ACER, INC. ========== MAGIC F34 Card Type Modem/Fax card Chip Set Unidentified Maximum Modem Rate 33.6Kbps Maximum Fax Rate 14.4Kbps Data Modulation Bell 103/212A Protocol ITU-T V.22, V.22bis, V.23, V.32, V.32bis, V.34 Fax Modulation ITU-T V.17, V.33, V.29, V.27ter, Protocol V.21CH2 Error MNP5, V.42, V.42bis Correction/Compression Fax Class Class I & II Data Bus 16-bit ISA Card Size Half length, full-height card +------------------------------------------------------------+ | CONNECTIONS | |------------------------------------------------------------| | Function | Label | Function | Label | |------------------------------------------------------------| | Telephone line out | CN1 | Microphone | CN4 | |---------------------+---------+----------------------+-----| | Telephone line in | CN2 | Audio card connector | CN5 | |---------------------+---------+----------------------+-----| | Line out | CN3 | | | +------------------------------------------------------------+ +------------------------------------------------------------+ | SERIAL PORT ADDRESS | |------------------------------------------------------------| | Setting | JP2 | JP3 | JP4 | JP5 | |---------------+---------+---------------+---------+--------| | COM1 | 1 & 2 | 2 & 3 | 2 & 3 | 2 & 3 | |---------------+---------+---------------+---------+--------| | COM2 | 2 & 3 | 1 & 2 | 2 & 3 | 1 & 2 | |---------------+---------+---------------+---------+--------| | i Plug and | 1 & 2 | Unidentified | 1 & 2 | 1 & 2 | | Play enabled | | | | | |------------------------------------------------------------| | Note: Pins designated should be in the closed position. To | | use the plug and play option, the optional chip C1 must be | | installed. | +------------------------------------------------------------+ +------------------------------------------------------------+ | SUPPORTED COMMAND SET | |------------------------------------------------------------| | Basic AT Commands | |------------------------------------------------------------| | AT, '+++', A/ | |------------------------------------------------------------| | A, B, C, E, H, M, O, P, Q, T, V, W, X, Y, Z | |------------------------------------------------------------| | &C, &F, &M, &P, &Q, &T, &V, &W, &Y, &Z | |------------------------------------------------------------| | Extended AT Commands | |------------------------------------------------------------| | \A, \B, \K, \N, \V, | |------------------------------------------------------------| | %C, %E, %L, %Q, %TT | |------------------------------------------------------------| | S Registers | |------------------------------------------------------------| | S0, S1, S2, S3, S4, S5, S6, S7, S8, S9, S10, S11, S12, | | S14, S16, S18, S19, S20, S21, S22, S23, | |------------------------------------------------------------| | S24, S25, S26, S29, S30, S31, S32, S33, S36, S37, S38, | | S39, S40, S41, S46, S48, S82, S86, S91, | |------------------------------------------------------------| | S92, S95 | |------------------------------------------------------------| | Special Commands | |------------------------------------------------------------| | #CID, +MS?, +MS, #BDR, #CLS, #MDL?, #MFR?, #REV?, #TL, | | #VBQ, #VBS, #VBT, #VCI?, #VLS, | |------------------------------------------------------------| | #VRA, #VRN, #VRX, #VSD, #VSK, #VSP, #VSR, #VSS, #VTD, | | #VTM, #VTS, #VTX | |------------------------------------------------------------| | Note: See MHI Help File for full command documentation. | +------------------------------------------------------------+ Proprietary AT Command Set +------------------------------------------------------------+ | AUTO-MODE DETECTION | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] Nn [cmds] | |--------------+---------------------------------------------| | Description: | Selects various options for the automatic | | | detection and negotiation of protocols | | | during the handshake process if the modem | | | is communicating with a remote modem of | | | dissimilar speed. | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | N0 | Auto-mode detection disabled | |--------------+---------------------------------------------| | N1 | Auto-mode detection enabled | +------------------------------------------------------------+ +------------------------------------------------------------+ | BLACKLISTED NUMBERS | |------------------------------------------------------------| | Type: | Immediate | |--------------+---------------------------------------------| | Format: | AT [cmds] *B [cmds] | |--------------+---------------------------------------------| | Description: | Sends the list of 'blacklisted' numbers to | | | the DTE. If no numbers are blacklisted, the | | | OK result code is sent | +------------------------------------------------------------+ +------------------------------------------------------------+ | DATA SET READY (DSR) | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] &Sn [cmds] | |--------------+---------------------------------------------| | Description: | Selects DSR options | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | &S0 | DSR forced high | |--------------+---------------------------------------------| | &S1 | DSR high only while modem is handshaking or | | | connected | +------------------------------------------------------------+ +------------------------------------------------------------+ | DATA TERMINAL READY (DTR) | |------------------------------------------------------------| | Type: | Configuration | |---------------+--------------------------------------------| | Format: | AT [cmds] &Dn [cmds] | |---------------+--------------------------------------------| | Description: | Selects modem response to DTR | |------------------------------------------------------------| | Note: The action each variant of &D causes depends on | | the setting of &Q | |------------------------------------------------------------| | &Q Setting | &D0 | &D1 | &D2 | &D3 | |------------------+----------+----------+---------+---------| | &Q0, &Q5, &Q6 | Command | Command | Command | Command | | | 0 | 1 | 2 | 3 | |------------------+----------+----------+---------+---------| | &Q1, &Q4 | Command | Command | Command | Command | | | 4 | 1 | 2 | 3 | |------------------+----------+----------+---------+---------| | &Q2, &Q3 | Command | Command | Command | Command | | | 2 | 2 | 2 | 2 | |------------------------------------------------------------| | Command | Function | |---------------+--------------------------------------------| | Command 0 | Modem does not respond to DTR | |---------------+--------------------------------------------| | Command 1 | Modem goes to command mode after DTR goes | | | off | |---------------+--------------------------------------------| | Command 2 | Modem goes to command mode and disconnects | | | (hangs up) after DTR goes off; Auto-Answer | | | is disabled. | |---------------+--------------------------------------------| | Command 3 | Modem is initialized after DTR goes off | |---------------+--------------------------------------------| | Command 4 | Modem goes to command mode and disconnects | | | (hangs up) after DTR goes off. | +------------------------------------------------------------+ +------------------------------------------------------------+ | DIAL | |------------------------------------------------------------| | Type: | Immediate | |--------------+---------------------------------------------| | Format: | AT [cmds] D<#> [cmds] | |--------------+---------------------------------------------| | Description: | Dials telephone number according to any | | | modifiers included in the string | |--------------+---------------------------------------------| | Note: | Any combination of modifiers can be used to | | | produce the desired dial functions in | | | sequence. | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | 0-9 | Dialing digits | |--------------+---------------------------------------------| | A, B, C, D, | Tone dial characters | | *, # | | |--------------+---------------------------------------------| | P | Pulse dial | |--------------+---------------------------------------------| | R | Reverse originate mode | |--------------+---------------------------------------------| | S=n | Dial NVRAM telephone number | |--------------+---------------------------------------------| | T | Tone dial | |--------------+---------------------------------------------| | W | Wait for dial tone | |--------------+---------------------------------------------| | , | Pause | |--------------+---------------------------------------------| | ! | Flash hook, modem goes on hook for .75 | | | seconds | |--------------+---------------------------------------------| | @ | Wait for quiet answer | |--------------+---------------------------------------------| | ^ | Disable data calling tone for a single call | | | origination | |--------------+---------------------------------------------| | ; | Modem returned to idle state after dialing. | | | The semicolon can only be placed at the end | | | of the dial command | |--------------+---------------------------------------------| | -( ) space | Ignored by modem. The modem ignores these | | | characters, but they can be included in the | | | dial string for separation purposes | +------------------------------------------------------------+ +------------------------------------------------------------+ | FLOW CONTROL | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] &Kn [cmds] | |--------------+---------------------------------------------| | Description: | Enables flow control options | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | &K0 | Flow control disabled | |--------------+---------------------------------------------| | &K3 | RTS/CTS flow control enabled | |--------------+---------------------------------------------| | &K4 | XON/XOFF flow control enabled | |--------------+---------------------------------------------| | &K5 | Transparent XON/XOFF flow control enabled | |--------------+---------------------------------------------| | &K6 | Unidirectional XON/XOFF flow control | | | enabled | +------------------------------------------------------------+ +------------------------------------------------------------+ | GUARD TONE | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] &Gn [cmds] | |--------------+---------------------------------------------| | Description: | Commands the modem to transmit a guard tone | | | in V.22/V.22bis | |------------------------------------------------------------| | Note: Used primarily for international data | | transmission | |------------------------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | &G0 | Guard tone disabled | |--------------+---------------------------------------------| | &G1 | Guard tone disabled | |--------------+---------------------------------------------| | &G2 | 1800Hz guard tone enabled | +------------------------------------------------------------+ +------------------------------------------------------------+ | REPORT INFORMATION | |------------------------------------------------------------| | Type: | Immediate | |--------------+---------------------------------------------| | Format: | AT [cmds] In [cmds] | |--------------+---------------------------------------------| | Description: | Displays information requested | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | I0 | Reports product code | |--------------+---------------------------------------------| | I1 | Calculates and verifies the ROM checksum | |--------------+---------------------------------------------| | I2 | Calculates and compares the ROM checksum | | | with the pre-stored checksum | |--------------+---------------------------------------------| | I3 | Reports the firmware version, basic model, | | | application code, and interface type code | |--------------+---------------------------------------------| | I4 | Reports OEM defined identifier string in | | | either Hayes-compatible binary format or | | | ASCII format | |--------------+---------------------------------------------| | I5 | Reports country code | |--------------+---------------------------------------------| | I6 | Reports modem data pump model and internal | | | code revision | +------------------------------------------------------------+ +------------------------------------------------------------+ | SPEAKER VOLUME | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] Ln [cmds] | |--------------+---------------------------------------------| | Description: | Controls speaker volume | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | L0 | Low speaker volume | |--------------+---------------------------------------------| | L1 | Low volume setting | |--------------+---------------------------------------------| | L2 | Medium volume setting | |--------------+---------------------------------------------| | L3 | Highest volume setting | +------------------------------------------------------------+