BANKSIA TECHNOLOGY PTY., LTD. ============================= MAC MODEM 288 Card Type Fax, Modem (synchronous/asynchronous) Chip Set Unidentified Maximum Data Rate 28.8Kbps Maximum Fax Rate 14.4Kbps Data Bus External Fax Class Class I & II Data Modulation ITU-T V.21, V.22, V.22bis, V.32, Protocol V.32bis, V.34, V.34bis Fax Modulation ITU-T V.17, V.27ter, V.29 Protocol Error MNP5, MNP10, V.42, V.42bis Correction/Compression +------------------------------------------------------------+ | CONNECTIONS | |------------------------------------------------------------| | Function | Label | Function | Label | |------------------------------------------------------------| | Line out | CN1 | DC power | CN4 | |---------------------------+----------+--------------+------| | Line in | CN2 | Power switch | SW1 | |---------------------------+----------+--------------+------| | RS-232/422 | CN3 | | | +------------------------------------------------------------+ +------------------------------------------------------------+ | DIAGNOSTIC LED(S) | |------------------------------------------------------------| | LED | Color | Status | Condition | |------+-------+--------+------------------------------------| | PWR | Red | On | Power is on | |------+-------+--------+------------------------------------| | PWR | Red | Off | Power is off | |------+-------+--------+------------------------------------| | OH | Red | On | Modem is off-hook | |------+-------+--------+------------------------------------| | OH | Red | Off | Modem is on-hook | |------+-------+--------+------------------------------------| | DTR | Red | On | DTR signal is high | |------+-------+--------+------------------------------------| | DTR | Red | Off | DTR signal is low | |------+-------+--------+------------------------------------| | DCD | Red | On | Carrier signal detected | |------+-------+--------+------------------------------------| | DCD | Red | Off | Carrier signal not detected | |------+-------+--------+------------------------------------| | CTS | Red | On | Modem ready to receive data | |------+-------+--------+------------------------------------| | CTS | Red | Off | Modem not ready to receive data | |------+-------+--------+------------------------------------| | RTS | Red | On | Computer ready to receive data | |------+-------+--------+------------------------------------| | RTS | Red | Off | Computer not ready to receive data | |------+-------+--------+------------------------------------| | RXD | Red | On | Modem is receiving data | |------+-------+--------+------------------------------------| | RXD | Red | Off | Modem is not receiving data | |------+-------+--------+------------------------------------| | TXD | Red | On | Modem is transmitting data | |------+-------+--------+------------------------------------| | TXD | Red | Off | Modem is not transmitting data | |------+-------+--------+------------------------------------| | AA | Red | On | Auto-answer enabled | |------+-------+--------+------------------------------------| | AA | Red | Off | Auto-answer disabled | |------+-------+--------+------------------------------------| | TST | Red | On | Modem in test mode | |------+-------+--------+------------------------------------| | TST | Red | Off | Modem not in test mode | +------------------------------------------------------------+ +------------------------------------------------------------+ | SUPPORTED COMMAND SET | |------------------------------------------------------------| | Basic AT Commands | |------------------------------------------------------------| | AT, '+++', 'Comma', A/ | |------------------------------------------------------------| | A, B, E, H, I, L, M, N, O, P, Q, S, T, V, W, X, Y, Z | |------------------------------------------------------------| | &C, &D, &F, &G, &K, &L, &P, &S, &T, &V, &W, &Y, &Z | |------------------------------------------------------------| | Extended AT Commands | |------------------------------------------------------------| | \A, \B, \G, \K, \L, %C, %L, %Q | |------------------------------------------------------------| | S Registers | |------------------------------------------------------------| | S0, S1, S2, S3, S4, S5, S6, S7, S8, S9, S10, S11, S12, | | S14, S16, S18, S21, S22, S24, S25, S26 | |------------------------------------------------------------| | S29, S30, S31, S32, S33, S36, S37, S38, S39, S46, S48, | | S82, S86, S91, S92, S95 | |------------------------------------------------------------| | Special Commands | |------------------------------------------------------------| | *H, -K, -Q, )M, @M, :E, +MS | |------------------------------------------------------------| | Note: See MHI Help file for full command documentation. | +------------------------------------------------------------+ Proprietary AT Command Set +------------------------------------------------------------+ | AUTOSYNC(TM) | |------------------------------------------------------------| | Format | AT [cmds] S19=n [cmds] | |--------------+---------------------------------------------| | Default: | 0 | |--------------+---------------------------------------------| | Range: | 0-30 | |--------------+---------------------------------------------| | Unit: | Bit-mapped | |--------------+---------------------------------------------| | Description: | Sets options for Hayes AutoSync(TM) functions | |--------------+---------------------------------------------| | Bit | Value | Function | |------+-------+---------------------------------------------| | 0 | i 0 | Not used | |------+-------+---------------------------------------------| | 1 | i 0 | BSC enabled | | | | | | | 1 | HDLC enabled | |------+-------+---------------------------------------------| | 2 | i 0 | HDLC address detection disabled | | | | | | | 1 | HDLC address detection enabled | |------+-------+---------------------------------------------| | 3 | i 0 | NRZI bit encoding enabled | | | | | | | 1 | NZI bit encoding enabled | |------+-------+---------------------------------------------| | 4 | i 0 | Mark idle enabled | | | | | | | 1 | Flag or sync idle enabled | +------------------------------------------------------------+ +------------------------------------------------------------+ | AUTOSYNC ADDRESS CHARACTER | |------------------------------------------------------------| | Type: | Register | |--------------+---------------------------------------------| | Format: | AT [cmds] S20=n [cmds] | |--------------+---------------------------------------------| | Default: | 0 | |--------------+---------------------------------------------| | Range: | 0-255 | |--------------+---------------------------------------------| | Unit: | 1 byte | |--------------+---------------------------------------------| | Description: | Defines the BSC sync character or the HDLC | | | address | +------------------------------------------------------------+ +------------------------------------------------------------+ | AUTO-RETRAIN - AUTO-FALLBACK/FALL-FORWARD | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] %En [cmds] | |--------------+---------------------------------------------| | Description: | Controls auto-retrain mode and | | | fallback/fall-forward | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | i %E0 | Auto-retrain disabled | |--------------+---------------------------------------------| | %E1 | Auto-retrain enabled | |--------------+---------------------------------------------| | %E2 | Auto-fallback/fall-forward enabled | |--------------+---------------------------------------------| | %E3 | Auto-retrain enabled, hang-up when EQM | | | threshold reached | +------------------------------------------------------------+ +------------------------------------------------------------+ | BIT-MAPPED REGISTER S23 | |------------------------------------------------------------| | Format | AT [cmds] S23=n [cmds] | |--------------+---------------------------------------------| | Default: | Unidentified | |--------------+---------------------------------------------| | Range: | 0-191 | |--------------+---------------------------------------------| | Unit: | Bit-mapped | |--------------+---------------------------------------------| | Description: | Grants/denies remote digital loopback, | | | controls DTE rate and parity, and sets | | | guard tone. | |--------------+---------------------------------------------| | Bit | Value | Function | |------+-------+---------------------------------------------| | 0 | 0 | Remote digital loopback denied | | | | | | | 1 | Remote digital loopback allowed | |------+-------+---------------------------------------------| | 3 - | 000 | Sets serial port speed to 0-300bps | | 1 | | | | | 001 | Sets serial port speed to 600bps | | | | | | | 010 | Sets serial port speed to 1200bps | | | | | | | 011 | Sets serial port speed to 2400bps | | | | | | | 100 | Sets serial port speed to 4800bps | | | | | | | 101 | Sets serial port speed to 9600bps | | | | | | | 110 | Sets serial port speed to 19200bps | | | | | | | 111 | Sets serial port speed to 38400bps | |------+-------+---------------------------------------------| | 5, 4 | 00 | Parity even | | | | | | | 01 | Not used | | | | | | | 10 | Parity odd | | | | | | | 11 | Mark or No Parity | |------+-------+---------------------------------------------| | 7, 6 | 00 | Guard tone disabled | | | | | | | 01 | Not used | | | | | | | 10 | Guard tone 1800Hz enabled | +------------------------------------------------------------+ +------------------------------------------------------------+ | BIT-MAPPED REGISTER S27 | |------------------------------------------------------------| | Format | AT [cmds] S27=n [cmds] | |--------------+---------------------------------------------| | Default: | 9 | |--------------+---------------------------------------------| | Range: | 0-127 | |--------------+---------------------------------------------| | Unit: | Bit-mapped | |--------------+---------------------------------------------| | Description: | Selects asynchronous mode, line type, clock | | | source, and ITU-T/Bell modes. | |--------------+---------------------------------------------| | Bit | Value | Function | |------+-------+---------------------------------------------| | 3, | 000 | Asynchronous mode, serial port speed | | 1, 0 | | follows connect speed | | | 001 | | | | | Not used | | | 010 | | | | | Not used | | | 011 | | | | | Not used | | | 100 | | | | | Not used | | | i 101 | | | | | Error correction mode | | | 110 | | | | | Buffered asynchronous mode | | | 111 | | | | | Not used | |------+-------+---------------------------------------------| | 2 | i 0 | Switched line | | | | | | | 1 | Leased line | |------+-------+---------------------------------------------| | 5, 4 | i 00 | Local modem generates transmit clock source | | | | | | | 01 | Local DTE generates transmit clock source | | | | | | | 10 | Remote DCE/DTE generates transmit clock | | | | source | |------+-------+---------------------------------------------| | 6 | i 0 | ITU/T mode | | | | | | | 1 | Bell mode | +------------------------------------------------------------+ +------------------------------------------------------------+ | BIT-MAPPED REGISTER S28 | |------------------------------------------------------------| | Format | AT [cmds] S28=n [cmds] | |--------------+---------------------------------------------| | Default: | 8 | |--------------+---------------------------------------------| | Range: | 0-154 | |--------------+---------------------------------------------| | Unit: | Bit-mapped | |--------------+---------------------------------------------| | Description: | Controls transmit/receive speed, pulse | | | dialing, and MNP link negotiation. | |--------------+---------------------------------------------| | Bit | Value | Function | |------+-------+---------------------------------------------| | 0 | i 0 | Not used | |------+-------+---------------------------------------------| | 1 | i 0 | 75bps transmit, 1200bps receive enabled | | | | | | | 1 | 1200bps transmit, 75bps receive enabled | |------+-------+---------------------------------------------| | 2 | i 0 | Not used | |------+-------+---------------------------------------------| | 4, 3 | 00 | 39ms make/61ms break at 10pps | | | | | | | i 01 | 33ms make/67ms break at 10pps | | | | | | | 10 | 39ms make/61ms break at 20pps | | | | | | | 11 | 33ms make/67ms break at 20pps | |------+-------+---------------------------------------------| | 5 | i 0 | Not used | |------+-------+---------------------------------------------| | 7, 6 | i 00 | Link will be negotiated at highest possible | | | | speed | | | 01 | | | | | Link will be negotiated at 1200bps | | | 10 | | | | | Link will be negotiated at 4800bps | +------------------------------------------------------------+ +------------------------------------------------------------+ | BIT-MAPPED REGISTER S40 | |------------------------------------------------------------| | Format | AT [cmds] S40=n [cmds] | |--------------+---------------------------------------------| | Default: | 105 | |--------------+---------------------------------------------| | Range: | 0-255 | |--------------+---------------------------------------------| | Unit: | Bit-mapped | |--------------+---------------------------------------------| | Description: | Controls power level and break handling; | | | selects MNP extended services, and block | | | size. | |--------------+---------------------------------------------| | Bit | Value | Function | |------+-------+---------------------------------------------| | 1, 0 | 00 | MNP extended services disabled | | | | | | | 01 | MNP extended services enabled | | | | | | | i 10 | MNP extended services enabled without | | | | indicating MNP on the answer detection | | | | phase. | |------+-------+---------------------------------------------| | 2 | i 0 | Power level adjustment enabled | | | | | | | 1 | Power level adjustment disabled | |------+-------+---------------------------------------------| | 5, | 000 | \K0 | | 4, 3 | | | | | 001 | \K1 | | | | | | | i 010 | \K2 | | | | | | | 011 | \K3 | | | | | | | 100 | \K4 | | | | | | | 101 | \K5 | |------+-------+---------------------------------------------| | 7, 6 | 00 | MNP block size is 64 characters | | | | | | | 01 | MNP block size is 128 characters | | | | | | | 10 | MNP block size is 192 characters | | | | | | | i 11 | MNP block size is 256 characters | +------------------------------------------------------------+ +------------------------------------------------------------+ | BIT-MAPPED REGISTER S41 | |------------------------------------------------------------| | Format | AT [cmds] S41=n [cmds] | |--------------+---------------------------------------------| | Default: | 131 | |--------------+---------------------------------------------| | Range: | 0-219 | |--------------+---------------------------------------------| | Unit: | Bit-mapped | |--------------+---------------------------------------------| | Description: | Selects compression, | | | auto-retrain/auto-fallback/fall-forward, | | | flow control, MNP mode and V.22/22bis | | | fallback. | |--------------+---------------------------------------------| | Bit | Value | Function | |------+-------+---------------------------------------------| | 1 - | 00 | Data compression disabled | | 0 | | | | | 01 | MNP5 enabled | | | | | | | 10 | V.42bis enabled | | | | | | | i 11 | MNP5 and V.42bis enabled | |------+-------+---------------------------------------------| | 6, 2 | i 00 | Auto-retrain disabled | | | | | | | 01 | Auto-retrain enabled | | | | | | | 10 | Auto-fallback/fall-forward enabled | |------+-------+---------------------------------------------| | 3 | i 0 | Flow control disabled | | | | | | | 1 | Flow control enabled | |------+-------+---------------------------------------------| | 4 | i 0 | Stream mode for MNP | | | | | | | 1 | Block mode for MNP | |------+-------+---------------------------------------------| | 5 | i 0 | Not used | |------+-------+---------------------------------------------| | 7 | 0 | MNP at 2400 and 1200bps disabled | | | | | | | i 1 | MNP at 2400 and 1200bps enabled | +------------------------------------------------------------+ +------------------------------------------------------------+ | BIT-MAPPED REGISTER S201 | |------------------------------------------------------------| | Format: | AT [cmds] S201=n [cmds] | |--------------------+---------------------------------------| | Default: | 58 | |--------------------+---------------------------------------| | Range: | 0-62 | |--------------------+---------------------------------------| | Description: | Controls power level and compromise | | | equalizer | |------------------------------------------------------------| | Bit | Value | Function | |-----------+------------+-----------------------------------| | 4 - 0 | i 00000 | Initial power level -26dBm | | | | | | | 00001 | Initial power level -30dBm | | | | | | | 00010 | Initial power level -10dBm | | | | | | | ... | ... | | | | | | | 01010 | Initial power level -10dBm | | | | | | | 01011 | Initial power level -11dBm | | | | | | | ...to... | ...to... | | | | | | | 11111 | Initial power level -31dBm | |------------------------------------------------------------| | 5 | 0 | Equalizer disabled | | | | | | | i 1 | Equalizer enabled | +------------------------------------------------------------+ +------------------------------------------------------------+ | BREAK TYPE | |------------------------------------------------------------| | Type: | Configuration | |---------------------+--------------------------------------| | Format: | AT [cmds] \Kn [cmds] | |---------------------+--------------------------------------| | Description: | Configures action of break signal | |------------------------------------------------------------| | Command | Break from DTE | Break | Break from | | | during | received from | DTE during | | | Normal/Reliable | remote modem | Direct mode | | | mode | during normal | | | | | mode | | |-----------+-----------------+---------------+--------------| | \K0 | Online command | Buffers | Online | | | mode enabled, | cleared, | command mode | | | send no break | break sent to | enabled, | | | to remote modem | DTE | break sent | | | | | to remote | | | | | modem | |-----------+-----------------+---------------+--------------| | \K1 | Buffers | Buffers | Send break | | | cleared, sends | cleared, | to remote | | | break to remote | break sent to | modem | | | modem | DTE | immediately | |-----------+-----------------+---------------+--------------| | \K2 | Online command | Break sent | Online | | | mode enabled, | immediately | command mode | | | send no break | to DTE | enabled, | | | to remote modem | | break sent | | | | | to remote | | | | | modem | |-----------+-----------------+---------------+--------------| | \K3 | Send break to | Break sent | Send break | | | remote modem | immediately | to remote | | | immediately | to DTE | modem | | | | | immediately | |-----------+-----------------+---------------+--------------| | \K4 | Online command | Send break | Online | | | mode enabled, | with | command mode | | | send no break | transmitted | enabled, | | | to remote modem | data | break sent | | | | | to remote | | | | | modem | |-----------+-----------------+---------------+--------------| | i \K5 | Send break with | Send break | Send break | | | transmitted | with | to remote | | | data | transmitted | modem | | | | data | immediately | +------------------------------------------------------------+ +------------------------------------------------------------+ | COMMUNICATIONS MODE | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] &Mn [cmds] | |--------------+---------------------------------------------| | Description: | Selects communications mode | |--------------+---------------------------------------------| | Command | Mode | |--------------+---------------------------------------------| | i &M0 | Asynchronous mode | |--------------+---------------------------------------------| | &M1 | Not used | |--------------+---------------------------------------------| | &M2 | Not used | |--------------+---------------------------------------------| | &M3 | Not used | +------------------------------------------------------------+ +------------------------------------------------------------+ | COMMUNICATIONS MODE | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] &Qn [cmds] | |--------------+---------------------------------------------| | Description: | Selects communications mode options | |--------------+---------------------------------------------| | Command | Mode | |--------------+---------------------------------------------| | i &Q0 | Asynchronous mode, serial port speed | | | follows connect speed. | |--------------+---------------------------------------------| | &Q1 | Not used | |--------------+---------------------------------------------| | &Q2 | Not used | |--------------+---------------------------------------------| | &Q3 | Not used | |--------------+---------------------------------------------| | &Q4 | Not used | |--------------+---------------------------------------------| | &Q5 | Error correction mode | |--------------+---------------------------------------------| | &Q6 | Buffered asynchronous mode | +------------------------------------------------------------+ +------------------------------------------------------------+ | DIAL | |------------------------------------------------------------| | Type: | Immediate | |--------------+---------------------------------------------| | Format: | AT [cmds] D<#> [cmds] | |--------------+---------------------------------------------| | Description: | Dials telephone number according to any | | | modifiers included in the string | |--------------+---------------------------------------------| | Note: | Any combination of modifiers can be used to | | | produce the desired dial functions in | | | sequence. | |--------------+---------------------------------------------| | Modifier | Function | |--------------+---------------------------------------------| | J | MNP10 link negotiation enabled | |--------------+---------------------------------------------| | K | Power level adjustment enabled during MNP10 | |--------------+---------------------------------------------| | L | Re-dial last number | |--------------+---------------------------------------------| | P | Pulse dialing enabled | |--------------+---------------------------------------------| | R | Accepted, but not acted upon | |--------------+---------------------------------------------| | T | Tone dialing enabled | |--------------+---------------------------------------------| | W | Dialing resumed following dial tone | | | detection | |--------------+---------------------------------------------| | $ | Waits for prompt tone for amount of time | | | specified by the S7 register. | |--------------+---------------------------------------------| | ; | Modem returned to command state after | | | dialing | |--------------+---------------------------------------------| | ^ | Toggle calling tone enabled/disabled | |--------------+---------------------------------------------| | ! | Modem commanded to go off-hook for amount | | | of time specified in S29 register | |--------------+---------------------------------------------| | @ | Wait for quiet answer | |--------------+---------------------------------------------| | , | Dialing paused for amount of time specified | | | in S8 register | +------------------------------------------------------------+ +------------------------------------------------------------+ | DCE LINE SPEED | |------------------------------------------------------------| | Type: | Register | |--------------+---------------------------------------------| | Format | AT [cmds] S37=n [cmds] | |--------------+---------------------------------------------| | Description: | Sets the maximum allowable data exchange | | | rate | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | i S37=0 | Automode connection | |--------------+---------------------------------------------| | S37=1 | 300bps | |--------------+---------------------------------------------| | S37=2 | 300bps | |--------------+---------------------------------------------| | S37=3 | 300bps | |--------------+---------------------------------------------| | S37=5 | 1200bps | |--------------+---------------------------------------------| | S37=6 | 2400bps | |--------------+---------------------------------------------| | S37=7 | V.23 mode | |--------------+---------------------------------------------| | S37=8 | 4800bps | |--------------+---------------------------------------------| | S37=9 | 9600bps | |--------------+---------------------------------------------| | S37=10 | 12.0Kbps | |--------------+---------------------------------------------| | S37=11 | 14.4Kbps | |--------------+---------------------------------------------| | S37=12 | 7200bps | |--------------+---------------------------------------------| | S37=15 | 14.4Kbps | |--------------+---------------------------------------------| | S37=16 | V.FC 16.8Kbps | |--------------+---------------------------------------------| | S37=17 | V.FC 19.2Kbps | |--------------+---------------------------------------------| | S37=18 | V.FC 21.6Kbps | +------------------------------------------------------------+ +------------------------------------------------------------+ | REPORT INFORMATION | |------------------------------------------------------------| | Type: | Immediate | |--------------+---------------------------------------------| | Format: | AT [cmds] In [cmds] | |--------------+---------------------------------------------| | Description: | Displays information requested | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | I0 | Reports product code | |--------------+---------------------------------------------| | I1 | Reports ROM checksum | |--------------+---------------------------------------------| | I2 | Tests and reports ROM checksum | |--------------+---------------------------------------------| | I3 | Reports firmware revision, model identity | |--------------+---------------------------------------------| | I4 | Reports model type | +------------------------------------------------------------+