------------------------------------------------| | AT, '+++', A/ | |------------------------------------------------------------| | A, E, H, M, O, P, Q, T, V | |------------------------------------------------------------| | &C, &P, &V, &W, &Z | |------------------------------------------------------------| | Extended AT Commands | |------------------------------------------------------------| | \A, \B, \N | |------------------------------------------------------------| | %C, %E | |------------------------------------------------------------| | S Registers | |------------------------------------------------------------| | S0, S1, S2, S3, S4, S5, S6, S7, S8, S9, S10, S11, S12 | |------------------------------------------------------------| | Special Commands | |------------------------------------------------------------| | +MS, #CID | |------------------------------------------------------------| | Voice Commands | |------------------------------------------------------------| | #TL, #VBT, #VRA, #VRX, #VSD, #VSP, #VSS, #VTD, #VTS, | | #VTX, #SPK | |------------------------------------------------------------| | Note: | See MHI Help File for full command documentation. | | | Further information on S-registers is currently | | | unavailable | +------------------------------------------------------------+ Proprietary AT Command Set +------------------------------------------------------------+ | AUTO-MODE DETECTION | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] Nn [cmds] | |--------------+---------------------------------------------| | Description: | Selects various options for the automatic | | | detection and negotiation of protocols | | | during the handshake process if the modem | | | is communicating with a remote modem of | | | dissimilar speed. | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | N0 | Auto-mode detection disabled. Handshake | | | begins at line speed designated by the S32 | | | register | |--------------+---------------------------------------------| | i N1 | Auto-mode detection enabled. Handshake | | | conducted according to the automode | | | algorithm supported by the modem | +------------------------------------------------------------+ +------------------------------------------------------------+ | COMMUNICATION PROTOCOLS | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] Bn [cmds] | |--------------+---------------------------------------------| | Description: | Selects the communication protocol for data | | | calls | |--------------+---------------------------------------------| | Command | Protocol | |--------------+---------------------------------------------| | B0 | ITU-T V.22 at 1200bps | +------------------------------------------------------------+ +------------------------------------------------------------+ | COMPRESSION | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] &Kn [cmds] | |--------------+---------------------------------------------| | Description: | Selects data compression | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | &K0 | Data compression disabled | |--------------+---------------------------------------------| | &K1 | MNP5 enabled | |--------------+---------------------------------------------| | &K2 | V.42bis enabled | |--------------+---------------------------------------------| | &K3 | MNP5 and V.42bis; or data compression and | | | correction enabled | +------------------------------------------------------------+ +------------------------------------------------------------+ | CONNECT MESSAGE SPEED SOURCE | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] &En [cmds] | |--------------+---------------------------------------------| | Description: | Selects source for speed field in CONNECT | | | message | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | i &E0 | DCE speed field | |--------------+---------------------------------------------| | &E1 | DTE speed field | +------------------------------------------------------------+ +------------------------------------------------------------+ | CONNECT MESSAGES | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] &An [cmds] | |--------------+---------------------------------------------| | Description: | Selects the format of CONNECT messages | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | i &A0 | CONNECT only | |--------------+---------------------------------------------| | &A1 | Modulation indicator added to CONNECT | | | message | |--------------+---------------------------------------------| | &A2 | Error detection and data compression | | | indicators added to CONNECT message | |--------------+---------------------------------------------| | &A3 | Modulation, error detection and data | | | compression indicators added to CONNECT | | | message | +------------------------------------------------------------+ +------------------------------------------------------------+ | DATA SET READY (DSR) | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] &Sn [cmds] | |--------------+---------------------------------------------| | Description: | Selects DSR options | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | &S0 | DSR forced high | |--------------+---------------------------------------------| | &S1 | DSR high only while modem is handshaking or | | | connected | +------------------------------------------------------------+ +------------------------------------------------------------+ | DATA TERMINAL READY (DTR) | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] &Dn [cmds] | |--------------+---------------------------------------------| | Description: | Selects modem response to DTR | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | i &D0 | DTR forced high | |--------------+---------------------------------------------| | &D1 | DTR toggle causes online command mode | |--------------+---------------------------------------------| | &D2 | Normal DTR operations | |--------------+---------------------------------------------| | &D3 | Resets on receipt of DTR | +------------------------------------------------------------+ +------------------------------------------------------------+ | DEFAULT CONFIGURATION | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] Yn [cmds] | |--------------+---------------------------------------------| | Description: | Selects the default user defined | | | configuration | |--------------+---------------------------------------------| | Note: | Does not load configuration | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | Y0 | Select user template 0 | |--------------+---------------------------------------------| | Y1 | Select user template 1 | |--------------+---------------------------------------------| | i Y2 | Select factory setting 0 | |--------------+---------------------------------------------| | Y3 | Select factory setting 1 | +------------------------------------------------------------+ +------------------------------------------------------------+ | DIAL | |------------------------------------------------------------| | Type: | Immediate | |--------------+---------------------------------------------| | Format: | AT [cmds] D<#> [cmds] | |--------------+---------------------------------------------| | Description: | Dials telephone number according to any | | | modifiers included in the string | |--------------+---------------------------------------------| | Note: | Any combination of modifiers can be used to | | | produce the desired dial functions in | | | sequence. | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | DL | Re-dial last number | |--------------+---------------------------------------------| | DP | Pulse dialing enabled | |--------------+---------------------------------------------| | DS=n | Dial stored telephone number n | |--------------+---------------------------------------------| | DT | Tone dialing enabled/Pulse dialing disabled | |--------------+---------------------------------------------| | DW | Dialing resumed following dial tone | | | detection | |--------------+---------------------------------------------| | D, | Dialing paused for amount of time specified | | | in S8 register | |--------------+---------------------------------------------| | D@ | Wait for Quite Answer function enabled. | | | Modem waits until a "quiet answer," a | | | ring-back signal followed by silence up to | | | the time specified in S7, is received prior | | | to executing the rest of the dial string. | |--------------+---------------------------------------------| | D! | Flash function initiated. Modem commanded | | | to go off-hook for specified time before | | | returning on-hook. | |--------------+---------------------------------------------| | D; | Modem returned to idle state after dialing. | | | The semicolon can only be placed at the end | | | of the dial command. | +------------------------------------------------------------+ +------------------------------------------------------------+ | FACTORY DEFAULT PROFILE | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] &Fn [cmds] | |--------------+---------------------------------------------| | Description: | Sets values in active profile to values | | | found in the default profile | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | i &F0 | Restore factory configuration 0 | |--------------+---------------------------------------------| | &F1 | Restore factory configuration 1 | +------------------------------------------------------------+ +------------------------------------------------------------+ | FLOW CONTROL | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] &Hn [cmds] | |--------------+---------------------------------------------| | Description: | Enables/disables flow control | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | &H0 | Flow control disabled | |--------------+---------------------------------------------| | i &H1 | RTS to CTS flow control enabled | +------------------------------------------------------------+ +------------------------------------------------------------+ | REPORT INFORMATION | |------------------------------------------------------------| | Type: | Immediate | |--------------+---------------------------------------------| | Format: | AT [cmds] In [cmds] | |--------------+---------------------------------------------| | Description: | Displays information requested | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | I1 | Reports manufacturer and model name | |--------------+---------------------------------------------| | I2 | Reports software version and provider | |--------------+---------------------------------------------| | I3 | Reports vendor/chip ID | |--------------+---------------------------------------------| | I4 | Reports stored and active profile | |--------------+---------------------------------------------| | I5 | Reports stored and active profile | |--------------+---------------------------------------------| | I6 | Reports stored and active profile | |--------------+---------------------------------------------| | I7 | Reports stored telephone numbers | +------------------------------------------------------------+ +------------------------------------------------------------+ | RTS/CTS | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] &Rn [cmds] | |--------------+---------------------------------------------| | Description: | Selects RTS/CTS options | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | &R0 | RTS is ignored | |--------------+---------------------------------------------| | &R1 | Modem recieves data only on RTS | +------------------------------------------------------------+ +------------------------------------------------------------+ | SELECT CALL PROGRESS RESULT CODES | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] Xn [cmds] | |--------------+---------------------------------------------| | Description: | Enables selection of tone detection and | | | associated result code format options | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | X0 | Busy and dial tone detection disabled; | | | result codes 0 - 4 enabled. | |--------------+---------------------------------------------| | X1 | Busy and dial tone detection disabled; | | | result codes 0 - 5 & 9 - 1212 enabled. | |--------------+---------------------------------------------| | X2 | Busy tone detection disabled, dial tone | | | detection enabled; result codes 0 - 6 & | | | | | | 9 - 1212 enabled. | |--------------+---------------------------------------------| | X3 | Busy tone detection enabled, dial tone | | | detection disabled; result codes 0 - 5, | | | | | | 7 - 1212 enabled. | |--------------+---------------------------------------------| | X4 | Busy and dial tone detection enabled; | | | result codes 0 - 1212 enabled. | +------------------------------------------------------------+ +------------------------------------------------------------+ | SOFT RESET | |------------------------------------------------------------| | Type: | Immediate | |--------------+---------------------------------------------| | Format: | AT [cmds] Zn [cmds] | |--------------+---------------------------------------------| | Description: | Restores modem profiles previously saved in | | | non-volatile RAM | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | Z0 | Restore default user template as defined by | | | Yn | |--------------+---------------------------------------------| | Z1 | Restore user template 0 | |--------------+---------------------------------------------| | Z2 | Restore user template 1 | |--------------+---------------------------------------------| | Z3 | Restore factory setting 0 | |--------------+---------------------------------------------| | Z4 | Restore factory setting 1 | +------------------------------------------------------------+ +------------------------------------------------------------+ | SPEAKER VOLUME | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] Ln [cmds] | |--------------+---------------------------------------------| | Description: | Controls speaker volume | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | L0 | Low volume setting | |--------------+---------------------------------------------| | L1 | Low volume setting | |--------------+---------------------------------------------| | i L2 | Medium volume setting | |--------------+---------------------------------------------| | L3 | Highest volume setting | +------------------------------------------------------------+ +------------------------------------------------------------+ | TEST MODES | |------------------------------------------------------------| | Type: | Immediate | |--------------+---------------------------------------------| | Format: | AT [cmds] &Tn | |--------------+---------------------------------------------| | Description: | Selects test options | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | i &T0 | TBD | |--------------+---------------------------------------------| | &T1 | TBD | |--------------+---------------------------------------------| | &T2 | TBD | |--------------+---------------------------------------------| | &T3 | TBD | +------------------------------------------------------------+ EXTENDED AT COMMAND SET +------------------------------------------------------------+ | BREAK TYPE | |------------------------------------------------------------| | Type: | Configuration | |-------------------+----------------------------------------| | Format: | AT [cmds] \Kn [cmds] | |-------------------+----------------------------------------| | Description: | Configures action of break signal | |------------------------------------------------------------| | Command | Function | |------------+-----------------------------------------------| | \K0 | Online command mode enabled, send no break to | | | remote modem | |------------+-----------------------------------------------| | \K1 | Break sent to remote modem and buffered | | | cleared | |------------+-----------------------------------------------| | \K2 | Online command mode enabled, send no break to | | | remote modem | |------------+-----------------------------------------------| | \K3 | Send break to remote modem immediately | |------------+-----------------------------------------------| | \K4 | Online command mode enabled, send no break to | | | remote modem | |------------+-----------------------------------------------| | i \K5 | Send break with transmitted data | +------------------------------------------------------------+ VOICE COMMANDS +------------------------------------------------------------+ | INACTIVITY TIMER | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] #VIT=n [cmds] | |--------------+---------------------------------------------| | Range: | 0-255 | |--------------+---------------------------------------------| | Unit: | .1ms | |--------------+---------------------------------------------| | Description: | Maximum duration of voice inactivity | | | allowed prior to initiating hang-up | | | process. | +------------------------------------------------------------+ +------------------------------------------------------------+ | MODE SELECTION | |------------------------------------------------------------| | Type: | Immediate | |--------------+---------------------------------------------| | Format: | AT [cmds] #CLS=n [cmds] | |--------------+---------------------------------------------| | Description: | Selects which mode the modem will operate | | | in. | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | #CLS=0 | Modem will operate in data mode. | |--------------+---------------------------------------------| | #CLS=1 | Modem will operate in fax class I mode. | |--------------+---------------------------------------------| | #CLS=8 | Modem will operate in voice mode. | +------------------------------------------------------------+ +------------------------------------------------------------+ | RECORD GAIN | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] #RG=hhhh [cmds] | |--------------+---------------------------------------------| | Range: | 0000 - 7FFF | |--------------+---------------------------------------------| | Unit: | Unidentified (hexadecimal) | |--------------+---------------------------------------------| | Description: | Sets the record gain. #RG? queries value | +------------------------------------------------------------+ +------------------------------------------------------------+ | VOICE - LOCAL SERIAL PORT SPEED | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] #BDR=n [cmds] | |--------------+---------------------------------------------| | Range: | 0-48 | |--------------+---------------------------------------------| | Unit: | 2400bps | |--------------+---------------------------------------------| | Description: | Sets the speed of the local serial port | | | when in voice mode. | +------------------------------------------------------------+ +------------------------------------------------------------+ | VOICE DEVICE | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] #VLS=n [cmds] | |--------------+---------------------------------------------| | Description: | Selects the I/O device for the DSP chip. | |--------------+---------------------------------------------| | Note: | VLS? Queries current setting. #VLS=? | | | Command will display the available options. | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | i #VLS=0 | Telephone line and handset used for voice | | | I/O. | |--------------+---------------------------------------------| | #VLS=2 | Internal speaker only used for voice I/O. | |--------------+---------------------------------------------| | #VLS=3 | External microphone only used for voice | | | I/O. | |--------------+---------------------------------------------| | #VLS=4 | Telephone line and handset used for voice | | | I/O; internal speaker enabled. | |--------------+---------------------------------------------| | #VLS=6 | Speakerphone used for voice I/O. | +------------------------------------------------------------+ +------------------------------------------------------------+ | VOICE PARAMETERS | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] #VIP [cmds] | |--------------+---------------------------------------------| | Description: | Initializes voice parameters | +------------------------------------------------------------+ +------------------------------------------------------------+ | VOICE RING DETECT TIME | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] #VRN=n [cmds] | |--------------+---------------------------------------------| | Default: | Unidentified | |--------------+---------------------------------------------| | Range: | 0-255 | |--------------+---------------------------------------------| | Unit: | .1ms | |--------------+---------------------------------------------| | Description: | Sets the maximum time the modem will wait | | | for the remote station to ring before it | | | assumes that it went off-hook before it | | | rang. | +------------------------------------------------------------+ +------------------------------------------------------------+ | VOICE SAMPLE QUALITY | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] #VBS=n [cmds] | |--------------+---------------------------------------------| | Description: | Selects the number of bits per sample that | | | the modem records. | |--------------+---------------------------------------------| | Note: | This modem may not support all options | | | listed below. The #VBS? Command will | | | display the available options. | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | #VBS=2 | Modem records 2 bits per sample in ADPCM | | | encoding. | |--------------+---------------------------------------------| | #VBS=4 | Modem records 4 bits per sample in ADPCM | | | encoding. | |--------------+---------------------------------------------| | #VBS=8 | Modem records 8 bits per sample in PCM | | | encoding. | |--------------+---------------------------------------------| | #VBS=16 | Modem records 16 bits per sample in PCM | | | encoding. | +------------------------------------------------------------+ +------------------------------------------------------------+ | VOICE SAMPLING RATE | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] #VSR=n [cmds] | |--------------+---------------------------------------------| | Description: | Sets the sampling rate used when recording | | | voice signals. #VSR? queries settings | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | #VSR=7200 | Selects a sampling rate of 7.2KHz. | |--------------+---------------------------------------------| | #VSR=8000 | Selects a sampling rate of 8.0KHz. | +------------------------------------------------------------+ +------------------------------------------------------------+ | VOICE TIMING MARK | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] #VTM=n [cmds] | |--------------+---------------------------------------------| | Range: | 1-10 | |--------------+---------------------------------------------| | Unit: | 1ms | |--------------+---------------------------------------------| | Description: | Configures timing mark placement. | +------------------------------------------------------------+ +------------------------------------------------------------+ | VOICE VOLUME LEVEL | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] #VGT=n [cmds] | |--------------+---------------------------------------------| | Range: | 0-255 | |--------------+---------------------------------------------| | Description: | Sets the volume level when playing back | | | audio signals. | +------------------------------------------------------------+