ACTIONTEC ELECTRONICS, INC. =========================== DESKVOICE ADVANTAGE Card Type Modem, Fax Chip Set Unidentified Maximum Modem Rate 56Kbps Maximum Fax Rate 14.4Kbps Data Modulation Protocol Unidentified Fax Modulation Protocol Unidentified Error Correction/Compression Unidentified Fax Class Unidentified Data Bus 16-bit ISA Card Size Half-length, half-height card +------------------------------------------------------------+ | CONNECTIONS | |------------------------------------------------------------| | Function | Label | Function | Label | |------------------------------------------------------------| | Line out | CN1 | Line in | CN2 | +------------------------------------------------------------+ +------------------------------------------------------------+ | SUPPORTED COMMAND SET | |------------------------------------------------------------| | Basic AT Commands | |------------------------------------------------------------| | AT, '+++', A/ | |------------------------------------------------------------| | A, C, E, H, M, P, Q, T, W, Z | |------------------------------------------------------------| | &C, &G, &V, &Z | |------------------------------------------------------------| | Extended AT Commands | |------------------------------------------------------------| | \A, \B, \J, \K, \T, \X | |------------------------------------------------------------| | S Registers | |------------------------------------------------------------| | S0, S1, S2, S3, S4, S5, S6, S7, S8, S9, S10, S11, S12, | | S91, S92 | |------------------------------------------------------------| | Note: See MHI Help File for full command documentation. | +------------------------------------------------------------+ Proprietary AT Command Set +------------------------------------------------------------+ | AUTO-MODE DETECTION | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] Nn [cmds] | |--------------+---------------------------------------------| | Description: | Selects various options for the automatic | | | detection and negotiation of protocols | | | during the handshake process if the modem | | | is communicating with a remote modem of | | | dissimilar speed. | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | N0 | Auto-mode detection disabled | |--------------+---------------------------------------------| | i N1 | In originate mode, handshake begins at line | | | speed designated by the S37 register. Modem | | | can shift to a slower speed if necessary. | | | | | | In answer mode, handshake attempted with | | | the following protocols in order - V.FC, | | | V.32bis, V.32, V.22bis, V.22 or Bell 212, | | | V.21, and Bell 103 | +------------------------------------------------------------+ +------------------------------------------------------------+ | AUXILIARY RELAY | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] &Jn [cmds] | |--------------+---------------------------------------------| | Description: | Selects the auxiliary relay option | |--------------+---------------------------------------------| | Command | Mode | |--------------+---------------------------------------------| | i &J0 | Auxiliary relay never closed | +------------------------------------------------------------+ +------------------------------------------------------------+ | COMMUNICATION PROTOCOLS | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] Bn [cmds] | |--------------+---------------------------------------------| | Description: | Selects the communication protocol for data | | | calls | |------------------------------------------------------------| | Note: The B command allows the simultaneous selection | | of more than one suffix, enabling multiple protocols. | |------------------------------------------------------------| | Command | Protocol | |--------------+---------------------------------------------| | B0 | ITU-T V.22 at 1200bps | |--------------+---------------------------------------------| | B1 | Bell 212A at 1200bps | |--------------+---------------------------------------------| | B2 | Unselect V.23 reverse channel | |--------------+---------------------------------------------| | B3 | Unselect V.23 reverse channel | |--------------+---------------------------------------------| | B15 | V.21 at 300bps | |--------------+---------------------------------------------| | B16 | Bell 103J at 300bps | +------------------------------------------------------------+ +------------------------------------------------------------+ | COMMUNICATIONS MODE | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] &Mn [cmds] | |--------------+---------------------------------------------| | Description: | Selects communications mode | |--------------+---------------------------------------------| | Command | Mode | |--------------+---------------------------------------------| | i &M0 | Asynchronous mode | +------------------------------------------------------------+ +------------------------------------------------------------+ | COMMUNICATIONS MODE | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] &Qn [cmds] | |--------------+---------------------------------------------| | Description: | Selects communications mode options | |--------------+---------------------------------------------| | Command | Mode | |--------------+---------------------------------------------| | i &Q0 | Asynchronous mode, serial port speed | | | follows connect speed. | |--------------+---------------------------------------------| | &Q5 | Buffered error correction mode | |--------------+---------------------------------------------| | &Q6 | Buffered asynchronous mode | |--------------+---------------------------------------------| | &Q7 | Reserved | |--------------+---------------------------------------------| | &Q8 | MNP error control mode | |--------------+---------------------------------------------| | &Q9 | V.42 or MNP error control mode | +------------------------------------------------------------+ +------------------------------------------------------------+ | DATA SET READY (DSR) | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] &Sn [cmds] | |--------------+---------------------------------------------| | Description: | Selects DSR options | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | &S0 | DSR forced high | |--------------+---------------------------------------------| | i &S1 | DSR high only while modem is handshaking or | | | connected | +------------------------------------------------------------+ +------------------------------------------------------------+ | DATA TERMINAL READY (DTR) | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] &Dn [cmds] | |--------------+---------------------------------------------| | Description: | Selects modem response to DTR | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | i &D0 | Modem does not respond to DTR | |--------------+---------------------------------------------| | &D1 | Modem goes to command mode after DTR goes | | | is off | |--------------+---------------------------------------------| | &D2 | Modem goes to command mode and disconnects | | | (hangs up) after DTR goes off; Auto-Answer | | | is disabled. | |--------------+---------------------------------------------| | &D3 | Modem is initialized after DTR goes off | +------------------------------------------------------------+ +------------------------------------------------------------+ | DIAL | |------------------------------------------------------------| | Type: | Immediate | |--------------+---------------------------------------------| | Format: | AT [cmds] D<#> [cmds] | |--------------+---------------------------------------------| | Description: | Dials telephone number according to any | | | modifiers included in the string | |--------------+---------------------------------------------| | Note: | Any combination of modifiers can be used to | | | produce the desired dial functions in | | | sequence. | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | DL | Re-dial last number | |--------------+---------------------------------------------| | DP | Pulse dialing enabled | |--------------+---------------------------------------------| | DS=n | Dial stored telephone number n | |--------------+---------------------------------------------| | DT | Tone dialing enabled/Pulse dialing disabled | |--------------+---------------------------------------------| | DW | Dialing resumed following dial tone | | | detection | |--------------+---------------------------------------------| | D, | Dialing paused for amount of time specified | | | in S8 register | |--------------+---------------------------------------------| | D^ | Disable data calling tone transmission | |--------------+---------------------------------------------| | D! | Flash function initiated. Modem commanded | | | to go off-hook for specified time before | | | returning on-hook. | |--------------+---------------------------------------------| | D@ | Wait for Quite Answer function enabled. | | | Modem waits until a "quiet answer," a | | | ring-back signal followed by silence up to | | | the time specified in S7, is received prior | | | to executing the rest of the dial string. | |--------------+---------------------------------------------| | D$ | Wait for prompt tone detection function | | | enabled. Waits for prompt tone for amount | | | of time specified by the S7 command. | |--------------+---------------------------------------------| | D; | Modem returned to idle state after dialing. | | | The semicolon can only be placed at the end | | | of the dial command. | +------------------------------------------------------------+ +------------------------------------------------------------+ | FACTORY DEFAULT PROFILE | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] &F [cmds] | |--------------+---------------------------------------------| | Description: | Sets values in active profile to values | | | found in the default profile | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | i &F0 | Recall factory setting as active | | | configuration | +------------------------------------------------------------+ +------------------------------------------------------------+ | FLOW CONTROL | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] &Kn [cmds] | |--------------+---------------------------------------------| | Description: | Enables flow control options | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | &K0 | Flow control disabled | |--------------+---------------------------------------------| | &K1 | Reserved | |--------------+---------------------------------------------| | &K2 | Reserved | |--------------+---------------------------------------------| | i &K3 | RTS/CTS flow control enabled | |--------------+---------------------------------------------| | &K4 | XON/XOFF flow control enabled | +------------------------------------------------------------+ +------------------------------------------------------------+ | ON-LINE | |------------------------------------------------------------| | Type: | Immediate | |---------------+--------------------------------------------| | Format: | AT [cmds] On [cmds] | |---------------+--------------------------------------------| | Description: | Controls on-line command (data | | | transmission) state options. | |------------------------------------------------------------| | Note: The O command must be placed at the end of the | | command string. | |------------------------------------------------------------| | Command | Function | |---------------+--------------------------------------------| | O0 | On-line command mode with no retraining | | | enabled | |---------------+--------------------------------------------| | O1 | On-line command mode with retraining | | | enabled | |---------------+--------------------------------------------| | O3 | Issue rate renegotiation before returning | | | to online data mode | +------------------------------------------------------------+ +------------------------------------------------------------+ | PULSE DIALING RATIO | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] &Pn [cmds] | |--------------+---------------------------------------------| | Description: | Selects pulse dial make/break ratio | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | i &P0 | 39/61ms at 10pps (North America) | |--------------+---------------------------------------------| | &P1 | 33/67ms at 10pps (Europe) | |--------------+---------------------------------------------| | &P2 | 39/61ms at 20pps | +------------------------------------------------------------+ +------------------------------------------------------------+ | REPORT INFORMATION | |------------------------------------------------------------| | Type: | Immediate | |--------------+---------------------------------------------| | Format: | AT [cmds] In [cmds] | |--------------+---------------------------------------------| | Description: | Displays information requested | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | I0 | Reports modem firmware revision number and | | | speed | |--------------+---------------------------------------------| | I1 | Reports ROM checksum | |--------------+---------------------------------------------| | I2 | Tests and reports ROM checksum | |--------------+---------------------------------------------| | I3 | Reports the default speed and the | | | controller firmware version | |--------------+---------------------------------------------| | I4 | Reports data pump firmware version | |--------------+---------------------------------------------| | I5 | Reports the board ID: software version, | | | hardware version, and country ID | |--------------+---------------------------------------------| | I6 | Reports OK | |--------------+---------------------------------------------| | I7 | Reports OK | |--------------+---------------------------------------------| | I8 | Reports OK | |--------------+---------------------------------------------| | I9 | Reports country code | |--------------+---------------------------------------------| | I11 | Reports diagnostic information for the last | | | connection | +------------------------------------------------------------+ +------------------------------------------------------------+ | RESTORE PROFILE ON POWER-UP | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] &Yn [cmds] | |--------------+---------------------------------------------| | Description: | Restores a selected profile into the active | | | profile on power-up (hard reset) | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | &Y0 | Selects profile 0 on power-up | +------------------------------------------------------------+ +------------------------------------------------------------+ | RTS/CTS | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] &Rn [cmds] | |--------------+---------------------------------------------| | Description: | Selects RTS/CTS options | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | i &R0 | CTS follows RTS in data mode; RTS is | | | ignored in command mode. | +------------------------------------------------------------+ +------------------------------------------------------------+ | SELECT CALL PROGRESS RESULT CODES | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] Xn [cmds] | |--------------+---------------------------------------------| | Description: | Enables selection of tone detection and | | | associated result code format options | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | X0 | Busy and dial tone detection disabled; | | | result codes 0 - 4 enabled. | |--------------+---------------------------------------------| | X1 | Busy and dial tone detection disabled; | | | result codes 0 - 5 & 10 enabled. | |--------------+---------------------------------------------| | X2 | Busy tone detection disabled, dial tone | | | detection enabled; result codes 0 - 6 & 10 | | | enabled. | |--------------+---------------------------------------------| | X3 | Busy tone detection enabled, dial tone | | | detection disabled; result codes 0 - 5, 7 & | | | 10 enabled. | |--------------+---------------------------------------------| | d X4 | Busy and dial tone detection enabled; | | | result codes 0 - 7 & 10 enabled. | |--------------+---------------------------------------------| | X5 | Busy and dial tone detection enabled; | | | result codes 0 - 7 & 10 enabled. | |--------------+---------------------------------------------| | X6 | Busy and dial tone detection enabled; | | | result codes 0 - 7 & 10 enabled. | |--------------+---------------------------------------------| | X7 | Busy and dial tone detection enabled; | | | result codes 0 - 7 & 10 enabled. | +------------------------------------------------------------+ +------------------------------------------------------------+ | SPEAKER VOLUME | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] Ln [cmds] | |--------------+---------------------------------------------| | Description: | Controls speaker volume | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | L0 | Lowest volume setting | |--------------+---------------------------------------------| | L1 | Low volume setting | |--------------+---------------------------------------------| | i L2 | Medium volume setting | |--------------+---------------------------------------------| | L3 | Highest volume setting | +------------------------------------------------------------+ +------------------------------------------------------------+ | STORE ACTIVE PROFILE | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] &Wn [cmds] | |--------------+---------------------------------------------| | Description: | Writes the values for the active profile | | | into the non-volatile RAM | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | &W0 | Writes the active profile to stored profile | | | 0 | +------------------------------------------------------------+ Extended Result Codes +------------------------------------------------------------+ | BLACKLIST | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] %B [cmds] | |--------------+---------------------------------------------| | Description: | View numbers in blacklist | +------------------------------------------------------------+ +------------------------------------------------------------+ | COMPRESSION | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] %Cn [cmds] | |--------------+---------------------------------------------| | Description: | Selects data compression | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | %C0 | Data compression disabled | |--------------+---------------------------------------------| | %C1 | V.42bis and MNP5 enabled | +------------------------------------------------------------+ +------------------------------------------------------------+ | CONNECT MODE | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] \Nn [cmds] | |--------------+---------------------------------------------| | Description: | Controls the type of connection the modem | | | will operate in | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | \N0 | Normal mode enabled | |--------------+---------------------------------------------| | \N1 | Direct mode enabled | |--------------+---------------------------------------------| | \N2 | Reliable mode enabled | |--------------+---------------------------------------------| | \N3 | Auto-reliable mode enabled | |--------------+---------------------------------------------| | \N4 | V.42 reliable mode enabled | |--------------+---------------------------------------------| | \N5 | Auto-reliable mode enabled | |--------------+---------------------------------------------| | \N7 | Auto-reliable mode enabled | +------------------------------------------------------------+ +------------------------------------------------------------+ | DATA CALLING TONE | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] -Cn [cmds] | |--------------+---------------------------------------------| | Description: | Controls the data calling tone | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | -C0 | Disable data calling tone | |--------------+---------------------------------------------| | -C1 | Enable data calling tone | +------------------------------------------------------------+ +------------------------------------------------------------+ | DATA CALLING TONE | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] -V90=n [cmds] | |--------------+---------------------------------------------| | Description: | Controls the data calling tone | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | -V90 = 0 | V.90 disabled | |--------------+---------------------------------------------| | -V90 = 1 | Auto Rate | |--------------+---------------------------------------------| | -V90 = 2 | 28000bps | |--------------+---------------------------------------------| | -V90 = 3 | 29333bps | |--------------+---------------------------------------------| | -V90 = 4 | 30666bps | |--------------+---------------------------------------------| | -V90 = 5 | 32000bps | |--------------+---------------------------------------------| | -V90 = 6 | 33333bps | |--------------+---------------------------------------------| | -V90 = 7 | 34666bps | |--------------+---------------------------------------------| | -V90 = 8 | 36000bps | |--------------+---------------------------------------------| | -V90 = 9 | 37333bps | |--------------+---------------------------------------------| | -V90 = 10 | 38666bps | |--------------+---------------------------------------------| | -V90 = 11 | 40000bps | |--------------+---------------------------------------------| | -V90 = 12 | 41333bps | |--------------+---------------------------------------------| | -V90 = 13 | 42666bps | |--------------+---------------------------------------------| | -V90 = 14 | 44000bps | |--------------+---------------------------------------------| | -V90 = 15 | 45333bps | |--------------+---------------------------------------------| | -V90 = 16 | 46666bps | |--------------+---------------------------------------------| | -V90 = 17 | 48000bps | |--------------+---------------------------------------------| | -V90 = 18 | 49333bps | |--------------+---------------------------------------------| | -V90 = 19 | 50666bps | |--------------+---------------------------------------------| | -V90 = 20 | 52000bps | |--------------+---------------------------------------------| | -V90 = 21 | 53333bps | +------------------------------------------------------------+ +------------------------------------------------------------+ | EXTENDED RESULT CODES | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] \Vn [cmds] | |--------------+---------------------------------------------| | Description: | Selects extended result codes | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | \V0 | Extended result codes disabled | |--------------+---------------------------------------------| | \V1 | Extended result codes enabled | |--------------+---------------------------------------------| | \V2 | Extended result codes enabled | +------------------------------------------------------------+ +------------------------------------------------------------+ | FLOW CONTROL | |------------------------------------------------------------| | Type: | Configuration | |----------------+-------------------------------------------| | Format: | AT [cmds] \Gn [cmds] | |----------------+-------------------------------------------| | Description: | Selects modem port flow control | |------------------------------------------------------------| | Note: Command performs no function; included for | | compatibility only | +------------------------------------------------------------+ +------------------------------------------------------------+ | FLOW CONTROL TYPE | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] \Qn [cmds] | |--------------+---------------------------------------------| | Description: | Sets type of flow control used by modem | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | \Q0 | Flow control disabled | |--------------+---------------------------------------------| | \Q1 | Bidirectional XON/XOFF flow control enabled | |--------------+---------------------------------------------| | \Q2 | CTS flow control by DCE enabled | |--------------+---------------------------------------------| | \Q3 | Bidirectional RTS/CTS flow control enabled | +------------------------------------------------------------+ +------------------------------------------------------------+ | RING INDICATOR | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] \Rn [cmds] | |--------------+---------------------------------------------| | Description: | Controls the ring indicator signal | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | \R0 | Ring indicator signal is off after the | | | telephone call is answered | +------------------------------------------------------------+ S(status) -REGISTERS +------------------------------------------------------------+ | 56K DIAL LINE RATE | |------------------------------------------------------------| | Type: | Register | |--------------+---------------------------------------------| | Format | AT [cmds] S38=n [cmds] | |--------------+---------------------------------------------| | Description: | Sets the maximum allowable data exchange | | | rate attempted during handshake process. | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | i S38=0 | K56flex disabled | |--------------+---------------------------------------------| | S38=1 | K56flex autorate | |--------------+---------------------------------------------| | S38=2 | 32000bps | |--------------+---------------------------------------------| | S38=3 | 34000bps | |--------------+---------------------------------------------| | S38=4 | 36000bps | |--------------+---------------------------------------------| | S38=5 | 38000bps | |--------------+---------------------------------------------| | S38=6 | 40000bps | |--------------+---------------------------------------------| | S38=7 | 42000bps | |--------------+---------------------------------------------| | S38=8 | 44000bps | |--------------+---------------------------------------------| | S38=9 | 46000bps | |--------------+---------------------------------------------| | S38=10 | 48000bps | |--------------+---------------------------------------------| | S38=11 | 50000bps | |--------------+---------------------------------------------| | S38=12 | 52000bps | |--------------+---------------------------------------------| | S38=13 | 54000bps | |--------------+---------------------------------------------| | S38=14 | 56000bps | +------------------------------------------------------------+ +------------------------------------------------------------+ | BIT-MAPPED REGISTER S14 | |------------------------------------------------------------| | Format: | AT [cmds] S14=n [cmds] | |--------------+---------------------------------------------| | Default: | 8 | |--------------+---------------------------------------------| | Range: | 0-174 | |--------------+---------------------------------------------| | Unit: | Bit-mapped | |--------------+---------------------------------------------| | Description: | Controls echo, result codes and display and | | | dial mode | |--------------+---------------------------------------------| | Bit | Value | Function | |------+-------+---------------------------------------------| | 3 | 0 | Display result codes in numeric format | | | | | | | i 1 | Display result codes in verbose format | |------+-------+---------------------------------------------| | 6 | i 0 | 10 PPS | | | | | | | 1 | 20 PPS | +------------------------------------------------------------+ +------------------------------------------------------------+ | BIT-MAPPED REGISTER S21 | |------------------------------------------------------------| | Format | AT [cmds] S21=n [cmds] | |--------------+---------------------------------------------| | Default: | 48 | |--------------+---------------------------------------------| | Range: | Unidnetified | |--------------+---------------------------------------------| | Unit: | Bit-mapped | |--------------+---------------------------------------------| | Description: | Indicates the status of command options | |--------------+---------------------------------------------| | Bit | Value | Function | |------+-------+---------------------------------------------| | 4, 3 | 0 | &D0 selected | | | | | | | 1 | &D1 selected | | | | | | | 2 | &D2 selected | | | | | | | 3 | &D3 selected | |------+-------+---------------------------------------------| | 5 | 0 | &C0 selected | | | | | | | 1 | &C1 selected | +------------------------------------------------------------+ +------------------------------------------------------------+ | BIT-MAPPED REGISTER S22 | |------------------------------------------------------------| | Format | AT [cmds] S22=n [cmds] | |---------------+--------------------------------------------| | Default: | Unidentified | |---------------+--------------------------------------------| | Range: | 0-255 | |---------------+--------------------------------------------| | Unit: | Bit-mapped | |---------------+--------------------------------------------| | Description: | Indicates the status of command options | |---------------+--------------------------------------------| | Bit | Value | Function | |-------+-------+--------------------------------------------| | 6 - 4 | 0 | X0 selected | | | | | | | 4 | X1 selected | | | | | | | 5 | X2 selected | | | | | | | 6 | X3 selected | | | | | | | 7 | X4 selected | |-------+-------+--------------------------------------------| | 7 | 0 | 33/67ms at 10pps (Europe) | | | | | | | 1 | 39/61ms at 10pps (North America) | +------------------------------------------------------------+ +------------------------------------------------------------+ | BIT-MAPPED REGISTER S28 | |------------------------------------------------------------| | Format | AT [cmds] S28=n [cmds] | |--------------+---------------------------------------------| | Default: | unidentified | |--------------+---------------------------------------------| | Range: | 0-31 | |--------------+---------------------------------------------| | Unit: | Bit-mapped | |--------------+---------------------------------------------| | Description: | Controls V.23 split speed, transmit/receive | | | speed, half duplex; and pulse dialing. | |--------------+---------------------------------------------| | Value | Function | |--------------+---------------------------------------------| | 0 | Disable | |--------------+---------------------------------------------| | 1-255 | Enable | +------------------------------------------------------------+ +------------------------------------------------------------+ | BIT-MAPPED REGISTER S40 | |------------------------------------------------------------| | Format | AT [cmds] S40=n [cmds] | |--------------+---------------------------------------------| | Default: | 0 | |--------------+---------------------------------------------| | Range: | 0-2 | |--------------+---------------------------------------------| | Unit: | Bit-mapped | |--------------+---------------------------------------------| | Description: | Controls ETC startup autorating | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | i S40=0 | Startup with normal autorating | |--------------+---------------------------------------------| | S40=1 | Startup with initial rate of 4800 or below | |--------------+---------------------------------------------| | S40=2 | Startup with initial rate of 9600 or below | +------------------------------------------------------------+ +------------------------------------------------------------+ | DATA CALLING TONE | |------------------------------------------------------------| | Type: | Register | |--------------+---------------------------------------------| | Format | AT [cmds] S35n [cmds] | |--------------+---------------------------------------------| | Description: | Controls the data calling tone | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | S36=0 | Disabled | |--------------+---------------------------------------------| | S36=1 | Enabled | +------------------------------------------------------------+ +------------------------------------------------------------+ | DCE LINE SPEED | |------------------------------------------------------------| | Type: | Register | |--------------+---------------------------------------------| | Format | AT [cmds] S37=n [cmds] | |--------------+---------------------------------------------| | Description: | Sets the maximum allowable data exchange | | | rate attempted during handshake process. | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | i S37=0 | Speed of last connection | |--------------+---------------------------------------------| | S37=1 | Reserved | |--------------+---------------------------------------------| | S37=2 | 1200/75bps | |--------------+---------------------------------------------| | S37=3 | 300bps | |--------------+---------------------------------------------| | S37=4 | Reserved | |--------------+---------------------------------------------| | S37=5 | 1200bps | |--------------+---------------------------------------------| | S37=6 | 2400bps | |--------------+---------------------------------------------| | S37=7 | 4800bps | |--------------+---------------------------------------------| | S37=8 | 7200bps | |--------------+---------------------------------------------| | S37=9 | 9600bps | |--------------+---------------------------------------------| | S37=10 | 12000bps | |--------------+---------------------------------------------| | S37=11 | 14400bps | |--------------+---------------------------------------------| | S37=12 | 16800bps | |--------------+---------------------------------------------| | S37=13 | 19200bps | |--------------+---------------------------------------------| | S37=14 | 21600bps | |--------------+---------------------------------------------| | S37=15 | 24000bps | |--------------+---------------------------------------------| | S37=16 | 26400bps | |--------------+---------------------------------------------| | S37=17 | 28800bps | |--------------+---------------------------------------------| | S37=18 | 31200bps | |--------------+---------------------------------------------| | S37=19 | 33600bps | +------------------------------------------------------------+ +------------------------------------------------------------+ | FEATURE NEGOTIATION OPTIONS | |------------------------------------------------------------| | Type: | Register | |------------------------------------------------------------| | Format: | AT [cmds] S48=n [cmds] | |--------------+---------------------------------------------| | Description: | Selects active error correction and | | | compression protocols | |------------------------------------------------------------| | Command | Function | |---------------+--------------------------------------------| | i S48=7 | Detection negotiation and XID negotiation | | | enabled | |---------------+--------------------------------------------| | S48=128 | Detection negotiation and XID negotiation | | | disabled, fall-back to options set in S36 | +------------------------------------------------------------+ +------------------------------------------------------------+ | LOCAL PHONE STATUS | |------------------------------------------------------------| | Type: | Register | |---------------+--------------------------------------------| | Format: | AT [cmds] S90=n [cmds] | |---------------+--------------------------------------------| | Description: | Sets the status of the local phone | |------------------------------------------------------------| | Command | Function | |------------+-----------------------------------------------| | i S90=7 | Local phone on-hook | |------------+-----------------------------------------------| | S90=128 | Local phone off-hook | +------------------------------------------------------------+ +------------------------------------------------------------+ | NEGOTIATION FALLBACK | |------------------------------------------------------------| | Type: | Register | |--------------+---------------------------------------------| | Format | AT [cmds] S36=n [cmds] | |--------------+---------------------------------------------| | Description: | Controls the negotiation fallback | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | S36=0, 2 | Hang up | |--------------+---------------------------------------------| | S36=1, 3 | Attempt a direct connection | |--------------+---------------------------------------------| | S36=4, 6 | Attempt a connection at MNP2-4; if that | | | fails, hang up. | |--------------+---------------------------------------------| | S36=5, 7 | Attempt a connection at MNP2-4; if that | | | fails, attempt a direct connection. | +------------------------------------------------------------+ +------------------------------------------------------------+ | SLEEP MODE | |------------------------------------------------------------| | Type: | Register | |--------------+---------------------------------------------| | Format | AT [cmds] S89=n [cmds] | |--------------+---------------------------------------------| | Default: | 10 | |--------------+---------------------------------------------| | Range: | 0, 5-255 | |--------------+---------------------------------------------| | Description: | Controls the sleep mode timer | +------------------------------------------------------------+ +------------------------------------------------------------+ | SYNTHETIC RING FREQUENCY | |------------------------------------------------------------| | Type: | Register | |--------------+---------------------------------------------| | Format: | AT [cmds] S33=n [cmds] | |--------------+---------------------------------------------| | Default: | 0 | |--------------+---------------------------------------------| | Range: | 0-5 | |--------------+---------------------------------------------| | Unit: | Unidentified | |--------------+---------------------------------------------| | Description: | Specifies a synthetic ring frequency | +------------------------------------------------------------+ +------------------------------------------------------------+ | SYNTHETIC RING VOLUME | |------------------------------------------------------------| | Type: | Register | |--------------+---------------------------------------------| | Format: | AT [cmds] S32=n [cmds] | |--------------+---------------------------------------------| | Default: | 16 | |--------------+---------------------------------------------| | Range: | Unidentified | |--------------+---------------------------------------------| | Unit: | dB | |--------------+---------------------------------------------| | Description: | Specifies a synthetic ring volume with | | | implied minus sign | +------------------------------------------------------------+