APACHE MICRO PERIPHERALS, INC. ============================== SEVEL V34I-V+/C, SEVEL V34IV-SP+/C Card Type Modem (asynchronous) Chip Set Cirrus Logic I/O Options Speakerphone (Sevel V34IV-SP+/C only), voice Maximum Data Rate 33.6Kbps Maximum Fax Rate 14.4Kbps Data Bus 16-bit ISA Fax Class Class I Data Modulation ITU-T V.32bis, V.34 Protocol U.S. Robotics x2 Rockwell V.FC Fax Modulation Unidentified Protocol Error MNP5, V.42, V.42bis Correction/Compression +------------------------------------------------------------+ | CONNECTIONS | |------------------------------------------------------------| | Function | Label | Function | Label | |------------------------------------------------------------| | Line in | CN1 | Unidentified | CN3 | |---------------------------+----------+--------------+------| | Line out | CN2 | Unidentified | CN4 | +------------------------------------------------------------+ +------------------------------------------------------------+ | USER CONFIGURABLE SETTINGS | |------------------------------------------------------------| | Setting | Label | Position | |-------------------------------------+-------+--------------| | i Factory configured - do not alter | SW1/7 | Unidentified | |-------------------------------------+-------+--------------| | i Factory configured - do not alter | SW1/8 | N/A | |------------------------------------------------------------| | Note: SW1/8 may not be present on all models. | +------------------------------------------------------------+ +------------------------------------------------------------+ | SERIAL PORT ADDRESS SELECTION | |------------------------------------------------------------| | Setting | SW1/5 | SW1/6 | |--------------------+-------------------+-------------------| | 3F8h (COM1:) | On | On | |--------------------+-------------------+-------------------| | 2F8h (COM2:) | Off | On | |--------------------+-------------------+-------------------| | 3E8h (COM3:) | On | Off | |--------------------+-------------------+-------------------| | i 2E8h (COM4:) | Off | Off | +------------------------------------------------------------+ +------------------------------------------------------------+ | INTERRUPT SELECTION | |------------------------------------------------------------| | Setting | SW1/1 | SW1/2 | SW1/3 | SW1/4 | |------------+-----------+-----------+-----------+-----------| | i IRQ3 | Off | Off | Off | On | |------------+-----------+-----------+-----------+-----------| | IRQ4 | Off | Off | On | Off | |------------+-----------+-----------+-----------+-----------| | IRQ5 | Off | On | Off | Off | |------------+-----------+-----------+-----------+-----------| | IRQ7 | On | Off | Off | Off | +------------------------------------------------------------+ +------------------------------------------------------------+ | PLUG-N-PLAY SELECTION | |------------------------------------------------------------| | Setting | JP1 | JP2 | JP3 | JP4 | JP5 | |----------+---------+---------+---------+---------+---------| | i | Pins 1 | Pins 1 | Pins 1 | Pins 1 | Pins 1 | | Disabled | & 2 | & 2 | & 2 | & 2 | & 2 | |----------+---------+---------+---------+---------+---------| | Enabled | Pins 2 | Pins 2 | Pins 2 | Pins 2 | Pins 2 | | | & 3 | & 3 | & 3 | & 3 | & 3 | +------------------------------------------------------------+ +------------------------------------------------------------+ | PLUG-N-PLAY SELECTION (CON'T) | |------------------------------------------------------------| | Setting | JP6 | JP7 | JP8 | JP9 | JP10 | |----------+---------+---------+---------+---------+---------| | i | Pins 1 | Pins 1 | Pins 1 | Pins 1 | Pins 1 | | Disabled | & 2 | & 2 | & 2 | & 2 | & 2 | |----------+---------+---------+---------+---------+---------| | Enabled | Pins 2 | Pins 2 | Pins 2 | Pins 2 | Pins 2 | | | & 3 | & 3 | & 3 | & 3 | & 3 | |------------------------------------------------------------| | Note: SW1/1 through SW1/8 must all be off in | | Plug-N-Play mode. | +------------------------------------------------------------+ +------------------------------------------------------------+ | SUPPORTED STANDARD COMMANDS | |------------------------------------------------------------| | Basic AT Commands | |------------------------------------------------------------| | +++, 'comma', A/ | |------------------------------------------------------------| | A, D, E, F, H, L, M, N, O, Q, V, W, X, Y, Z | |------------------------------------------------------------| | &C, &D, &F, &G, &J, &K, &P, &S, &T, &W, &Y, &Z | |------------------------------------------------------------| | Extended AT Commands | |------------------------------------------------------------| | \A, \B, \C, \G, \J, \N, \O, \Q, \T, \U, \X, \Y, \Z | |------------------------------------------------------------| | %A, %C, %E, %G, %L, %Q | |------------------------------------------------------------| | Special AT Commands | |------------------------------------------------------------| | -J, "H, +MS, "O | |------------------------------------------------------------| | S-Registers | |------------------------------------------------------------| | S0, S1, S2, S3, S4, S5, S6, S7, S8, S9, S10, S11, S12, | | S14, S16, S18, S21, S22, S23, S25, S30 | |------------------------------------------------------------| | Note: See MHI documentation for complete information. | +------------------------------------------------------------+ Proprietary AT Command Set +------------------------------------------------------------+ | BIT-MAPPED REGISTER S27 | |------------------------------------------------------------| | Format | AT [cmds] S27=n [cmds] | |--------------+---------------------------------------------| | Default: | 0 | |--------------+---------------------------------------------| | Range: | 0 - 224 | |--------------+---------------------------------------------| | Unit: | Bit-mapped | |--------------+---------------------------------------------| | Description: | Selects synchronous/asynchronous mode, line | | | type, clock source, and ITU-T/Bell modes. | |--------------+---------------------------------------------| | Bit | Value | Function | |------+-------+---------------------------------------------| | 3 - | 0000 | Not used. | | 0 | | | |------+-------+---------------------------------------------| | 5, 4 | i 00 | Local modem generates transmit clock | | | | source. | | | 01 | | | | | Local DTE generates transmit clock source. | | | 10 | | | | | Remote DCE/DTE generates transmit clock | | | | source. | |------+-------+---------------------------------------------| | 7, 6 | i 00 | Use ITU-T V.22 at 300 or 1200bps | | | | | | | 01 | Use Bell 212A at 300 or 1200bps | | | | | | | 10 | Use ITU-T V.23 at 75/1200bps. | | | | | | | 11 | Use ITU-T V.23 at 1200/75bps. | +------------------------------------------------------------+ +------------------------------------------------------------+ | BIT-MAPPED REGISTER S31 | |------------------------------------------------------------| | Format: | AT [cmds] S31=n [cmds] | |----------------+-------------------------------------------| | Default: | Unidentified | |----------------+-------------------------------------------| | Range: | 0 - 59 | |----------------+-------------------------------------------| | Description: | | |------------------------------------------------------------| | Bit | Value | Function | |---------+-------+------------------------------------------| | 0 | 0 | Auto-mode detection disabled. | | | | | | | i 1 | In originate mode, handshake begins at | | | | line speed designated by the S37 | | | | register. Modem can shift to a slower | | | | speed if necessary. | | | | | | | | In answer mode, handshake attempted with | | | | the following protocols in order - V.FC, | | | | V.32bis, V.32, V.22bis, V.22 or Bell | | | | 212, V.21, and Bell 103. | |------------------------------------------------------------| | 1 | 0 | Trellis coding disabled. | | | | | | | 1 | Trellis coding enabled. | |-------------+----+-----------------------------------------| | 2 | 0 | Not used. | |-------------+----+-----------------------------------------| | 3 | i | Calling tone disabled. | | | 0 | | | | | 1300Hz calling tone enabled. | | | 1 | | |-------------+----+-----------------------------------------| | 4 | i | Auto-retrain disabled. | | | 0 | | | | | Auto-retrain enabled. | | | 1 | | |-------------+----+-----------------------------------------| | 5 | 0 | Auto-fallback/fall-forward disabled. | | | | | | | 1 | Auto-fallback/fall-forward enabled. | +------------------------------------------------------------+ +----------------------------------------------------------------+ | BREAK TYPE | |----------------------------------------------------------------| |Type: |Configuration | |------------------+---------------------------------------------| |Format: |AT [cmds] \Kn [cmds] | |------------------+---------------------------------------------| |Description: |Configures action of break signal. | |----------------------------------------------------------------| | Command |Break from DTE | Break from | Modem | Break from | | | | DTE |receives \B |remote modem| | |Reliable/Normal| | | | | | mode |Direct mode | | | |---------+---------------+------------+------------+------------| | \K0 |Enter command |Send break |Buffers |Buffers | | |mode, do not |to remote |cleared and |cleared and | | |send break to |modem |break sent |break sent | | |remote modem. |immediately,|to remote |to DTE. | | | |then enter |modem. | | | | |command | | | | | |mode. | | | |---------+---------------+------------+------------+------------| | \K1 |Buffers cleared|Send break |Buffers |Buffers | | |and break sent |to remote |cleared and |cleared and | | |to remote |modem |break sent |break sent | | |modem. |immediately.|to remote |to DTE. | | | | |modem. | | |---------+---------------+------------+------------+------------| | \K2 |Enter command |Send break |Send break |Send break | | |mode, do not |to remote |to remote |to DTE | | |send break to |modem |modem |immediately.| | |remote modem. |immediately,|immediately.| | | | |then enter | | | | | |command | | | | | |mode. | | | |---------+---------------+------------+------------+------------| | \K3 |Send break to |Send break |Send break |Send break | | |remote modem |to remote |to remote |to DTE | | |immediately. |modem |modem |immediately.| | | |immediately.|immediately.| | |---------+---------------+------------+------------+------------| | \K4 |Enter command |Send break |Send break |Break sent | | |mode, do not |to remote |to remote |with | | |send break to |modem |modem with |received | | |remote modem. |immediately,|transmitted |data to the | | | |then enter |data. |DTE. | | | |command | | | | | |mode. | | | |---------+---------------+------------+------------+------------| | \K5 |Send break with|Send break |Send break |Break sent | | |transmitted |to remote |to remote |with | | |data. |modem |modem with |received | | | |immediately.|transmitted |data to the | | | | |data. |DTE. | +----------------------------------------------------------------+ +------------------------------------------------------------+ | CALLER ID | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] +VCID=n [cmds] | |--------------+---------------------------------------------| | Description: | Controls the Caller ID function. | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | +VCID=0 | Caller ID disabled. | |--------------+---------------------------------------------| | +VCID=1 | Caller ID displays formatted data. | |--------------+---------------------------------------------| | +VCID=2 | Caller ID displays raw hexadecimal data. | +------------------------------------------------------------+ +------------------------------------------------------------+ | CALLING TONE | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] -Cn [cmds] | |--------------+---------------------------------------------| | Description: | Controls which calling tone the modem will | | | send a originating a call. | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | -C0 | Calling tone disabled. | |--------------+---------------------------------------------| | -C1 | 1300Hz calling tone enabled. | |--------------+---------------------------------------------| | -C2 | V.8 and 1300Hz calling tones enabled. | +------------------------------------------------------------+ +------------------------------------------------------------+ | COMMUNICATION PROTOCOLS | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] Bn [cmds] | |--------------+---------------------------------------------| | Description: | Selects the communication protocol for data | | | calls | |--------------+---------------------------------------------| | Command | Protocol | |--------------+---------------------------------------------| | B0 | ITU-T V.22 at 300 or 1200bps | |--------------+---------------------------------------------| | i B1 | Bell 212A at 300 or 1200bps | |--------------+---------------------------------------------| | B2 | ITU-T V.23 at 75/1200bps. | |--------------+---------------------------------------------| | B3 | ITU-T V.23 at 1200/75bps. | +------------------------------------------------------------+ +------------------------------------------------------------+ | DISPLAY MANUFACTURER | |------------------------------------------------------------| | Type: | Immediate | |--------------+---------------------------------------------| | Format: | AT [cmds] +GMI? [cmds] | |--------------+---------------------------------------------| | Description: | Displays the manufacturer's name. | +------------------------------------------------------------+ +------------------------------------------------------------+ | DISPLAY MODEL NAME | |------------------------------------------------------------| | Type: | Immediate | |--------------+---------------------------------------------| | Format: | AT [cmds] +GMM? [cmds] | |--------------+---------------------------------------------| | Description: | Displays the model name of the modem. | +------------------------------------------------------------+ +------------------------------------------------------------+ | DISPLAY REVISION | |------------------------------------------------------------| | Type: | Immediate | |--------------+---------------------------------------------| | Format: | AT [cmds] +GMR? [cmds] | |--------------+---------------------------------------------| | Description: | Displays the revision level of the modem. | +------------------------------------------------------------+ +------------------------------------------------------------+ | DISPLAY STORED PROFILE AND STATUS | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] &Vn [cmds] | |--------------+---------------------------------------------| | Description: | Displays the command settings in the stored | | | profiles and information about the current | | | modem I/O status. | |------------------------------------------------------------| | Command | Function | |-----------------+------------------------------------------| | &V0 | Display profile 0. | |-----------------+------------------------------------------| | &V1 | Display profile 1. | |-----------------+------------------------------------------| | &V3 | Display general I/O and relay status. | +------------------------------------------------------------+ +------------------------------------------------------------+ | EXTENDED RESULT CODES | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] Wn [cmds] | |--------------+---------------------------------------------| | Description: | Enables selection of additional result | | | codes when S95=0; otherwise, S95 takes | | | precedence. | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | i W0 | Enables CONNECT result codes to report DTE | | | speed. | |--------------+---------------------------------------------| | W1 | Enables CONNECT result codes to report DTE | | | speed. If S95=0, then all CARRIER and | | | PROTOCOL extended result codes are enabled. | |--------------+---------------------------------------------| | W2 | Enables CONNECT result codes to report DCE | | | speed. | |--------------+---------------------------------------------| | W3 | Enables CONNECT result codes to report DTE | | | speed. All COMPRESSION and PROTOCOL | | | extended result codes are enabled. | |--------------+---------------------------------------------| | W4 | Enables CONNECT result codes to report DCE | | | speed. All COMPRESSION and PROTOCOL | | | extended result codes are enabled. | +------------------------------------------------------------+ +------------------------------------------------------------+ | LINE SPEED | |------------------------------------------------------------| | Type: | Register | |--------------+---------------------------------------------| | Format | AT [cmds] S37=n [cmds] | |--------------+---------------------------------------------| | Description: | Sets the maximum allowable data exchange | | | rate attempted during handshake process. | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | S37=0 | Connect at speed of last connection | |--------------+---------------------------------------------| | S37=3 | Connect at 300bps. | |--------------+---------------------------------------------| | S37=5 | Connect at 1200bps. | |--------------+---------------------------------------------| | S37=6 | Connect at 2400bps. | |--------------+---------------------------------------------| | S37=7 | Connect at 4800bps. | |--------------+---------------------------------------------| | S37=8 | Connect at 7200bps. | |--------------+---------------------------------------------| | S37=9 | Connect at 9600bps. | |--------------+---------------------------------------------| | S37=10 | Connect at 12Kbps. | |--------------+---------------------------------------------| | S37=11 | Connect at 14.4Kbps. | |--------------+---------------------------------------------| | S37=12 | Connect at 16.8Kbps. | |--------------+---------------------------------------------| | S37=13 | Connect at 19.2Kbps. | |--------------+---------------------------------------------| | S37=14 | Connect at 21.6Kbps. | |--------------+---------------------------------------------| | S37=15 | Connect at 24Kbps. | |--------------+---------------------------------------------| | S37=16 | Connect at 26.4Kbps. | |--------------+---------------------------------------------| | S37=17 | Connect at 28.8Kbps. | |--------------+---------------------------------------------| | S37=18 | Connect at 31.2Kbps. | |--------------+---------------------------------------------| | S37=19 | Connect at 33.6Kbps. | +------------------------------------------------------------+ +------------------------------------------------------------+ | REPORT INFORMATION | |------------------------------------------------------------| | Type: | Immediate | |--------------+---------------------------------------------| | Format: | AT [cmds] In [cmds] | |--------------+---------------------------------------------| | Description: | Displays requested information about the | | | modem. | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | I0 | Reports product identification code. | |--------------+---------------------------------------------| | I1 | Reports modem firmware version. | |--------------+---------------------------------------------| | I2 | Tests and reports ROM checksum. | |--------------+---------------------------------------------| | I3 | Reports device set name. | |--------------+---------------------------------------------| | I4 | Reports OEM response. | |--------------+---------------------------------------------| | I6 | Reports country code. | |--------------+---------------------------------------------| | I7 | Reports board firmware revision. | |--------------+---------------------------------------------| | I8 | Reports modem firmware features. | |--------------+---------------------------------------------| | I10 | Reports board configuration. | |--------------+---------------------------------------------| | I11 | Reports board configuration. | |--------------+---------------------------------------------| | I14 | Reports SAFE device settings. | |--------------+---------------------------------------------| | I20 | Reports Cirrus Logic chipset version. | |--------------+---------------------------------------------| | I21 | Reports Cirrus Logic firmware version. | |--------------+---------------------------------------------| | I22 | Reports Cirrus Logic manufacturer | | | information. | |--------------+---------------------------------------------| | I23 | Reports Cirrus Logic chipset model name. | +------------------------------------------------------------+ +------------------------------------------------------------+ | SLEEP TIMER | |------------------------------------------------------------| | Type: | Register | |--------------+---------------------------------------------| | Format | AT [cmds] S33=n [cmds] | |--------------+---------------------------------------------| | Default: | Unidentified | |--------------+---------------------------------------------| | Range: | 0-90 | |--------------+---------------------------------------------| | Unit: | 1 second | |--------------+---------------------------------------------| | Description: | Sets the maximum duration of DTE and DCE | | | inactivity allowed prior to initiating | | | low-power sleep mode. | +------------------------------------------------------------+ +------------------------------------------------------------+ | TRELLIS CODING | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] &Un [cmds] | |--------------+---------------------------------------------| | Description: | Selects whether the modem will use trellis | | | coding. | |------------------------------------------------------------| | Command | Function | |-----------------------+------------------------------------| | &U0 | Trellis coding enabled. | |-----------------------+------------------------------------| | &U1 | Trellis coding disabled. | +------------------------------------------------------------+