ARCHTEK CORPORATION =================== 5634PEW Card Type Modem/Fax card Chip Set ESS Maximum Modem Rate 56Kbps Maximum Fax Rate 14.4Kbps Data Modulation Bell 103A/212A Protocol ITU-T V.21, V.22, V.22bis, V.32, V.32bis, V.34, V.90 Fax Modulation ITU-T V.17, V.27ter, V.29, V.21CH2 Protocol Error MNP5, V.42, V.42bis Correction/Compression Fax Class Class I Data Bus PCI +------------------------------------------------------------+ | CONNECTIONS | |------------------------------------------------------------| | Function | Label | Function | Label | |------------------------------------------------------------| | Line in (RJ-11) | CN1 | Line out (RJ-11) | CN2 | +------------------------------------------------------------+ +------------------------------------------------------------+ | SUPPORTED COMMAND SET | |------------------------------------------------------------| | Basic AT Commands | |------------------------------------------------------------| | AT, '+++', 'comma', A/ | |------------------------------------------------------------| | A, B, E, H, P, Q, T, V, W, X, Y, Z | |------------------------------------------------------------| | &C, &P, &V, &W, &Y, &Z | |------------------------------------------------------------| | Extended AT Commands | |------------------------------------------------------------| | \A, \G, \L | |------------------------------------------------------------| | %C | |------------------------------------------------------------| | S Registers | |------------------------------------------------------------| | S0, S1, S2, S3, S4, S5, S6, S7, S8, S9, S10, S11, S12, | | S14, S16, S21, S22, S29, S32, S33 | |------------------------------------------------------------| | | |------------------------------------------------------------| | Note: See MHI Help File for full command documentation. | +------------------------------------------------------------+ PROPRIETARY AT COMMAND SET +------------------------------------------------------------+ | AUTO-MODE DETECTION | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] Nn [cmds] | |--------------+---------------------------------------------| | Description: | Selects various options for the automatic | | | detection and negotiation of protocols | | | during the handshake process if the modem | | | is communicating with a remote modem of | | | dissimilar speed. | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | N0 | Auto-mode detection disabled | |--------------+---------------------------------------------| | i N1 | Auto-mode detection enabled | +------------------------------------------------------------+ +------------------------------------------------------------+ | AUXILIARY RELAY CONTROL | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] &Jn [cmds] | |--------------+---------------------------------------------| | Description: | Enables/disables A/A1 relay driver. Not for | | | use with RJ-11 phone lines | |--------------+---------------------------------------------| | Command | Jack Type | |--------------+---------------------------------------------| | i &J0 | Auxiliary relay is disabled | +------------------------------------------------------------+ +------------------------------------------------------------+ | COMMUNICATIONS MODE | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] &Mn [cmds] | |--------------+---------------------------------------------| | Description: | Selects communications mode | |--------------+---------------------------------------------| | Command | Mode | |--------------+---------------------------------------------| | &M0 | Asynchronous mode | +------------------------------------------------------------+ +------------------------------------------------------------+ | COMMUNICATIONS MODE | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] &Qn [cmds] | |--------------+---------------------------------------------| | Description: | Selects communications mode options | |--------------+---------------------------------------------| | Command | Mode | |--------------+---------------------------------------------| | &Q0 | Asynchronous mode, serial port speed | | | follows connect speed. | +------------------------------------------------------------+ +------------------------------------------------------------+ | DATA SET READY (DSR) | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] &Sn [cmds] | |--------------+---------------------------------------------| | Description: | Selects DSR options | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | &S0 | DSR forced high | +------------------------------------------------------------+ +------------------------------------------------------------+ | DATA TERMINAL READY (DTR) | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] &Dn [cmds] | |--------------+---------------------------------------------| | Description: | Selects modem response to DTR | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | i &D0 | DTR override | |--------------+---------------------------------------------| | &D1 | DTR toggle causes online command mode | |--------------+---------------------------------------------| | &D2 | DTR toggle causes modem to go on-hook | +------------------------------------------------------------+ +------------------------------------------------------------+ | DIAL | |------------------------------------------------------------| | Type: | Immediate | |--------------+---------------------------------------------| | Format: | AT [cmds] D<#> [cmds] | |--------------+---------------------------------------------| | Description: | Dials telephone number according to any | | | modifiers included in the string | |--------------+---------------------------------------------| | Note: | Any combination of modifiers can be used to | | | produce the desired dial functions in | | | sequence. | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | DL | Re-dial last number | |--------------+---------------------------------------------| | DP | Pulse dialing enabled | |--------------+---------------------------------------------| | DT | Tone dialing enabled/Pulse dialing disabled | |--------------+---------------------------------------------| | DW | Dialing resumed following dial tone | | | detection | |--------------+---------------------------------------------| | D, | Dialing paused for amount of time specified | | | in S8 register | |--------------+---------------------------------------------| | D! | Flash function initiated. Modem commanded | | | to go off-hook for specified time before | | | returning on-hook. | |--------------+---------------------------------------------| | D; | Modem returned to idle state after dialing. | | | The semicolon can only be placed at the end | | | of the dial command. | +------------------------------------------------------------+ +------------------------------------------------------------+ | FACTORY DEFAULT PROFILE | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] &Fn [cmds] | |--------------+---------------------------------------------| | Description: | Sets values in active profile to values | | | found in the default profile | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | &F0 | Restore stored profile 0 after warm reset | |--------------+---------------------------------------------| | &F1 | Restore stored profile 1 after warm reset | +------------------------------------------------------------+ +------------------------------------------------------------+ | FLOW CONTROL | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] &Kn [cmds] | |--------------+---------------------------------------------| | Description: | Enables flow control options | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | &K0 | Flow control disabled | |--------------+---------------------------------------------| | i &K3 | RTS/CTS flow control enabled | |--------------+---------------------------------------------| | &K4 | XON/XOFF flow control enabled | |--------------+---------------------------------------------| | &K5 | Transparent XON/XOFF flow control enabled | |--------------+---------------------------------------------| | &K6 | RTS/CTS & XON/XOFF flow control enabled | +------------------------------------------------------------+ +------------------------------------------------------------+ | LINE TYPE | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] &Ln [cmds] | |--------------+---------------------------------------------| | Description: | Command nonfunctional | |--------------+---------------------------------------------| | Command | Line Type | |--------------+---------------------------------------------| | &L0 | Returns OK | +------------------------------------------------------------+ +------------------------------------------------------------+ | ON-LINE | |------------------------------------------------------------| | Type: | Immediate | |---------------+--------------------------------------------| | Format: | AT [cmds] On [cmds] | |---------------+--------------------------------------------| | Description: | Controls on-line command (data | | | transmission) state options. | |------------------------------------------------------------| | Note: The O command must be placed at the end of the | | command string. | |------------------------------------------------------------| | Command | Function | |---------------+--------------------------------------------| | O0 | On-line command mode with no retraining | | | enabled | |---------------+--------------------------------------------| | O1 | On-line command mode with long retrain | | | sequence enabled | |---------------+--------------------------------------------| | O2 | On-line command mode with short retrain | | | sequence enabled | +------------------------------------------------------------+ +------------------------------------------------------------+ | REPORT INFORMATION | |------------------------------------------------------------| | Type: | Immediate | |--------------+---------------------------------------------| | Format: | AT [cmds] In [cmds] | |--------------+---------------------------------------------| | Description: | Displays information requested | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | I0 | Reports product code | |--------------+---------------------------------------------| | I1 | Reports hardware variation code | |--------------+---------------------------------------------| | I2 | Reports DSP firmware revision | |--------------+---------------------------------------------| | I3 | Reports modem firmware revision information | |--------------+---------------------------------------------| | I4 | Reports response programmed by modem | | | manufacturer | +------------------------------------------------------------+ +------------------------------------------------------------+ | SPEAKER MODE | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] Mn [cmds] | |--------------+---------------------------------------------| | Description: | Selects various speaker options | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | M0 | Speaker disabled | |--------------+---------------------------------------------| | M1 | Speaker enabled until carrier signal | | | detected | |--------------+---------------------------------------------| | M2 | Speaker enabled | +------------------------------------------------------------+ +------------------------------------------------------------+ | TEST MODES | |------------------------------------------------------------| | Type: | Immediate | |--------------+---------------------------------------------| | Format: | AT [cmds] &Tn | |--------------+---------------------------------------------| | Description: | Selects test options | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | i &T0 | End current test | |--------------+---------------------------------------------| | &T1 | Begin local analog loopback test | +------------------------------------------------------------+ +------------------------------------------------------------+ | TRANSMIT CARRIER | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] Cn [cmds] | |--------------+---------------------------------------------| | Description: | Controls the transmit carrier switching. | | | Command nonfunctional | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | C1 | Returns OK message | +------------------------------------------------------------+ EXTENDED AT COMMANDS +------------------------------------------------------------+ | CONNECT MODE | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] \Nn [cmds] | |--------------+---------------------------------------------| | Description: | Controls the type of connection the modem | | | will operate in | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | \N0 | Normal mode enabled | |--------------+---------------------------------------------| | \N1 | Normal mode enabled | |--------------+---------------------------------------------| | i \N2 | Reliable mode enabled | |--------------+---------------------------------------------| | \N3 | Auto-reliable mode enabled | |--------------+---------------------------------------------| | \N4 | V.42 reliable mode enabled | |--------------+---------------------------------------------| | \N5 | MNP reliable mode enabled | +------------------------------------------------------------+