APACHE MICRO PERIPHERALS, INC. ============================== APACHE V34IV-SP+ Card Type Modem (synchronous/asynchronous) Chip Set Unidentified I/O Options Voice, speakerphone Maximum Data Rate 33.6Kbps Maximum Fax Rate 14.4Kbps Data Bus Unidentified Fax Class Class I & II Data Modulation Bell 103A/212A Protocol ITU-T V.21, V.22, V.22bis, V.23, V.32, V.32bis, V.34 Rockwell V.FC Fax Modulation Unidentified Protocol Error MNP5, V.42, V.42bis, RPI Correction/Compression 52997 +------------------------------------------------------------+ | USER CONFIGURABLE SETTINGS | |------------------------------------------------------------| | Setting | Label | Position | |-------------------------------------+-------+--------------| | i Factory configured - do not alter | SW1/7 | Unidentified | |-------------------------------------+-------+--------------| | i Factory configured - do not alter | SW1/8 | N/A | |------------------------------------------------------------| | Note: SW1/8 may not be present on all models. | +------------------------------------------------------------+ +------------------------------------------------------------+ | INTERRUPT SELECTION | |------------------------------------------------------------| | Setting | SW1/1 | SW1/2 | SW1/3 | SW1/4 | |------------+-----------+-----------+-----------+-----------| | i IRQ3 | Off | Off | Off | On | |------------+-----------+-----------+-----------+-----------| | IRQ4 | Off | Off | On | Off | |------------+-----------+-----------+-----------+-----------| | IRQ5 | Off | On | Off | Off | |------------+-----------+-----------+-----------+-----------| | IRQ7 | On | Off | Off | Off | +------------------------------------------------------------+ +------------------------------------------------------------+ | SERIAL PORT ADDRESS SELECTION | |------------------------------------------------------------| | Setting | SW1/5 | SW1/6 | |--------------------+-------------------+-------------------| | 3F8h (COM1:) | On | On | |--------------------+-------------------+-------------------| | 2F8h (COM2:) | Off | On | |--------------------+-------------------+-------------------| | 3E8h (COM3:) | On | Off | |--------------------+-------------------+-------------------| | i 2E8h (COM4:) | Off | Off | +------------------------------------------------------------+ +------------------------------+ | MISCELLANEOUS TECHNICAL NOTE | |------------------------------| | Diagram not available. | +------------------------------+ +------------------------------------------------------------+ | SUPPORTED STANDARD COMMANDS | |------------------------------------------------------------| | Basic AT Commands | |------------------------------------------------------------| | +++, 'comma', A/ | |------------------------------------------------------------| | A, B, D, E, H, L, M, N, O, P, Q, T, V, W, X, Y | |------------------------------------------------------------| | &C, &D, &F, &G, &K, &M, &P, &Q, &R, &S, &T, &V, &W, &X, | | &Y, &Z | |------------------------------------------------------------| | Extended AT Commands | |------------------------------------------------------------| | \A, \B, \K, \N, \V | |------------------------------------------------------------| | %C, %E, %F, %L, %Q, %TT | |------------------------------------------------------------| | Special AT Commands | |------------------------------------------------------------| | #CID, +MS | |------------------------------------------------------------| | S-Registers | |------------------------------------------------------------| | The S-registers are unidentified. | |------------------------------------------------------------| | Note: See MHI documentation for complete information. | +------------------------------------------------------------+ Proprietary AT Command Set +------------------------------------------------------------+ | DISPLAY MANUFACTURER | |------------------------------------------------------------| | Type: | Immediate | |--------------+---------------------------------------------| | Format: | AT [cmds] #MFR? [cmds] | |--------------+---------------------------------------------| | Description: | Displays the manufacturer's name. | +------------------------------------------------------------+ +------------------------------------------------------------+ | DISPLAY MODEL NAME | |------------------------------------------------------------| | Type: | Immediate | |--------------+---------------------------------------------| | Format: | AT [cmds] #MDL? [cmds] | |--------------+---------------------------------------------| | Description: | Displays the model name of the modem. | +------------------------------------------------------------+ +------------------------------------------------------------+ | DISPLAY REVISION | |------------------------------------------------------------| | Type: | Immediate | |--------------+---------------------------------------------| | Format: | AT [cmds] #REV? [cmds] | |--------------+---------------------------------------------| | Description: | Displays the revision level of the modem. | +------------------------------------------------------------+ +------------------------------------------------------------+ | DISTINCTIVE RING | |------------------------------------------------------------| | Format: | AT [cmds] -SDR=n [cmds] | |----------------+-------------------------------------------| | Default: | Unidentified | |----------------+-------------------------------------------| | Range: | 0 - 7 | |----------------+-------------------------------------------| | Description: | Selects which distinctive ring signals | | | the modem will respond to. | |------------------------------------------------------------| | Bit | Value | Function | |---------+-------+------------------------------------------| | 0 | 0 | Do not respond to distinctive ring type | | | | 1. | | | 1 | | | | | Respond to distinctive ring type 1. | |------------------------------------------------------------| | 1 | 0 | Do not respond to distinctive ring type | | | | 2. | | | 1 | | | | | Respond to distinctive ring type 2. | |-------------+----+-----------------------------------------| | 2 | 0 | Do not respond to distinctive ring type | | | | 3. | | | 1 | | | | | Respond to distinctive ring type 3. | +------------------------------------------------------------+ +------------------------------------------------------------+ | DSVD MODE | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] -SSE=n [cmds] | |--------------+---------------------------------------------| | Description: | Select whether the modem will use DSVD | | | mode. | |------------------------------------------------------------| | Command | Function | |---------------------------+--------------------------------| | i -SSE=0 | DSVD mode disabled. | |---------------------------+--------------------------------| | -SSE=1 | DSVD mode enabled. | +------------------------------------------------------------+ +------------------------------------------------------------+ | FIRMWARE DOWNLOAD | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] **n [cmds] | |--------------+---------------------------------------------| | Description: | Downloads new code to the firmware flash | | | memory. | |------------------------------------------------------------| | Command | Function | |-----------------+------------------------------------------| | **0 | Download at speed of last command. | |-----------------+------------------------------------------| | **1 | Download at 38.4Kbps. | |-----------------+------------------------------------------| | **2 | Download at 57.6Kbps. | +------------------------------------------------------------+ +------------------------------------------------------------+ | MODE SELECTION | |------------------------------------------------------------| | Type: | Immediate | |--------------+---------------------------------------------| | Format: | AT [cmds] #CLS=n [cmds] | |--------------+---------------------------------------------| | Description: | Selects which mode the modem will operate | | | in. | |------------------------------------------------------------| | Command | Function | |---------------+--------------------------------------------| | #CLS=0 | Modem will operate in data mode. | |---------------+--------------------------------------------| | #CLS=1 | Modem will operate in fax class I mode. | |---------------+--------------------------------------------| | #CLS=2 | Modem will operate in fax class II mode. | |---------------+--------------------------------------------| | #CLS=8 | Modem will operate in voice mode. | +------------------------------------------------------------+ +------------------------------------------------------------+ | PROTOCOL/SPEED | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] Fn [cmds] | |--------------+---------------------------------------------| | Description: | Selects the protocol and speed the modem | | | will attempt to connect at. | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | F0 | Auto-detect the highest common connect | | | speed. | |--------------+---------------------------------------------| | F1 | Select V.21 or Bell 103 at 300bps speed. | |--------------+---------------------------------------------| | F3 | Select V.23 at 75/1200bps speed. | |--------------+---------------------------------------------| | F4 | Select V.22 or Bell 212A at 1200bps speed. | |--------------+---------------------------------------------| | F5 | Select V.22bis at 2400bps speed. | |--------------+---------------------------------------------| | F6 | Select V.32 or V.32bis at 4800bps speed. | |--------------+---------------------------------------------| | F7 | Select V.32bis at 7200bps speed. | |--------------+---------------------------------------------| | F8 | Select V.32bis or V.32 at 9600bps speed. | |--------------+---------------------------------------------| | F9 | Select V.32bis at 12Kbps speed. | |--------------+---------------------------------------------| | F10 | Select V.32bis at 14.4Kbps speed. | +------------------------------------------------------------+ +------------------------------------------------------------+ | REPORT INFORMATION | |------------------------------------------------------------| | Type: | Immediate | |--------------+---------------------------------------------| | Format: | AT [cmds] In [cmds] | |--------------+---------------------------------------------| | Description: | Displays requested information about the | | | modem. | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | I0 | Reports product identification code. | |--------------+---------------------------------------------| | I1 | Reports ROM checksum. | |--------------+---------------------------------------------| | I2 | Tests and reports ROM checksum. | |--------------+---------------------------------------------| | I3 | Reports modem firmware version and | | | interface type. | |--------------+---------------------------------------------| | I4 | Reports OEM response. | |--------------+---------------------------------------------| | I5 | Reports country code. | |--------------+---------------------------------------------| | I6 | Reports data pump model and revision. | |--------------+---------------------------------------------| | I7 | Reports DAA code. | +------------------------------------------------------------+ +------------------------------------------------------------+ | RPI CONFIGURATION | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] +Hn [cmds] | |--------------+---------------------------------------------| | Description: | Configures the Rockwell Protocol Interface. | |------------------------------------------------------------| | Command | Function | |-----------------+------------------------------------------| | +H0 | RPI disabled. | |-----------------+------------------------------------------| | +H1 | RPI enabled and local serial port speed | | | set to 19.2Kbps. | |-----------------+------------------------------------------| | +H2 | RPI enabled and local serial port speed | | | set to 38.4Kbps. | |-----------------+------------------------------------------| | +H3 | RPI enabled and local serial port speed | | | set to 57.6Kbps. | |-----------------+------------------------------------------| | +H11 | RPI+ enabled. | +------------------------------------------------------------+ +------------------------------------------------------------+ | SPEAKERPHONE OPTIONS | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] #SPK=x,y,z [cmds] | |--------------+---------------------------------------------| | Description: | Sets various options for speakerphone | | | functions. | |------------------------------------------------------------| | Command | Function | |---------------+--------------------------------------------| | x=0 | Microphone enabled. | |---------------+--------------------------------------------| | x=1 | Microphone disabled. | |---------------+--------------------------------------------| | x=2 | Microphone enabled with maximum gain, | | | speaker disabled. | |------------------------------------------------------------| | Default (y): | 5 | |--------------+---------------------------------------------| | Range (y): | 0 - 16 | |--------------+---------------------------------------------| | Unit (y): | -2 dBm | |--------------+---------------------------------------------| | Description | Sets the attenuation level for speaker | | (y): | output in voice mode. | |------------------------------------------------------------| | z=0 | Microphone gain set to 0 dBm. | |---------------+--------------------------------------------| | z=1 | Microphone gain set to 6 dBm. | |---------------+--------------------------------------------| | z=2 | Microphone gain set to 9.5 dBm. | |---------------+--------------------------------------------| | z=3 | Microphone gain set to 12 dBm. | +------------------------------------------------------------+ +------------------------------------------------------------+ | TONE DETECTION | |------------------------------------------------------------| | Format: | AT [cmds] #VTD=x,y,z [cmds] | |----------------+-------------------------------------------| | Default: | x,y,z 63 | |----------------+-------------------------------------------| | Range: | 0 - 63 | |----------------+-------------------------------------------| | Description: | Sets which tones the tone detection will | | | report. | |----------------+-------------------------------------------| | Note: | The value of x sets the tone detection | | | modes in voice transmit mode, y sets them | | | in voice receive mode, and z sets them in | | | voice command mode. | |------------------------------------------------------------| | Bit | Value | Function | |---------+-------+------------------------------------------| | 0 | 0 | DTMF tones are not detected. | | | | | | | i 1 | DTMF tones are detected. | |------------------------------------------------------------| | 1 | 0 | V.25 1300Hz calling tone is not | | | | detected. | | | i | | | | 1 | V.25 1300Hz calling tone is detected. | |-------------+----+-----------------------------------------| | 2 | 0 | T.30 1100Hz fax tone is not detected. | | | | | | | i | T.30 1100Hz fax tone is detected. | | | 1 | | |-------------+----+-----------------------------------------| | 3 | 0 | V.25/T.30 2100Hz answer tone is not | | | | detected. | | | i | | | | 1 | V.25/T.30 2100Hz answer tone is | | | | detected. | |-------------+----+-----------------------------------------| | 4 | 0 | Bell 2225Hz answer tone is not | | | | detected. | | | i | | | | 1 | Bell 2225Hz answer tone is detected. | |-------------+----+-----------------------------------------| | 5 | 0 | Call progress tones are not detected. | | | | | | | i | Call progress tones are detected. | | | 1 | | +------------------------------------------------------------+ +------------------------------------------------------------+ | TONE GENERATOR - DIRECT ENTRY | |------------------------------------------------------------| | Type: | Immediate | |--------------+---------------------------------------------| | Format: | AT [cmds] #VTS=[m, n, x] | |--------------+---------------------------------------------| | Range: | m 200-3000, n 200-3000, x 0-255 | |--------------+---------------------------------------------| | Unit: | m 1 Hz, n 1 Hz, x .1 second | |--------------+---------------------------------------------| | Description: | Generates a dual-frequency tone for | | | duration x at frequencies m and n. | +------------------------------------------------------------+ +------------------------------------------------------------+ | TONE GENERATOR - TIMED PHONE KEYS | |------------------------------------------------------------| | Type: | Immediate | |--------------+---------------------------------------------| | Format: | AT [cmds] #VTS={a, n} | |--------------+---------------------------------------------| | Range: | a 0-9, A-D, #, *; x 0-255 | |--------------+---------------------------------------------| | Unit: | x .1 second | |--------------+---------------------------------------------| | Description: | Generates the DTMF tone for duration x for | | | the character a. | +------------------------------------------------------------+ +------------------------------------------------------------+ | TONE GENERATOR - PHONE KEYS | |------------------------------------------------------------| | Type: | Immediate | |--------------+---------------------------------------------| | Format: | AT [cmds] #VTS=a | |--------------+---------------------------------------------| | Range: | 0-9, A-D, #, * | |--------------+---------------------------------------------| | Description: | Generates the DTMF tones for the characters | | | in the string for the duration set with | | | +VBT. | +------------------------------------------------------------+ +------------------------------------------------------------+ | TONE GENERATOR LENGTH | |------------------------------------------------------------| | Format | AT [cmds] #VBT=n [cmds] | |--------------+---------------------------------------------| | Default: | 10 | |--------------+---------------------------------------------| | Range: | 0 - 40 | |--------------+---------------------------------------------| | Unit: | 0.1 second | |--------------+---------------------------------------------| | Description: | Sets the length of DTMF tones that are | | | generated. | +------------------------------------------------------------+ +------------------------------------------------------------+ | VOICE BUFFER SPACE | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] #VSK=n [cmds] | |--------------+---------------------------------------------| | Default: | 255 | |--------------+---------------------------------------------| | Range: | 0 - 255 | |--------------+---------------------------------------------| | Unit: | 1 byte | |--------------+---------------------------------------------| | Description: | Sets the amount of data the modem can send | | | into the buffer after the XOFF signal is | | | sent. | +------------------------------------------------------------+ +------------------------------------------------------------+ | VOICE DEVICE | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] #VLS=n [cmds] | |--------------+---------------------------------------------| | Description: | Selects the I/O device for the DSP chip. | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | i #VLS=0 | Telephone line and handset used for voice | | | I/O. | |--------------+---------------------------------------------| | #VLS=1 | Telephone handset used for voice I/O. | |--------------+---------------------------------------------| | #VLS=2 | Internal speaker only used for voice I/O. | |--------------+---------------------------------------------| | #VLS=3 | External microphone only used for voice | | | I/O. | |--------------+---------------------------------------------| | #VLS=4 | Telephone line and handset used for voice | | | I/O; internal speaker enabled. | |--------------+---------------------------------------------| | #VLS=5 | Headset used for voice I/O. | |--------------+---------------------------------------------| | #VLS=6 | Speakerphone used for voice I/O. | +------------------------------------------------------------+ +------------------------------------------------------------+ | VOICE - DISPLAY BUFFER SIZE | |------------------------------------------------------------| | Type: | Immediate | |--------------+---------------------------------------------| | Format: | AT [cmds] #VBQ? [cmds] | |--------------+---------------------------------------------| | Description: | Displays the size of the voice buffer. | +------------------------------------------------------------+ +------------------------------------------------------------+ | VOICE - DISPLAY COMPRESSION TYPE | |------------------------------------------------------------| | Type: | Immediate | |--------------+---------------------------------------------| | Format: | AT [cmds] #VCI? [cmds] | |--------------+---------------------------------------------| | Description: | Displays the type of compression currently | | | in use. | +------------------------------------------------------------+ +------------------------------------------------------------+ | VOICE - LOCAL SERIAL PORT SPEED | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] #BDR=n [cmds] | |--------------+---------------------------------------------| | Description: | Sets the speed of the local serial port | | | when in voice mode. | |------------------------------------------------------------| | Command | Function | |-----------------------+------------------------------------| | #BDR=1 | Set speed to 2400bps. | |-----------------------+------------------------------------| | #BDR=2 | Set speed to 4800bps. | |-----------------------+------------------------------------| | #BDR=4 | Set speed to 9600bps. | |-----------------------+------------------------------------| | #BDR=6 | Set speed to 14.4Kbps. | |-----------------------+------------------------------------| | #BDR=8 | Set speed to 19.2Kbps. | |-----------------------+------------------------------------| | #BDR=16 | Set speed to 38.4Kbps. | |-----------------------+------------------------------------| | #BDR=24 | Set speed to 57.6Kbps. | +------------------------------------------------------------+ +------------------------------------------------------------+ | VOICE RE-RING DETECT TIME | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] #VRA=n [cmds] | |--------------+---------------------------------------------| | Default: | 70 | |--------------+---------------------------------------------| | Range: | 0-255 | |--------------+---------------------------------------------| | Unit: | 10 mS | |--------------+---------------------------------------------| | Description: | Sets the maximum time the modem will wait | | | for the remote station to ring again before | | | it assumes that it has gone off-hook. | +------------------------------------------------------------+ +------------------------------------------------------------+ | VOICE RECEIVE | |------------------------------------------------------------| | Type: | Immediate | |--------------+---------------------------------------------| | Format: | AT [cmds] #VRX | |--------------+---------------------------------------------| | Description: | Commands the modem to begin receiving voice | | | data. | +------------------------------------------------------------+ +------------------------------------------------------------+ | VOICE RING DETECT TIME | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] #VRN=n [cmds] | |--------------+---------------------------------------------| | Default: | Unidentified | |--------------+---------------------------------------------| | Range: | Unidentified | |--------------+---------------------------------------------| | Unit: | Unidentified | |--------------+---------------------------------------------| | Description: | Sets the maximum time the modem will wait | | | for the remote station to ring before it | | | assumes that it went off-hook before it | | | rang. | +------------------------------------------------------------+ +------------------------------------------------------------+ | VOICE SAMPLE QUALITY | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] #VBS=n [cmds] | |--------------+---------------------------------------------| | Description: | Selects the number of bits per sample that | | | the modem records. | |------------------------------------------------------------| | Command | Function | |----------------+-------------------------------------------| | #VBS=2 | Modem records 2 bits per sample in ADPCM | | | encoding. | |----------------+-------------------------------------------| | #VBS=3 | Modem records 3 bits per sample in ADPCM | | | encoding. | |----------------+-------------------------------------------| | i #VBS=4 | Modem records 4 bits per sample in ADPCM | | | encoding. | +------------------------------------------------------------+ +------------------------------------------------------------+ | VOICE SAMPLING RATE | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] #VSR=n [cmds] | |--------------+---------------------------------------------| | Description: | Sets the sampling rate used when recording | | | voice signals. | |------------------------------------------------------------| | Command | Function | |----------------+-------------------------------------------| | #VSR=7200 | Selects a sampling rate of 7.2KHz. | |----------------+-------------------------------------------| | #VSR=11025 | Selects a sampling rate of 11.025KHz in | | | PCM encoding only. | +------------------------------------------------------------+ +------------------------------------------------------------+ | VOICE SILENCE DETECTION TIME | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] #VSP=n [cmds] | |--------------+---------------------------------------------| | Default: | Unidentified | |--------------+---------------------------------------------| | Range: | 0 - 255 | |--------------+---------------------------------------------| | Unit: | .1 second | |--------------+---------------------------------------------| | Description: | Sets the minimum amount of silence that the | | | modem will detect. | +------------------------------------------------------------+ +------------------------------------------------------------+ | VOICE SILENCE DETECTION THRESHOLD | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] #VSS=n [cmds] | |--------------+---------------------------------------------| | Description: | Sets the threshold of sensitivity that the | | | modem uses to determine silence detection. | |------------------------------------------------------------| | Command | Function | |----------------+-------------------------------------------| | #VSS=0 | Silence detection disabled. | |----------------+-------------------------------------------| | #VSS=1 | Minimum silence detection sensitivity. | |----------------+-------------------------------------------| | #VSS=2 | Standard silence detection sensitivity. | |----------------+-------------------------------------------| | #VSS=3 | Maximum silence detection sensitivity. | +------------------------------------------------------------+ +------------------------------------------------------------+ | VOICE TIMING MARK | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] #VTM=n [cmds] | |--------------+---------------------------------------------| | Description: | Configures timing mark placement. | |------------------------------------------------------------| | Command | Function | |---------------------+--------------------------------------| | #VTM=0 | Timing marks disabled. | |---------------------+--------------------------------------| | #VTM=1 | Timing marks enabled. | +------------------------------------------------------------+ +------------------------------------------------------------+ | VOICE TRANSMISSION LEVEL | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] #TL=hhhh [cmds] | |--------------+---------------------------------------------| | Default: | 3FFF | |--------------+---------------------------------------------| | Range: | 0000 - 7FFF | |--------------+---------------------------------------------| | Unit: | Unidentified (hexadecimal) | |--------------+---------------------------------------------| | Description: | Sets the transmission level for sending | | | audio in voice mode. | +------------------------------------------------------------+ +------------------------------------------------------------+ | VOICE TRANSMIT | |------------------------------------------------------------| | Type: | Immediate | |--------------+---------------------------------------------| | Format: | AT [cmds] #VTX | |--------------+---------------------------------------------| | Description: | Commands the modem to begin transmitting | | | voice data. | +------------------------------------------------------------+ +------------------------------------------------------------+ | VOICE VOLUME LEVEL | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] #VGT=n [cmds] | |--------------+---------------------------------------------| | Description: | Sets the volume level when playing back | | | audio signals. |