ANGIA COMMUNICATIONS, INC. ========================== HIGH SPEED V.32BIS Card Type Modem (asynchronous) Chipset Unidentified Maximum Data Rate 14.4Kbps Maximum Fax Rate 14.4Kbps Data Modulation Bell 103A/212A ITU-T V.21, V.22, V.22bis, V.23, V.32, V.32bis Fax Modulation ITU-T V.17, V.21CH2, V.27ter, V.29 Error MNP5, MNP10, V.42, V.42bis Correction/Compression Fax Class Class II Data Bus PCMCIA Type II 53159 +------------------------------------------------------------+ | SUPPORTED STANDARD COMMANDS | |------------------------------------------------------------| | Basic AT Commands | |------------------------------------------------------------| | +++, 'comma', A/ | |------------------------------------------------------------| | A, B, E, H, L, M, N, O, Q, V, W, X, Y, Z | |------------------------------------------------------------| | &C, &D, &F, &G, &J, &L, &P, &R, &S, &T, &W, &Y, &Z | |------------------------------------------------------------| | Extended AT Commands | |------------------------------------------------------------| | \A, \B, \C, \G, \J, \N, \V, \Y, \Z | |------------------------------------------------------------| | %A, %C, %L | |------------------------------------------------------------| | Special AT Commands | |------------------------------------------------------------| | *H, )M, @M | |------------------------------------------------------------| | S-Registers | |------------------------------------------------------------| | S0, S1, S2, S3, S4, S5, S6, S7, S8, S9, S10, S11, S12, | | S14, S16, S18, S21, S22, S23, S24, S25, S26 | |------------------------------------------------------------| | S27, S28, S36, S38 | |------------------------------------------------------------| | Note: See MHI help file for complete information. | +------------------------------------------------------------+ Proprietary AT Command Set +------------------------------------------------------------+ | AUTO-REDIAL | |------------------------------------------------------------| | Type: | Register | |--------------+---------------------------------------------| | Format: | AT [cmds] S41=n [cmds] | |--------------+---------------------------------------------| | Default: | 0 | |--------------+---------------------------------------------| | Range: | 0 - 10 | |--------------+---------------------------------------------| | Unit: | 1 retry | |--------------+---------------------------------------------| | Description: | Sets the number of times the modem will | | | automatically redial a call that failed to | | | connect. | +------------------------------------------------------------+ +------------------------------------------------------------+ | AUTO-RELIABLE FALLBACK CHARACTER | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] S46=n [cmds] | |--------------+---------------------------------------------| | Default: | 13 | |--------------+---------------------------------------------| | Range: | 0 - 127 | |--------------+---------------------------------------------| | Unit: | 1 ASCII character | |--------------+---------------------------------------------| | Description: | Sets the character used as the | | | auto-reliable fallback character. | +------------------------------------------------------------+ +------------------------------------------------------------+ | AUTO-RELIABLE FALLBACK CHARACTER ENABLE | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] &Nn [cmds] | |--------------+---------------------------------------------| | Description: | Enables or disables the auto-reliable | | | fallback character. | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | &N0 | Auto-reliable fallback character disabled. | |--------------+---------------------------------------------| | i &N1 | Auto-reliable fallback character enabled. | +------------------------------------------------------------+ +------------------------------------------------------------+ | AUTO-RELIABLE TIME BUFFER CONFIGURATION | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] &On [cmds] | |--------------+---------------------------------------------| | Description: | Controls the handling of incoming data | | | during the auto-reliable negotiation time | | | period. | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | &O0 | Data is discarded. | |--------------+---------------------------------------------| | i &O1 | Date is sent to DTE. | +------------------------------------------------------------+ +------------------------------------------------------------+ | AUTO-RETRAIN | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] &En [cmds] | |--------------+---------------------------------------------| | Description: | Controls auto-retrain mode. | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | &E0 | Auto-retrain disabled. | |--------------+---------------------------------------------| | i &E1 | Auto-retrain enabled. | +------------------------------------------------------------+ +------------------------------------------------------------+ | ANSWER/ORIGINATE DETECTION PATTERNS | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] &An [cmds] | |--------------+---------------------------------------------| | Description: | Selects whether the modem will use answer | | | and originate detection patterns in | | | originate mode. | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | &A0 | Answer and originate detection patterns | | | disabled in originate mode. | |--------------+---------------------------------------------| | i &A1 | Answer and originate detection patterns | | | enabled in originate mode. | +------------------------------------------------------------+ +------------------------------------------------------------+ | BIT-MAPPED REGISTER S39 | |------------------------------------------------------------| | Format: | AT [cmds] S39=n [cmds] | |----------------+-------------------------------------------| | Default: | 0 | |----------------+-------------------------------------------| | Range: | 0 - 187 | |----------------+-------------------------------------------| | Description: | Controls power-up profile, local serial | | | port speed, break type, and auto-retrain. | |------------------------------------------------------------| | Bit | Value | Function | |------------------------------------------------------------| | 1, 0 | i | Restore profile 0 on power-up. | | | 00 | | | | | Restore profile 1 on power-up. | | | 01 | | | | | Restore profile 2 on power-up. | | | 10 | | | | | Restore profile 3 on power-up. | | | 11 | | |-------------+----+-----------------------------------------| | 2 | 0 | Not used. | |------------------------------------------------------------| | 3 | i 0 | Local serial port speed set with S23. | | | | | | | 1 | Local serial port speed fixed at | | | | 115.2Kbps. | |------------------------------------------------------------| | 5, 4 | i | Break sent with transmitted data. | | | 00 | | | | | Break sent to remote modem immediately. | | | 01 | | | | | Break sent to remote modem and buffers | | | 10 | cleared. | |-------------+----+-----------------------------------------| | 6 | 0 | Not used. | |-------------+----+-----------------------------------------| | 7 | i | Auto-retrain enabled. | | | 0 | | | | | Auto-retrain disabled. | | | 1 | | +------------------------------------------------------------+ +------------------------------------------------------------+ | BIT-MAPPED REGISTER S49 | |------------------------------------------------------------| | Format: | AT [cmds] S49=n [cmds] | |----------------+-------------------------------------------| | Default: | Unidentified | |----------------+-------------------------------------------| | Range: | 0 - 148 | |----------------+-------------------------------------------| | Description: | Controls flow control type and the | | | compromise equalizer. | |------------------------------------------------------------| | Bit | Value | Function | |----------+-------+-----------------------------------------| | 4 - 0 | 00000 | Flow control disabled. | | | | | | | i | RTS/CTS flow control enabled. | | | 00011 | | | | | XON/XOFF flow control enabled. | | | 00100 | | | | | Unidirectional transparent XON/XOFF | | | 01000 | flow control enabled. | | | | | | | 01100 | Local transparent XON/XOFF flow control | | | | enabled. | | | 10000 | | | | | Internal XON/XOFF flow control enabled. | | | 10100 | | | | | Internal local XON/XOFF flow control | | | | enabled. | |------------------------------------------------------------| | 6, 5 | 00 | Not used. | |-------------+------+---------------------------------------| | 7 | 0 | Compromise equalizer enabled. | | | | | | | 1 | Compromise equalizer disabled. | +------------------------------------------------------------+ +------------------------------------------------------------+ | BREAK TYPE | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] &In [cmds] | |--------------+---------------------------------------------| | Description: | Configures action of break signal. | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | &I0 | Break sent with transmitted data. | |--------------+---------------------------------------------| | &I1 | Break sent to remote modem immediately. | |--------------+---------------------------------------------| | &I2 | Break sent to remote modem and buffers | | | cleared. | +------------------------------------------------------------+ +------------------------------------------------------------+ | BREAK TYPE | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] \Kn [cmds] | |--------------+---------------------------------------------| | Description: | Configures action of break signal. | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | \K1 | Break sent to remote modem and buffers | | | cleared. | |--------------+---------------------------------------------| | \K3 | Break sent to remote modem immediately. | |--------------+---------------------------------------------| | \K5 | Break sent with transmitted data. | +------------------------------------------------------------+ +------------------------------------------------------------+ | COMMUNICATIONS MODE | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] &Qn [cmds] | |--------------+---------------------------------------------| | Description: | Selects the communications mode the modem | | | will use. | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | &Q0 | Modem will operate in asynchronous mode. | |--------------+---------------------------------------------| | &Q4 | Modem will operate in direct mode. | |--------------+---------------------------------------------| | &Q5 | Modem will use MNP reliable in asynchronous | | | mode. | |--------------+---------------------------------------------| | i &Q6 | Modem will use V.42 auto-reliable | | | asynchronous mode. | |--------------+---------------------------------------------| | &Q7 | Modem will use V.42 reliable asynchronous | | | mode. | +------------------------------------------------------------+ +------------------------------------------------------------+ | COMPRESSION | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] &Un [cmds] | |--------------+---------------------------------------------| | Description: | Selects whether the modem will use data | | | compression. | |------------------------------------------------------------| | Command | Function | |---------------------+--------------------------------------| | &U0 | Data compression disabled. | |---------------------+--------------------------------------| | i &U1 | Data compression enabled. | +------------------------------------------------------------+ +------------------------------------------------------------+ | COMPRESSION/ERROR CORRECTION TYPE | |------------------------------------------------------------| | Type: | Register | |--------------+---------------------------------------------| | Format: | AT [cmds] S44=n [cmds] | |--------------+---------------------------------------------| | Description: | Returns a value indicating the type of | | | error correction and compression in use for | | | the last connection. | |--------------+---------------------------------------------| | Value | Meaning | |--------------+---------------------------------------------| | 0 | Last connection used no error correction. | |--------------+---------------------------------------------| | 2 | Last connection used MNP2 error correction. | |--------------+---------------------------------------------| | 3 | Last connection used MNP3 error correction. | |--------------+---------------------------------------------| | 4 | Last connection used MNP4 error correction. | |--------------+---------------------------------------------| | 5 | Last connection used MNP5 compression. | |--------------+---------------------------------------------| | 6 | Last connection used V.42 error correction. | |--------------+---------------------------------------------| | 7 | Last connection used V.42bis compression. | +------------------------------------------------------------+ +------------------------------------------------------------+ | CONNECTION TYPE | |------------------------------------------------------------| | Type: | Register | |--------------+---------------------------------------------| | Format: | AT [cmds] S43? [cmds] | |--------------+---------------------------------------------| | Description: | Returns a value indicating the type and | | | speed of the last connection. | |--------------+---------------------------------------------| | Value | Meaning | |--------------+---------------------------------------------| | 0 | Last connection was at 300bps with no | | | error-correction. | |--------------+---------------------------------------------| | 1 | Last connection was at 1200bps with no | | | error-correction. | |--------------+---------------------------------------------| | 2 | Last connection was at 2400bps with no | | | error-correction. | |--------------+---------------------------------------------| | 3 | Last connection was at 1200bps in MNP mode. | |--------------+---------------------------------------------| | 4 | Last connection was at 2400bps in MNP mode. | |--------------+---------------------------------------------| | 5 | Last connection was at 1200bps in V.42 | | | mode. | |--------------+---------------------------------------------| | 6 | Last connection was at 2400bps in V.42 | | | mode. | |--------------+---------------------------------------------| | 7 | Last connection was at 4800bps with no | | | error-correction. | |--------------+---------------------------------------------| | 8 | Last connection was at 4800bps in MNP mode. | |--------------+---------------------------------------------| | 9 | Last connection was at 4800bps in V.42 | | | mode. | |--------------+---------------------------------------------| | 10 | Last connection was at 9600bps with no | | | error-correction. | |--------------+---------------------------------------------| | 11 | Last connection was at 9600bps in MNP mode. | |--------------+---------------------------------------------| | 12 | Last connection was at 9600bps in V.42 | | | mode. | |--------------+---------------------------------------------| | 13 | Last connection was at 300bps in MNP mode. | |--------------+---------------------------------------------| | 14 | Last connection was at 300bps in V.42 mode. | |--------------+---------------------------------------------| | 15 | Last connection was at 7200bps with no | | | error-correction. | |--------------+---------------------------------------------| | 16 | Last connection was at 7200bps in MNP mode. | |--------------+---------------------------------------------| | 17 | Last connection was at 7200bps in V.42 | | | mode. | |--------------+---------------------------------------------| | 18 | Last connection was at 12Kbps with no | | | error-correction. | |--------------+---------------------------------------------| | 19 | Last connection was at 12Kbps in MNP mode. | |--------------+---------------------------------------------| | 20 | Last connection was at 12Kbps in V.42 mode. | |--------------+---------------------------------------------| | 21 | Last connection was at 14.4Kbps with no | | | error-correction. | |--------------+---------------------------------------------| | 22 | Last connection was at 14.4Kbps in MNP | | | mode. | |--------------+---------------------------------------------| | 23 | Last connection was at 14.4Kbps in V.42 | | | mode. | +------------------------------------------------------------+ +------------------------------------------------------------+ | CONNECTION FAILURE CODES | |------------------------------------------------------------| | Type: | Register | |--------------+---------------------------------------------| | Format | AT [cmds] S45? [cmds] | |--------------+---------------------------------------------| | Description: | Returns a value which indicate the cause of | | | a connection failure. | |--------------+---------------------------------------------| | Value | Meaning | |--------------+---------------------------------------------| | 0 | Carrier signal lost. | |--------------+---------------------------------------------| | 1 | User interrupted the connection. | |--------------+---------------------------------------------| | 2 | Train sequence failed. | |--------------+---------------------------------------------| | 3 | Retrain sequence failed. | |--------------+---------------------------------------------| | 4 | Inactivity timer time limit reached. | |--------------+---------------------------------------------| | 5 | Long Space Disconnect time limit reached. | |--------------+---------------------------------------------| | 6 | Remote modem failed to respond to feature | | | negotiation. | +------------------------------------------------------------+ +------------------------------------------------------------+ | DIAL | |------------------------------------------------------------| | Type: | Immediate | |--------------+---------------------------------------------| | Format: | AT [cmds] D<#> [cmds] | |--------------+---------------------------------------------| | Description: | Dials the telephone number indicated | | | according to any modifiers included in the | | | string. | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | DJ | MNP10 link will be negotiated at 1200bps | | | for this call. | |--------------+---------------------------------------------| | DK | MNP10 power level adjustment enabled for | | | this call. | |--------------+---------------------------------------------| | DL | Re-dial last number. | |--------------+---------------------------------------------| | DP | Pulse dialing enabled. | |--------------+---------------------------------------------| | DR | Answer mode enabled; originate mode | | | disabled following handshake initiation. | |--------------+---------------------------------------------| | DS=n | Dial stored telephone number n. | |--------------+---------------------------------------------| | DT | Tone dialing enabled. | |--------------+---------------------------------------------| | DW | Dialing resumed following dial tone | | | detection. | |--------------+---------------------------------------------| | D, | Dialing paused for amount of time specified | | | in S8 register. | |--------------+---------------------------------------------| | D/ | Dialing paused for 1/8 second. | |--------------+---------------------------------------------| | D! | Flash function initiated. Modem commanded | | | to go off-hook for specified time before | | | returning on-hook. | |--------------+---------------------------------------------| | D@ | Wait for Quiet Answer function enabled. | | | Modem waits until a "quiet answer," a | | | ring-back signal followed by silence up to | | | the time specified in S7, is received prior | | | to executing the rest of the dial string. | |--------------+---------------------------------------------| | D; | Modem returned to idle state after dialing. | | | The semicolon can only be placed at the end | | | of the dial command. | +------------------------------------------------------------+ +------------------------------------------------------------+ | DISCONNECT BUFFER DELAY | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format | AT [cmds] %Dn [cmds] | |--------------+---------------------------------------------| | Default: | 20 | |--------------+---------------------------------------------| | Range: | 0-255 | |--------------+---------------------------------------------| | Unit: | .1 second | |--------------+---------------------------------------------| | Description: | Sets maximum duration allowed during | | | buffered data calls for modem to perform | | | clearing functions after losing | | | carrier-signal or receiving a clear call | | | signal from the remote modem and before | | | initiating hang-up process. A value of 0 | | | causes the modem to hang up without | | | waiting. | +------------------------------------------------------------+ +------------------------------------------------------------+ | DISPLAY INFORMATION | |------------------------------------------------------------| | Type: | Immediate | |--------------+---------------------------------------------| | Format: | AT [cmds] In [cmds] | |--------------+---------------------------------------------| | Description: | Displays information requested about the | | | modem. | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | I0 | Displays product identification code. | |--------------+---------------------------------------------| | I1 | Displays ROM checksum. | |--------------+---------------------------------------------| | I2 | Tests and reports ROM checksum. | |--------------+---------------------------------------------| | I3 | Displays firmware revision. | |--------------+---------------------------------------------| | I4 | Displays ASCII test string. | |--------------+---------------------------------------------| | I5 | Displays chipset revision. | +------------------------------------------------------------+ +------------------------------------------------------------+ | DISPLAY STORED PROFILES | |------------------------------------------------------------| | Type: | Immediate | |--------------+---------------------------------------------| | Format: | AT [cmds] \Sn [cmds] | |--------------+---------------------------------------------| | Description: | Displays the requested stored information. | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | \S0 | Displays stored profiles 0 and 1, and | | | stored numbers 0 - 2. | |--------------+---------------------------------------------| | \S1 | Displays stored profiles 2 and 3, and | | | stored numbers 0 - 3. | +------------------------------------------------------------+ +------------------------------------------------------------+ | DISPLAY STORED PROFILES | |------------------------------------------------------------| | Type: | Immediate | |--------------+---------------------------------------------| | Format: | AT [cmds] &Vn [cmds] | |--------------+---------------------------------------------| | Description: | Displays the requested stored information. | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | &V0 | Displays stored profiles 0 and 1, and | | | stored numbers 0 - 2. | |--------------+---------------------------------------------| | &V1 | Displays stored profiles 2 and 3, and | | | stored numbers 0 - 3. | +------------------------------------------------------------+ +------------------------------------------------------------+ | FLOW CONTROL | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] &Kn [cmds] | |--------------+---------------------------------------------| | Description: | Enables flow control options. | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | &K0 | Flow control disabled. | |--------------+---------------------------------------------| | i &K3 | RTS/CTS flow control enabled. | |--------------+---------------------------------------------| | &K4 | XON/XOFF flow control enabled. | |--------------+---------------------------------------------| | &K8 | Unidirectional transparent XON/XOFF flow | | | control enabled. | |--------------+---------------------------------------------| | &K12 | Local transparent XON/XOFF flow control | | | enabled. | |--------------+---------------------------------------------| | &K16 | Internal XON/XOFF flow control enabled. | |--------------+---------------------------------------------| | &K20 | Internal local XON/XOFF flow control | | | enabled. | +------------------------------------------------------------+ +------------------------------------------------------------+ | FLOW CONTROL CHARACTER - XON | |------------------------------------------------------------| | Type: | Register | |--------------+---------------------------------------------| | Format: | AT [cmds] S47=n [cmds] | |--------------+---------------------------------------------| | Default: | 17 | |--------------+---------------------------------------------| | Range: | 0-255 | |--------------+---------------------------------------------| | Unit: | 1 ASCII character | |--------------+---------------------------------------------| | Description: | Sets the character used to represent XON. | +------------------------------------------------------------+ +------------------------------------------------------------+ | FLOW CONTROL CHARACTER - XOFF | |------------------------------------------------------------| | Type: | Register | |--------------+---------------------------------------------| | Format: | AT [cmds] S48=n [cmds] | |--------------+---------------------------------------------| | Default: | 10 | |--------------+---------------------------------------------| | Range: | 0-255 | |--------------+---------------------------------------------| | Unit: | 1 ASCII character | |--------------+---------------------------------------------| | Description: | Sets the character used to represent XOFF. | +------------------------------------------------------------+ +------------------------------------------------------------+ | INACTIVITY TIMER | |------------------------------------------------------------| | Type: | Register | |--------------+---------------------------------------------| | Format: | AT [cmds] S40=n [cmds] | |--------------+---------------------------------------------| | Default: | 0 | |--------------+---------------------------------------------| | Range: | 0 - 255 | |--------------+---------------------------------------------| | Unit: | 1 minute | |--------------+---------------------------------------------| | Description: | Sets the length of time that the modem does | | | not receive information before it | | | disconnects; S40=0 will disable. | +------------------------------------------------------------+ +------------------------------------------------------------+ | LINE SPEED | |------------------------------------------------------------| | Type: | Register | |--------------+---------------------------------------------| | Format | AT [cmds] S37=n [cmds] | |--------------+---------------------------------------------| | Description: | Sets the maximum allowable data exchange | | | rate attempted during handshaking process. | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | i S37=0 | Speed of last connection | |--------------+---------------------------------------------| | S37=3 | Set speed to 300bps. | |--------------+---------------------------------------------| | S37=5 | Set speed to 1200bps. | |--------------+---------------------------------------------| | S37=6 | Set speed to 2400bps. | |--------------+---------------------------------------------| | S37=7 | Set speed to 4800bps. | |--------------+---------------------------------------------| | S37=9 | Set speed to 9600bps. | |--------------+---------------------------------------------| | S37=10 | Set speed to 9600bps. | |--------------+---------------------------------------------| | S37=11 | Set speed to 300bps. | |--------------+---------------------------------------------| | S37=15 | Set speed to 4800bps. | |--------------+---------------------------------------------| | S37=16 | Set speed to 7200bps. | |--------------+---------------------------------------------| | S37=17 | Set speed to 9600bps. | |--------------+---------------------------------------------| | S37=18 | Set speed to 12Kbps. | |--------------+---------------------------------------------| | S37=19 | Set speed to 14.4Kbps. | +------------------------------------------------------------+ +------------------------------------------------------------+ | LOCK SERIAL PORT | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] &Bn [cmds] | |--------------+---------------------------------------------| | Description: | Sets operation of serial port speed. | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | &B0 | Serial speed follows connect speed. | |--------------+---------------------------------------------| | i &B1 | Serial speed locked. | +------------------------------------------------------------+ +------------------------------------------------------------+ | TRANSMISSION LEVEL ATTENUATION - LEASED LINE | |------------------------------------------------------------| | Type | Register | |-------------+----------------------------------------------| | Format | AT [cmds] S35=n [cmds] | |-------------+----------------------------------------------| | Default | 9 | |-------------+----------------------------------------------| | Range | 0 - 15 | |-------------+----------------------------------------------| | Unit | -1 dBm | |-------------+----------------------------------------------| | Description | Sets the signal attenuation level for | | | transmission over leased phone lines. | +------------------------------------------------------------+ +------------------------------------------------------------+ | V.32 - COMPROMISE EQUALIZER | |------------------------------------------------------------| | Type% | Configuration | |--------------+---------------------------------------------| | Format% | AT [cmds] %En [cmds] | |--------------+---------------------------------------------| | Description% | Controls V.32 compromise equalizer. | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | %E0 | Compromise equalizer disabled. | |--------------+---------------------------------------------| | %E1 | Compromise equalizer enabled. |