ACER, INC. ========== MAGIC MP32 Card Type Modem, Fax, Sound card Chip Set Unidentified I/O Options CD-ROM interface, microphone, audio line in, audio line out, wavetable interface Maximum Modem Rate 33.6Kbps Maximum Fax Rate 14.4Kbps Data Modulation Bell 103/212A Protocol ITU-T V.22, V.22bis, V.23, V.32, V.32bis, V.34, V.34bis Fax Modulation ITU-T V.17, V.21CH2, V.27ter, V.29, Protocol V.33 Error MNP5, V.42, V.42bis Correction/Compression Fax Class Class I & II Data Bus 16-bit ISA Card Size Full-length, full-height card +------------------------------------------------------------+ | CONNECTIONS | |------------------------------------------------------------| | Function | Label | Function | Label | |------------------------------------------------------------| | MIDI/Game port | CN1 | Wave table | CN6 | | | | interface | | |----------------------+---------+---------------------+-----| | Telephone line in | CN4 | Speaker/Line out | CN7 | |----------------------+---------+---------------------+-----| | Telephone line out | CN5 | Line in | CN8 | |----------------------+---------+---------------------+-----| | Microphone in | CN9 | CD-Audio | JP5 | +------------------------------------------------------------+ +------------------------------------------------------------+ | SPEAKER/LINE OUT SETTINGS | |------------------------------------------------------------| | Function | CN2 | CN3 | |----------------------------+---------------+---------------| | Speaker mode enabled (CN7) | Pins 1 & 2 | Pins 1 & 2 | | | closed | closed | |----------------------------+---------------+---------------| | Line out function enabled | Pins 2 & 3 | Pins 2 & 3 | | | closed | closed | +------------------------------------------------------------+ +------------------------------------------------------------+ | SUPPORTED COMMAND SET | |------------------------------------------------------------| | Basic AT Commands | |------------------------------------------------------------| | AT, A/ | |------------------------------------------------------------| | A, B, C, D, E, H, M, O, P, Q, T, V, W, X, Y, Z | |------------------------------------------------------------| | &C, &F, &P, &Q, &R, &V, &W, &Y, &Z | |------------------------------------------------------------| | Extended AT Commands | |------------------------------------------------------------| | \A, \B, \K, \N, \V, | |------------------------------------------------------------| | %C, %E, %L, %Q, %TT | |------------------------------------------------------------| | S Registers | |------------------------------------------------------------| | S0, S1, S2, S3, S4, S5, S6, S7, S8, S9, S10, S11, S12, | | S14, S16, S18, S21, S22, S23, S24, S25, | |------------------------------------------------------------| | S26, S27, S28, S29, S30, S31, S32, S33, S36, S37, S38, | | S39, S40, S41, S46, S48, S82, S86, S91, | |------------------------------------------------------------| | S92, S95 | |------------------------------------------------------------| | Special Commands | |------------------------------------------------------------| | #CID, +MS, #BDR, #CLS, MDL?, #MFR?, #REV?, #TL, #VBQ?, | | #VBS, #VBT, #VCI?, #VLS, #VRA, #VRN, | |------------------------------------------------------------| | #VRX, #VSD, #VSK, #VSP, #VSR, #VSS, #VTD, #VTM, #VTS, #VTX | |------------------------------------------------------------| | Note: See MHI Help File for full command documentation. | +------------------------------------------------------------+ Proprietary AT Command Set +------------------------------------------------------------+ | AUTO-MODE DETECTION | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] Nn [cmds] | |--------------+---------------------------------------------| | Description: | Selects various options for the automatic | | | detection and negotiation of protocols | | | during the handshake process if the modem | | | is communicating with a remote modem of | | | dissimilar speed. | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | N0 | Auto-mode detection disabled | |--------------+---------------------------------------------| | N1 | Auto-mode detection enabled | +------------------------------------------------------------+ +------------------------------------------------------------+ | CLOCK SOURCE - SYNCHRONOUS TRANSMIT | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] &Xn [cmds] | |--------------+---------------------------------------------| | Description: | Selects DTE transmit clock source | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | &X0 | Modem generates clock | |--------------+---------------------------------------------| | &X1 | Modem generates clock from the receive | | | carrier signal | +------------------------------------------------------------+ +------------------------------------------------------------+ | COMMUNICATIONS MODE | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] &Mn [cmds] | |--------------+---------------------------------------------| | Description: | Selects communications mode | |--------------+---------------------------------------------| | Command | Mode | |--------------+---------------------------------------------| | &M0 | Asynchronous mode | |--------------+---------------------------------------------| | &M1 | Synchronous connect mode and asynchronous | | | off-line command mode. | |--------------+---------------------------------------------| | &M2 | Synchronous connect mode and asynchronous | | | off-line command mode and set DTR high. | |--------------+---------------------------------------------| | &M3 | Synchronous connect mode and asynchronous | | | off-line command mode and set DTR to low. | +------------------------------------------------------------+ +------------------------------------------------------------+ | DATA SET READY (DSR) | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] &Sn [cmds] | |--------------+---------------------------------------------| | Description: | Selects DSR options | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | &S0 | DSR forced high | |--------------+---------------------------------------------| | &S1 | DSR high only while modem is handshaking or | | | connected | +------------------------------------------------------------+ +------------------------------------------------------------+ | DATA TERMINAL READY (DTR) | |------------------------------------------------------------| | Type: | Configuration | |---------------+--------------------------------------------| | Format: | AT [cmds] &Dn [cmds] | |---------------+--------------------------------------------| | Description: | Selects modem response to DTR | |------------------------------------------------------------| | Note: The action each variant of &D causes depends on | | the setting of &Q | |------------------------------------------------------------| | &Q Setting | &D0 | &D1 | &D2 | &D3 | |------------------+---------+---------+---------+-----------| | &Q0, &Q5, &Q6 | Command | Command | Command | Command 3 | | | 0 | 1 | 2 | | |------------------+---------+---------+---------+-----------| | &Q1, &Q4 | Command | Command | Command | Command 3 | | | 2 | 1 | 2 | | |------------------+---------+---------+---------+-----------| | &Q2, &Q3 | Command | Command | Command | Command 2 | | | 2 | 2 | 2 | | |------------------------------------------------------------| | Command | Function | |---------------+--------------------------------------------| | Command 0 | Modem does not respond to DTR | |---------------+--------------------------------------------| | Command 1 | Modem goes to command mode after DTR goes | | | is off | |---------------+--------------------------------------------| | Command 2 | Modem goes to command mode and disconnects | | | (hangs up) after DTR goes off. | |---------------+--------------------------------------------| | Command 3 | Modem is initialized after DTR goes off | +------------------------------------------------------------+ +------------------------------------------------------------+ | FLOW CONTROL | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] &Kn [cmds] | |--------------+---------------------------------------------| | Description: | Enables flow control options | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | &K0 | Flow control disabled | |--------------+---------------------------------------------| | &K3 | RTS/CTS and DTE/DCE flow control enabled | |--------------+---------------------------------------------| | &K4 | XON/XOFF and DTE/DCE flow control enabled | |--------------+---------------------------------------------| | &K5 | Transparent XON/XOFF flow control enabled | |--------------+---------------------------------------------| | &K6 | RTS/CTS and XON/XOFF flow control enabled | +------------------------------------------------------------+ +------------------------------------------------------------+ | GUARD TONE | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] &Gn [cmds] | |--------------+---------------------------------------------| | Description: | Commands the modem to transmit a guard tone | | | in V.22/V.22bis | |------------------------------------------------------------| | Note: Used primarily for international data | | transmission | |------------------------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | &G0 | Guard tone disabled | |--------------+---------------------------------------------| | &G1 | Guard tone disabled | |--------------+---------------------------------------------| | &G2 | 1800Hz guard tone enabled | +------------------------------------------------------------+ +------------------------------------------------------------+ | REPORT INFORMATION | |------------------------------------------------------------| | Type: | Immediate | |--------------+---------------------------------------------| | Format: | AT [cmds] In [cmds] | |--------------+---------------------------------------------| | Description: | Displays information requested | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | I0 | Reports modem model and speed | |--------------+---------------------------------------------| | I1 | Reports ROM checksum | |--------------+---------------------------------------------| | I2 | Reports OK | |--------------+---------------------------------------------| | I3 | Reports firmware revision, model and | | | interface type | |--------------+---------------------------------------------| | I4 | Reports response programmed by OEM | |--------------+---------------------------------------------| | I5 | Reports the country code parameter | |--------------+---------------------------------------------| | I6 | Reports modem data pump model and code | | | revision | +------------------------------------------------------------+ +------------------------------------------------------------+ | SPEAKER VOLUME | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] Ln [cmds] | |--------------+---------------------------------------------| | Description: | Controls speaker volume | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | L0 | Low volume setting | |--------------+---------------------------------------------| | L1 | Low volume setting | |--------------+---------------------------------------------| | L2 | Medium volume setting | |--------------+---------------------------------------------| | L3 | Highest volume setting | +------------------------------------------------------------+ +------------------------------------------------------------+ | TEST MODES | |------------------------------------------------------------| | Type: | Immediate | |--------------+---------------------------------------------| | Format: | AT [cmds] &Tn | |--------------+---------------------------------------------| | Description: | Selects test options | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | &T0 | End current test | |--------------+---------------------------------------------| | &T1 | Begin local analog loopback test | |--------------+---------------------------------------------| | &T2 | Returns error result code | |--------------+---------------------------------------------| | &T3 | Begin local digital loopback | |--------------+---------------------------------------------| | &T4 | Grant remote digital loopback request | |--------------+---------------------------------------------| | &T5 | Deny remote digital loopback request | |--------------+---------------------------------------------| | &T6 | Request remote digital loopback | |--------------+---------------------------------------------| | &T7 | Request remote digital loopback and | | | self-test | |--------------+---------------------------------------------| | &T8 | Begin local analog loopback and self-test | +------------------------------------------------------------+ S(status) -REGISTERS +------------------------------------------------------------+ | AUTOSYNC OPTIONS | |------------------------------------------------------------| | Type: | Register | |--------------+---------------------------------------------| | Format | AT [cmds] S19=n | |--------------+---------------------------------------------| | Default: | 0 | |--------------+---------------------------------------------| | Description: | Enables selection of the autosync options | +------------------------------------------------------------+ +------------------------------------------------------------+ | AUTOSYNC OR BSC SYNC ENABLED | |------------------------------------------------------------| | Type: | Register | |--------------+---------------------------------------------| | Format | AT [cmds] S20=n | |--------------+---------------------------------------------| | Default: | 0 | |--------------+---------------------------------------------| | Description: | Enables autosync HDLC address or BSC sync | | | characters | +------------------------------------------------------------+