ACTIONTEC ELECTRONICS, INC. =========================== 56K X2 DATA/FAX Card Type Modem (asynchronous) Chipset Unidentified Maximum Data Rate 56Kbps Maximum Fax Rate 14.4Kbps Data Modulation Bell 103A, 212A ITU-T V.21, V.22, V.22bis, V.23, V.32, V.32bis, V.34 U.S. Robotics x2 Fax Modulation ITU-T V.17, V.21CH2, V.27ter, V.29 Error MNP5, V.42, V.42bis Correction/Compression Fax Class Class I Data Bus 8-bit ISA Card Size Full height, half length +------------------------------------------------------------+ | CONNECTIONS | |------------------------------------------------------------| | Function | Label | Function | Label | |----------------------+-------+---------------------+-------| | Telephone line out | CN1 | Telephone line in | CN2 | +------------------------------------------------------------+ +------------------------------------------------------------+ | USER CONFIGURABLE SETTINGS | |------------------------------------------------------------| | Setting | Label | Position | |----------------------------------------+-------+-----------| | i Plug-N-Play enabled | J3/C | Open | |----------------------------------------+-------+-----------| | Plug-N-Play disabled | J3/C | Closed | +------------------------------------------------------------+ +------------------------------------------------------------+ | SERIAL PORT ADDRESS SELECTION | |------------------------------------------------------------| | Setting | J3/A | J3/B | |--------------------+-------------------+-------------------| | 3F8h (COM1:) | Closed | Closed | |--------------------+-------------------+-------------------| | 2E8h (COM2:) | Open | Closed | |--------------------+-------------------+-------------------| | 3F8h (COM3:) | Closed | Open | |--------------------+-------------------+-------------------| | 2E8h (COM4:) | Open | Open | |--------------------+-------------------+-------------------| | i Plug-N-Play | Open | Open | +------------------------------------------------------------+ +------------------------------------------------------------+ | INTERRUPT SELECTION | |------------------------------------------------------------| | Setting | J2/A | J2/B | J2/C | J2/D | J2/E | |---------------+--------+--------+--------+--------+--------| | 2 | Closed | Open | Open | Open | Open | |---------------+--------+--------+--------+--------+--------| | 3 | Open | Closed | Open | Open | Open | |---------------+--------+--------+--------+--------+--------| | 4 | Open | Open | Closed | Open | Open | |---------------+--------+--------+--------+--------+--------| | 5 | Open | Open | Open | Closed | Open | |---------------+--------+--------+--------+--------+--------| | 7 | Open | Open | Open | Open | Closed | |---------------+--------+--------+--------+--------+--------| | i Plug-N-Play | Open | Open | Open | Open | Open | +------------------------------------------------------------+ +--------------------------------------------------------+ | SUPPORTED STANDARD COMMANDS | |--------------------------------------------------------| | Basic AT Commands | |--------------------------------------------------------| | +++, 'comma', A/ | |--------------------------------------------------------| | A, B, D, E, F, H, L, M, O, Q, V, X, Y, Z | |--------------------------------------------------------| | &C, &D, &F, &G, &P, &R, &S, &T, &W, &Z | |--------------------------------------------------------| | S-Registers | |--------------------------------------------------------| | The S-registers are unidentified. | |--------------------------------------------------------| | Note: See MHI help file for complete information. | +--------------------------------------------------------+ +------------------------------------------------------------+ | BREAK TYPE | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] &Yn [cmds] | |--------------+---------------------------------------------| | Description: | Configures action of break signal. | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | &Y0 | Break empties buffer. | |--------------+---------------------------------------------| | i &Y1 | Break empties buffer and is sent | | | immediately. | |--------------+---------------------------------------------| | &Y2 | Break does not empty buffer and is sent | | | immediately. | +------------------------------------------------------------+ +------------------------------------------------------------+ | COMPRESSION MODE | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] &Kn [cmds] | |--------------+---------------------------------------------| | Description: | Selects the type of data compression that | | | will be used. | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | &K0 | Data compression disabled. | |--------------+---------------------------------------------| | i &K1 | Auto-detect compression mode. | |--------------+---------------------------------------------| | &K2 | Data compression enabled. | |--------------+---------------------------------------------| | &K3 | MNP5 data compression only enabled. | +------------------------------------------------------------+ +------------------------------------------------------------+ | CONNECTION SPEED LOWER LIMIT | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] &Un [cmds] | |--------------+---------------------------------------------| | Description: | Sets slowest allowed connection speed if &N | | | is set to 1 or higher. | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | i &U0 | No minimum connect speed. | |--------------+---------------------------------------------| | &U1 | Set minimum connect speed to 300bps. | |--------------+---------------------------------------------| | &U2 | Set minimum connect speed to 1200bps. | |--------------+---------------------------------------------| | &U3 | Set minimum connect speed to 2400bps. | |--------------+---------------------------------------------| | &U4 | Set minimum connect speed to 4800bps. | |--------------+---------------------------------------------| | &U5 | Set minimum connect speed to 7200bps. | |--------------+---------------------------------------------| | &U6 | Set minimum connect speed to 9600bps. | |--------------+---------------------------------------------| | &U7 | Set minimum connect speed to 12Kbps. | |--------------+---------------------------------------------| | &U8 | Set minimum connect speed to 14.4Kbps. | |--------------+---------------------------------------------| | &U9 | Set minimum connect speed to 16.8Kbps. | |--------------+---------------------------------------------| | &U10 | Set minimum connect speed to 19.2Kbps. | |--------------+---------------------------------------------| | &U11 | Set minimum connect speed to 21.6Kbps. | |--------------+---------------------------------------------| | &U12 | Set minimum connect speed to 24Kbps. | |--------------+---------------------------------------------| | &U13 | Set minimum connect speed to 26.4Kbps. | |--------------+---------------------------------------------| | &U14 | Set minimum connect speed to 28.8Kbps. | |--------------+---------------------------------------------| | &U15 | Set minimum connect speed to 31.2Kbps. | |--------------+---------------------------------------------| | &U16 | Set minimum connect speed to 33.6Kbps. | |--------------+---------------------------------------------| | &U17 | Set minimum connect speed to 33.3Kbps. | |--------------+---------------------------------------------| | &U18 | Set minimum connect speed to 37.3Kbps. | |--------------+---------------------------------------------| | &U19 | Set minimum connect speed to 41.3Kbps. | |--------------+---------------------------------------------| | &U20 | Set minimum connect speed to 42.6Kbps. | |--------------+---------------------------------------------| | &U21 | Set minimum connect speed to 44Kbps. | |--------------+---------------------------------------------| | &U22 | Set minimum connect speed to 45.3Kbps. | |--------------+---------------------------------------------| | &U23 | Set minimum connect speed to 46.6Kbps. | |--------------+---------------------------------------------| | &U24 | Set minimum connect speed to 48Kbps. | |--------------+---------------------------------------------| | &U25 | Set minimum connect speed to 49.3Kbps. | |--------------+---------------------------------------------| | &U26 | Set minimum connect speed to 50.6Kbps. | |--------------+---------------------------------------------| | &U27 | Set minimum connect speed to 52Kbps. | |--------------+---------------------------------------------| | &U28 | Set minimum connect speed to 53.3Kbps. | |--------------+---------------------------------------------| | &U29 | Set minimum connect speed to 54.6Kbps. | |--------------+---------------------------------------------| | &U30 | Set minimum connect speed to 56Kbps. | |--------------+---------------------------------------------| | &U31 | Set minimum connect speed to 57.3Kbps. | +------------------------------------------------------------+ +------------------------------------------------------------+ | CONNECTION SPEED UPPER LIMIT | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] &Nn [cmds] | |--------------+---------------------------------------------| | Description: | Sets required connection speed if &U is set | | | to 0; otherwise, sets fastest allowed | | | connection speed. | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | i &N0 | No maximum connect speed. | |--------------+---------------------------------------------| | &N1 | Set maximum connect speed to 300bps. | |--------------+---------------------------------------------| | &N2 | Set maximum connect speed to 1200bps. | |--------------+---------------------------------------------| | &N3 | Set maximum connect speed to 2400bps. | |--------------+---------------------------------------------| | &N4 | Set maximum connect speed to 4800bps. | |--------------+---------------------------------------------| | &N5 | Set maximum connect speed to 7200bps. | |--------------+---------------------------------------------| | &N6 | Set maximum connect speed to 9600bps. | |--------------+---------------------------------------------| | &N7 | Set maximum connect speed to 12Kbps. | |--------------+---------------------------------------------| | &N8 | Set maximum connect speed to 14.4Kbps. | |--------------+---------------------------------------------| | &N9 | Set maximum connect speed to 16.8Kbps. | |--------------+---------------------------------------------| | &N10 | Set maximum connect speed to 19.2Kbps. | |--------------+---------------------------------------------| | &N11 | Set maximum connect speed to 21.6Kbps. | |--------------+---------------------------------------------| | &N12 | Set maximum connect speed to 24Kbps. | |--------------+---------------------------------------------| | &N13 | Set maximum connect speed to 26.4Kbps. | |--------------+---------------------------------------------| | &N14 | Set maximum connect speed to 28.8Kbps. | |--------------+---------------------------------------------| | &N15 | Set maximum connect speed to 31.2Kbps. | |--------------+---------------------------------------------| | &N16 | Set maximum connect speed to 33.6Kbps. | |--------------+---------------------------------------------| | &N17 | Set maximum connect speed to 33.3Kbps. | |--------------+---------------------------------------------| | &N18 | Set maximum connect speed to 37.3Kbps. | |--------------+---------------------------------------------| | &N19 | Set maximum connect speed to 41.3Kbps. | |--------------+---------------------------------------------| | &N20 | Set maximum connect speed to 42.6Kbps. | |--------------+---------------------------------------------| | &N21 | Set maximum connect speed to 44Kbps. | |--------------+---------------------------------------------| | &N22 | Set maximum connect speed to 45.3Kbps. | |--------------+---------------------------------------------| | &N23 | Set maximum connect speed to 46.6Kbps. | |--------------+---------------------------------------------| | &N24 | Set maximum connect speed to 48Kbps. | |--------------+---------------------------------------------| | &N25 | Set maximum connect speed to 49.3Kbps. | |--------------+---------------------------------------------| | &N26 | Set maximum connect speed to 50.6Kbps. | |--------------+---------------------------------------------| | &N27 | Set maximum connect speed to 52Kbps. | |--------------+---------------------------------------------| | &N28 | Set maximum connect speed to 53.3Kbps. | |--------------+---------------------------------------------| | &N29 | Set maximum connect speed to 54.6Kbps. | |--------------+---------------------------------------------| | &N30 | Set maximum connect speed to 56Kbps. | |--------------+---------------------------------------------| | &N31 | Set maximum connect speed to 57.3Kbps. | +------------------------------------------------------------+ +------------------------------------------------------------+ | DISPLAY INFORMATION | |------------------------------------------------------------| | Type: | Immediate | |--------------+---------------------------------------------| | Format: | AT [cmds] In [cmds] | |--------------+---------------------------------------------| | Description: | Displays modem properties. | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | I0 | Displays product identification code. | |--------------+---------------------------------------------| | I1 | Tests and displays ROM checksum result. | |--------------+---------------------------------------------| | I2 | Tests and displays RAM checksum result. | |--------------+---------------------------------------------| | I3 | Displays product identification. | |--------------+---------------------------------------------| | I4 | Displays current command settings. | |--------------+---------------------------------------------| | I5 | Displays current NVRAM settings. | |--------------+---------------------------------------------| | I6 | Displays current connection's statistics. | |--------------+---------------------------------------------| | I7 | Displays product configuration. | +------------------------------------------------------------+ +------------------------------------------------------------+ | ERROR CORRECTION MODE | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] &Mn [cmds] | |--------------+---------------------------------------------| | Description: | Selects active error correction protocols. | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | &M0 | Normal mode only. | |--------------+---------------------------------------------| | i &M4 | Auto-detect mode. | |--------------+---------------------------------------------| | &M5 | Error correction mode only. | +------------------------------------------------------------+ +------------------------------------------------------------+ | EXTENDED RESULT CODES | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] &An [cmds] | |--------------+---------------------------------------------| | Description: | Selects extended result codes. | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | &A0 | Extended result codes disabled. | |--------------+---------------------------------------------| | &A1 | Error correction result codes enabled. | |--------------+---------------------------------------------| | &A2 | V.32 result code enabled. | |--------------+---------------------------------------------| | i &A3 | Error correction and compression result | | | codes enabled. | +------------------------------------------------------------+ +------------------------------------------------------------+ | FLOW CONTROL - MODEM-TO-MODEM | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] &In [cmds] | |--------------+---------------------------------------------| | Description: | Selects the type of modem-to-modem flow | | | control used. | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | i &I0 | Software flow control disabled. | |--------------+---------------------------------------------| | &I1 | XON/XOFF pass-through enabled. | |--------------+---------------------------------------------| | &I2 | XON/XOFF pass-through disabled. | +------------------------------------------------------------+ +------------------------------------------------------------+ | FLOW CONTROL TYPE | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] &Hn [cmds] | |--------------+---------------------------------------------| | Description: | Sets type of flow control used by modem. | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | &H0 | Flow control disabled. | |--------------+---------------------------------------------| | i &H1 | CTS/RTS flow control enabled. | |--------------+---------------------------------------------| | &H2 | XON/XOFF flow control enabled. | |--------------+---------------------------------------------| | &H3 | CTS/RTS and XON/XOFF flow control enabled. | +------------------------------------------------------------+ +------------------------------------------------------------+ | LOCK SERIAL PORT | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] &Bn [cmds] | |--------------+---------------------------------------------| | Description: | Sets operation of serial port speed. | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | &B0 | Serial speed follows connect speed. | |--------------+---------------------------------------------| | i &B1 | Serial speed locked. | |--------------+---------------------------------------------| | &B2 | Serial speed locked in error correction | | | mode only. | +------------------------------------------------------------+