APACHE MICRO PERIPHERALS, INC. ============================== APACHE A56SP-R Card Type Modem (asynchronous) Chip Set Unidentified I/O Options Speaker out, microphone, line in, line out Maximum Modem Rate 56Kbps Maximum Fax Rate 14.4Kbps Data Modulation Bell 103/212A Protocol ITU-T V.21, V.22bis, V.23, V.32, V.32bis, V.34, V.34+, V.FC, K56flex, V.90 Fax Modulation ITU-T V.17, V.21 CH2, V.27ter, V.29 Protocol Error MNP5, V.42, V.42bis Correction/Compression Fax Class Class I Data Bus 16-bit ISA Card Size Half-length, full-height card +------------------------------------------------------------+ | CONNECTIONS | |------------------------------------------------------------| | Function | Label | Function | Label | |------------------------------------------------------------| | Line out | CN1 | Microphone | CN3 | |----------------------------+----------+-------------+------| | Line in | CN2 | Speaker out | CN4 | +------------------------------------------------------------+ +------------------------------------------------------------+ | SERIAL PORT ADDRESS | |------------------------------------------------------------| | Setting | SW1/5 | SW1/6 | |--------------------+-------------------+-------------------| | COM1 (3F8h) | On | On | |--------------------+-------------------+-------------------| | COM2 (2F8h) | Off | On | |--------------------+-------------------+-------------------| | COM3 (3E8h) | On | Off | |--------------------+-------------------+-------------------| | COM4 (2E8h) | Off | Off | +------------------------------------------------------------+ +------------------------------------------------------------+ | INTERRUPT | |------------------------------------------------------------| | Setting | SW1/1 | SW1/2 | SW1/3 | SW1/4 | SW1/7 | JP1 | |---------+--------+--------+--------+-------+-------+-------| | IRQ 2 | Off | Off | Off | Off | On | Open | |---------+--------+--------+--------+-------+-------+-------| | IRQ 3 | Off | Off | Off | On | Off | Open | |---------+--------+--------+--------+-------+-------+-------| | IRQ 4 | Off | Off | On | Off | Off | Open | |---------+--------+--------+--------+-------+-------+-------| | IRQ 5 | Off | On | Off | Off | Off | Open | |---------+--------+--------+--------+-------+-------+-------| | IRQ 7 | On | Off | Off | Off | Off | Open | |---------+--------+--------+--------+-------+-------+-------| | IRQ 10 | Off | Off | Off | Off | Off | 2 & 3 | |---------+--------+--------+--------+-------+-------+-------| | IRQ 11 | Off | Off | Off | Off | Off | 1 & 2 | |------------------------------------------------------------| | Note: Pins designated are in the closed position | +------------------------------------------------------------+ +------------------------------------------------------------+ | SUPPORTED COMMAND SET | |------------------------------------------------------------| | Basic AT Commands | |------------------------------------------------------------| | AT, A/ | |------------------------------------------------------------| | A, B, D, E, H, M, O, P, Q, T, V, W, X, Y, Z | |------------------------------------------------------------| | &C, &D, &M, &P, &Q, &R, &T, &W, &X, &Y, &Z | |------------------------------------------------------------| | Extended AT Commands | |------------------------------------------------------------| | \A, \B, \K, \N | |------------------------------------------------------------| | %C, %E, %L, %Q | |------------------------------------------------------------| | S Registers | |------------------------------------------------------------| | S0, S1, S2, S3, S4, S5, S6, S7, S8, S9, S10, S11, S12, | | S14, S16, S18, S21, S22, S23, S24, S25, | |------------------------------------------------------------| | S26, S27, S28, S29, S30, S31, S32, S33, S36, S37, S38, | | S39, S40, S41, S46, S48, S82, S86, | |------------------------------------------------------------| | S91, S92, S95 | |------------------------------------------------------------| | Special Commands | |------------------------------------------------------------| | -K, +MS | |------------------------------------------------------------| | Note: See MHI Help File for full command documentation. | +------------------------------------------------------------+ Proprietary AT Command Set +------------------------------------------------------------+ | TRANSMIT CARRIER | |------------------------------------------------------------| | Type: | Configuration | |---------------+--------------------------------------------| | Format: | AT [cmds] Cn [cmds] | |---------------+--------------------------------------------| | Description: | Controls the transmit carrier switching | |------------------------------------------------------------| | Note: Disabling the transmit carrier puts the modem | | in receive-only mode | |------------------------------------------------------------| | Command | Function | |---------------+--------------------------------------------| | i C1 | Return OK message | +------------------------------------------------------------+ +------------------------------------------------------------+ | LINE MODULATION | |------------------------------------------------------------| | Type: | Configuration | |----------------------+-------------------------------------| | Format: | AT [cmds] Fn [cmds] | |----------------------+-------------------------------------| | Description: | Selects the line modulation | |------------------------------------------------------------| | Note: This command is only supported on older modems | |------------------------------------------------------------| | Command | Function | |----------------------+-------------------------------------| | F0 | Auto-detect mode | |----------------------+-------------------------------------| | i F1 | V.21 or Bell 103 | |----------------------+-------------------------------------| | F3 | V.23 | |----------------------+-------------------------------------| | F4 | V.22 or Bell 212A @ 1200bps | |----------------------+-------------------------------------| | F5 | V.22bis | |----------------------+-------------------------------------| | F6 | V.32bis or V.32 @ 4800bps | |----------------------+-------------------------------------| | F7 | V.32bis @ 7200bps | |----------------------+-------------------------------------| | F8 | V.32bis or V.32 @ 9600bps | |----------------------+-------------------------------------| | F9 | V.32bis @ 12000bps | |----------------------+-------------------------------------| | F10 | V.32bis @ 14400bps | +------------------------------------------------------------+ +------------------------------------------------------------+ | REPORT INFORMATION | |------------------------------------------------------------| | Type: | Immediate | |--------------+---------------------------------------------| | Format: | AT [cmds] In [cmds] | |--------------+---------------------------------------------| | Description: | Displays information requested | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | I0 | Reports product code | |--------------+---------------------------------------------| | I1 | Reports ROM checksum | |--------------+---------------------------------------------| | I2 | Reports OK | |--------------+---------------------------------------------| | I3 | Report firmware revision, model interface | | | type | |--------------+---------------------------------------------| | I4 | Reports response programmed by an OEM | |--------------+---------------------------------------------| | I5 | Reports country code | |--------------+---------------------------------------------| | I6 | Reports modem data pump model and code | | | revision | |--------------+---------------------------------------------| | I7 | Reports DAA code (W-class only) | +------------------------------------------------------------+ +------------------------------------------------------------+ | SPEAKER VOLUME | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] Ln [cmds] | |--------------+---------------------------------------------| | Description: | Controls speaker volume | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | L0 | Low volume setting | |--------------+---------------------------------------------| | L1 | Low volume setting | |--------------+---------------------------------------------| | i L2 | Medium volume setting | |--------------+---------------------------------------------| | L3 | Highest volume setting | +------------------------------------------------------------+ +------------------------------------------------------------+ | AUTO-MODE DETECTION | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] Nn [cmds] | |--------------+---------------------------------------------| | Description: | Selects various options for the automatic | | | detection and negotiation of protocols | | | during the handshake process if the modem | | | is communicating with a remote modem of | | | dissimilar speed. | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | N0 | Auto-mode detection disabled | |--------------+---------------------------------------------| | N1 | Auto-mode detection enabled | +------------------------------------------------------------+ +------------------------------------------------------------+ | FACTORY DEFAULT PROFILE | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] &F [cmds] | |--------------+---------------------------------------------| | Description: | Sets values in active profile to values | | | found in the default profile | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | i &F0 | Restore factory profile 0 | |--------------+---------------------------------------------| | &F1 | Restore factory profile 1 | +------------------------------------------------------------+ +------------------------------------------------------------+ | GUARD TONE | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] &Gn [cmds] | |--------------+---------------------------------------------| | Description: | Commands the modem to transmit a guard tone | | | in V.22/V.22bis | |------------------------------------------------------------| | Note: Used primarily for international data | | transmission | |------------------------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | i &G0 | Guard tone disabled | |--------------+---------------------------------------------| | &G1 | Guard tone disabled | |--------------+---------------------------------------------| | &G2 | 1800Hz guard tone enabled | +------------------------------------------------------------+ +------------------------------------------------------------+ | S-REGISTER RESPONSE | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] &Jn [cmds] | |--------------+---------------------------------------------| | Description: | This command included for compatibility. It | | | performs no function. | +------------------------------------------------------------+ +------------------------------------------------------------+ | FLOW CONTROL | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] &Kn [cmds] | |--------------+---------------------------------------------| | Description: | Enables flow control options | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | &K0 | Flow control disabled | |--------------+---------------------------------------------| | &K3 | RTS/CTS flow control enabled | |--------------+---------------------------------------------| | &K4 | XON/XOFF flow control enabled | |--------------+---------------------------------------------| | &K5 | Transparent XON/XOFF flow control enabled | |--------------+---------------------------------------------| | &K6 | RTS/CTS and XON/XOFF flow control enabled | +------------------------------------------------------------+ +------------------------------------------------------------+ | LINE TYPE | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] &Ln [cmds] | |--------------+---------------------------------------------| | Description: | Selects line type | |--------------+---------------------------------------------| | Command | Line Type | |--------------+---------------------------------------------| | i &L0 | Switched line (PSTN/Dial-up) | +------------------------------------------------------------+ +------------------------------------------------------------+ | DATA SET READY (DSR) | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] &Sn [cmds] | |--------------+---------------------------------------------| | Description: | Selects DSR options | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | &S0 | DSR forced high | |--------------+---------------------------------------------| | &S1 | DSR high while modem is handshaking or | | | connected | +------------------------------------------------------------+ +------------------------------------------------------------+ | CONFIGURATION PROFILES | |------------------------------------------------------------| | Type: | Immediate | |--------------+---------------------------------------------| | Format: | AT [cmds] &V [cmds] | |--------------+---------------------------------------------| | Description: | Displays active and stored configuration | | | profiles | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | &V1 | Display connection statistics | +------------------------------------------------------------+ Extended AT Commands +------------------------------------------------------------+ | EXTENDED RESULT CODES | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] \Vn [cmds] | |--------------+---------------------------------------------| | Description: | Selects extended result codes | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | \V0 | Connect messages are controlled by settings | | | X, W, and S95 | |--------------+---------------------------------------------| | \V1 | Connect messages are displayed in the | | | single line format | +------------------------------------------------------------+ +------------------------------------------------------------+ | PLUG AND PLAY SERIAL NUMBER | |------------------------------------------------------------| | Type: | Immediate | |--------------+---------------------------------------------| | Format: | AT [cmds] %7 [cmds] | |--------------+---------------------------------------------| | Description: | Returns the plug & play serial number | +------------------------------------------------------------+ +------------------------------------------------------------+ | PLUG AND PLAY VENDOR ID | |------------------------------------------------------------| | Type: | Immediate | |--------------+---------------------------------------------| | Format: | AT [cmds] %8 [cmds] | |--------------+---------------------------------------------| | Description: | Returns the plug & play vendor ID and | | | product number | +------------------------------------------------------------+ +------------------------------------------------------------+ | RPI MODE SELECTION | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] +Hn [cmds] | |--------------+---------------------------------------------| | Description: | Sets the RPI mode | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | +H0 | RPI/video ready mode disabled | |--------------+---------------------------------------------| | +H1 | RPI enabled and set DTE speed to 19200bps | |--------------+---------------------------------------------| | +H2 | RPI enabled and set DTE speed to 38400bps | |--------------+---------------------------------------------| | +H3 | RPI enabled and set DTE speed to 57600bps | |--------------+---------------------------------------------| | +H11 | RPI+ mode enabled | |--------------+---------------------------------------------| | +H16 | Video ready mode enabled | +------------------------------------------------------------+ +------------------------------------------------------------+ | DISTINCTIVE RING | |------------------------------------------------------------| | Type: | Immediate | |--------------+---------------------------------------------| | Format: | AT [cmds] -SDR=n [cmds] | |--------------+---------------------------------------------| | Description: | Selects the distinctive ring settings | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | -SDR=0 | Distinctive ring disabled | |--------------+---------------------------------------------| | -SDR=1 | Type 1 enabled | |--------------+---------------------------------------------| | -SDR=2 | Type 2 enabled | |--------------+---------------------------------------------| | -SDR=3 | Type 1 and 2 enabled | |--------------+---------------------------------------------| | -SDR=4 | Type 3 enabled | |--------------+---------------------------------------------| | -SDR=5 | Type 1 and 3 enabled | |--------------+---------------------------------------------| | -SDR=6 | Type 2 and 3 enabled | |--------------+---------------------------------------------| | -SDR=7 | Type 1, 2, and 3 enabled | +------------------------------------------------------------+ +------------------------------------------------------------+ | MNP10-EC | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] -SECn [cmds] | |--------------+---------------------------------------------| | Description: | Controls MNP10-EC | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | -SEC0 | MNP10-EC disabled | |--------------+---------------------------------------------| | -SEC1 | MNP10-EC enabled ans set transmit (TX) | | | level to 0 - 30 | +------------------------------------------------------------+ S(status) -REGISTERS +------------------------------------------------------------+ | AUTOSYNC OPTIONS | |------------------------------------------------------------| | Type: | Register | |--------------+---------------------------------------------| | Format | AT [cmds] S19=n [cmds] | |--------------+---------------------------------------------| | Default: | 0 | |--------------+---------------------------------------------| | Range: | Unidentified | |--------------+---------------------------------------------| | Description: | Sets the AutoSync option | +------------------------------------------------------------+ +------------------------------------------------------------+ | AUTOSYNC HDLC ADDRESS | |------------------------------------------------------------| | Type: | Register | |--------------+---------------------------------------------| | Format | AT [cmds] S20=n [cmds] | |--------------+---------------------------------------------| | Default: | 0 | |--------------+---------------------------------------------| | Range: | 0-255 | |--------------+---------------------------------------------| | Description: | Sets the AutoSync HDLC address of BSC Sync | | | charactyer | +------------------------------------------------------------+