ACTIONTEC ELECTRONICS, INC. =========================== FME288 Card Type Fax, Modem (synchronous/asynchronous), Network Interface Card Chip Set Unidentified I/O Options Ethernet 10BaseT connector NIC Type Ethernet Network Transfer Rate 10Mbps Maximum Modem Rate 28.8Kbps Maximum Fax Rate 14.4Kbps Data Bus PCMCIA Type II Fax Class Class I & II Data Modulation Bell 103/212A Protocol ITU-T V.21, V.22, V.22bis, V.23, V.25bis, V.32, V.32bis, V.34 Fax Modulation ITU-T V.17, V.21CH2, V.27ter, V.29 Protocol Error MNP5, MNP10, V.42, V.42bis Correction/Compression Topology Star Wiring Type Unshielded twisted pair Boot ROM Not available V2286 Proprietary AT Command Set +------------------------------------------------------------+ | AUTO-RETRAIN - AUTO-FALLBACK/FALL-FORWARD | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] %En [cmds] | |--------------+---------------------------------------------| | Description: | Controls auto-retrain mode and | | | fallback/fall-forward | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | %E0 | Auto-retrain disabled | |--------------+---------------------------------------------| | %E1 | Auto-retrain enabled | |--------------+---------------------------------------------| | %E2 | Auto-fallback/fall-forward enabled | +------------------------------------------------------------+ +------------------------------------------------------------+ | BIT MAPPED REGISTERS | |------------------------------------------------------------| | Register | Default | |----------------------------+-------------------------------| | S28 | Unidentified | +------------------------------------------------------------+ +------------------------------------------------------------+ | BIT-MAPPED REGISTER S14 | |------------------------------------------------------------| | Format: | AT [cmds] S14=n [cmds] | |--------------+---------------------------------------------| | Default: | 138 | |--------------+---------------------------------------------| | Range: | 0-174 | |--------------+---------------------------------------------| | Unit: | Bit-mapped | |--------------+---------------------------------------------| | Description: | Controls echo, result codes and display, | | | dial mode, and answer/originate mode. | |--------------+---------------------------------------------| | Bit | Value | Function | |------+-------+---------------------------------------------| | 0 | i 0 | Not used | |------+-------+---------------------------------------------| | 1 | 0 | Command echo disabled | | | | | | | i 1 | Command echo enabled | |------+-------+---------------------------------------------| | 2 | i 0 | Result codes enabled | | | | | | | 1 | Result codes disabled | |------+-------+---------------------------------------------| | 3 | 0 | Display result codes in numeric format | | | | | | | i 1 | Display result codes in verbose format | |------+-------+---------------------------------------------| | 4 | i 0 | Not used | |------+-------+---------------------------------------------| | 5 | i 0 | Tone dial enabled | | | | | | | 1 | Pulse dial enabled | |------+-------+---------------------------------------------| | 6 | i 0 | Not used | |------+-------+---------------------------------------------| | 7 | 0 | Answer mode enabled | | | | | | | i 1 | Originate mode enabled | +------------------------------------------------------------+ +------------------------------------------------------------+ | BIT-MAPPED REGISTER S21 | |------------------------------------------------------------| | Format | AT [cmds] S21=n [cmds] | |--------------+---------------------------------------------| | Default: | 4 | |--------------+---------------------------------------------| | Range: | 0-253 | |--------------+---------------------------------------------| | Unit: | Bit-mapped | |--------------+---------------------------------------------| | Description: | Selects jack type, CTS/DCD/DSR signals, low | | | DTR action, and the long space disconnect | | | function | |--------------+---------------------------------------------| | Bit | Value | Function | |------+-------+---------------------------------------------| | 0 | i 0 | Selects RJ-11, RJ-41S, or RJ45S jack | | | | | | | 1 | Selects RJ-12 or RJ-13 jack | |------+-------+---------------------------------------------| | 1 | i 0 | Not used | |------+-------+---------------------------------------------| | 2 | 0 | CTS forced high | | | | | | | i 1 | CTS follows RTS | |------+-------+---------------------------------------------| | 4, 3 | i 00 | DTR signal ignored | | | | | | | 01 | Modem goes to command mode on low DTR | | | | | | | 10 | Modem disconnects on low DTR; Auto-Answer | | | | is disabled | | | 11 | | | | | Modem is initialized on low DTR | |------+-------+---------------------------------------------| | 5 | i 0 | DCD forced high | | | | | | | 1 | DCD normal | |------+-------+---------------------------------------------| | 6 | i 0 | DSR forced high | | | | | | | 1 | DSR normal | |------+-------+---------------------------------------------| | 7 | i 0 | Long space disconnect function disabled | | | | | | | 1 | Long space disconnect function enabled | +------------------------------------------------------------+ +------------------------------------------------------------+ | BIT-MAPPED REGISTER S22 | |------------------------------------------------------------| | Format | AT [cmds] S22=n [cmds] | |--------------+---------------------------------------------| | Default: | 117 | |--------------+---------------------------------------------| | Range: | 0-127 | |--------------+---------------------------------------------| | Unit: | Bit-mapped | |--------------+---------------------------------------------| | Description: | Controls speaker volume and controls, and | | | limits results codes. | |--------------+---------------------------------------------| | Bit | Value | Function | |------+-------+---------------------------------------------| | 1, 0 | 00 | Volume off | | | | | | | i 01 | Low level volume | | | | | | | 10 | Medium level volume | | | | | | | 11 | High level volume | |------+-------+---------------------------------------------| | 3, 2 | 00 | Speaker off | | | | | | | i 01 | Speaker off on carrier | | | | | | | 10 | Speaker always on | | | | | | | 11 | Speaker on during handshake | |------+-------+---------------------------------------------| | 6 - | 000 | Basic result codes only enabled | | 4 | | | | | 100 | Basic and connection speed result codes | | | | enabled | | | 101 | | | | | Basic and connection speed result codes and | | | 110 | dialtone detection enabled | | | | | | | i 111 | All result codes except dialtone detection | | | | enabled | | | | | | | | All result codes enabled | +------------------------------------------------------------+ +------------------------------------------------------------+ | BIT-MAPPED REGISTER S23 | |------------------------------------------------------------| | Format | AT [cmds] S23=n [cmds] | |--------------+---------------------------------------------| | Default: | 55 | |--------------+---------------------------------------------| | Range: | 0-189 | |--------------+---------------------------------------------| | Unit: | Bit-mapped | |--------------+---------------------------------------------| | Description: | Grants/denies remote digital loopback, | | | controls DTE rate and parity, and sets | | | guard tone | |--------------+---------------------------------------------| | Bit | Value | Function | |------+-------+---------------------------------------------| | 0 | 0 | Remote digital loopback denied | | | | | | | i 1 | Remote digital loopback allowed | |------+-------+---------------------------------------------| | 3 - | 000 | Sets serial port speed to 0-300bps | | 1 | | | | | 001 | Sets serial port speed to 600bps | | | | | | | 010 | Sets serial port speed to 1200bps | | | | | | | i 011 | Sets serial port speed to 2400bps | | | | | | | 100 | Sets serial port speed to 4800bps | | | | | | | 101 | Sets serial port speed to 9600bps | | | | | | | 110 | Sets serial port speed to 19200bps | |------+-------+---------------------------------------------| | 5, 4 | 00 | Parity even | | | | | | | 01 | Not used | | | | | | | 10 | Parity odd | | | | | | | i 11 | No parity | |------+-------+---------------------------------------------| | 7, 6 | i 00 | Guard tone disabled | | | | | | | 01 | Guard tone disabled | | | | | | | 10 | Guard tone 1800Hz enabled | +------------------------------------------------------------+ +------------------------------------------------------------+ | BIT-MAPPED REGISTER S27 | |------------------------------------------------------------| | Format | AT [cmds] S27=n [cmds] | |--------------+---------------------------------------------| | Default: | 74 | |--------------+---------------------------------------------| | Range: | 0-111 | |--------------+---------------------------------------------| | Unit: | Bit-mapped | |--------------+---------------------------------------------| | Description: | Selects synchronous/asynchronous mode, line | | | type, clock source, and ITU-T/Bell modes. | |--------------+---------------------------------------------| | Bit | Value | Function | |------+-------+---------------------------------------------| | 3, | 000 | Asynchronous mode, serial port speed | | 1, 0 | | follows connect speed | | | 001 | | | | | Asynchronous off-line command mode and | | | 010 | synchronous connect mode | | | | | | | 011 | Asynchronous off-line command mode; modem | | | | auto-dials first number in directory, then | | | 100 | synchronous connect mode | | | | | | | 101 | Asynchronous off-line command mode on low | | | | DTR, synchronous connect mode on high DTR | | | 111 | | | | | Auto-synchronous mode | | | | | | | | Error correction mode | | | | | | | | Buffered asynchronous mode | |------+-------+---------------------------------------------| | 2 | 0 | Switched line | | | | | | | 1 | Leased line | |------+-------+---------------------------------------------| | 5, 4 | 00 | Local modem generates transmit clock source | | | | | | | 01 | Local DTE generates transmit clock source | | | | | | | 10 | Remote DCE/DTE generates transmit clock | | | | source | |------+-------+---------------------------------------------| | 6 | 0 | ITU/T mode | | | | | | | 1 | Bell mode | +------------------------------------------------------------+ +------------------------------------------------------------+ | BIT-MAPPED REGISTER S31 | |------------------------------------------------------------| | Format: | AT [cmds] S31=n [cmds] | |----------------+-------------------------------------------| | Default: | 2 | |----------------+-------------------------------------------| | Range: | 0-2 | |----------------+-------------------------------------------| | Description: | Select automode | |------------------------------------------------------------| | Bit | Value | Function | |----------+-------+-----------------------------------------| | 0 | i 0 | Not used | |----------+-------+-----------------------------------------| | 1 | 0 | Auto-mode detection disabled | | | | | | | i 1 | In originate mode, handshake begins at | | | | line speed designated by the S37 | | | | register. Modem can shift to a slower | | | | speed if necessary. | | | | | | | | In answer mode, handshake attempted | | | | with the following protocols in order - | | | | V.32bis, V.32, V.22bis, V.22 or Bell | | | | 212, V.21, and Bell 103 | +------------------------------------------------------------+ +------------------------------------------------------------+ | BIT-MAPPED REGISTER S40 | |------------------------------------------------------------| | Format | AT [cmds] S40=n [cmds] | |--------------+---------------------------------------------| | Default: | 105 | |--------------+---------------------------------------------| | Range: | 0-255 | |--------------+---------------------------------------------| | Unit: | Bit-mapped | |--------------+---------------------------------------------| | Description: | Controls MNP extended services, fallback, | | | power level, break handling, and block | | | size. | |--------------+---------------------------------------------| | Bit | Value | Function | |------+-------+---------------------------------------------| | 0 | 0 | MNP extended services disabled | | | | | | | 1 | MNP extended services enabled | |------+-------+---------------------------------------------| | 1 | 0 | MNP10 at 2400 and 1200bps disabled | | | | | | | 1 | MNP10 at 2400 and 1200bps enabled | |------+-------+---------------------------------------------| | 2 | i 0 | Power level adjustment enabled | | | | | | | 1 | Power level adjustment disabled | |------+-------+---------------------------------------------| | 5, | 000 | \K0 | | 4, 3 | | | | | 001 | \K1 | | | | | | | 010 | \K2 | | | | | | | 011 | \K3 | | | | | | | 100 | \K4 | | | | | | | i 101 | \K5 | |------+-------+---------------------------------------------| | 7, 6 | 00 | MNP block size is 64 characters | | | | | | | i 01 | MNP block size is 128 characters | | | | | | | 10 | MNP block size is 192 characters | | | | | | | 11 | MNP block size is 256 characters | +------------------------------------------------------------+ +------------------------------------------------------------+ | BIT-MAPPED REGISTER S41 | |------------------------------------------------------------| | Format | AT [cmds] S41=n [cmds] | |--------------+---------------------------------------------| | Default: | Unidentified | |--------------+---------------------------------------------| | Range: | 0-31 | |--------------+---------------------------------------------| | Unit: | Bit-mapped | |--------------+---------------------------------------------| | Description: | Selects compression, auto-retrain, flow | | | control, and MNP mode. | |--------------+---------------------------------------------| | Bit | Value | Function | |------+-------+---------------------------------------------| | 1 - | 00 | Data compression disabled | | 0 | | | | | 01 | MNP5 enabled | | | | | | | 10 | V.42bis enabled | | | | | | | i 11 | MNP5 and V.42bis enabled | |------+-------+---------------------------------------------| | 6, 2 | i 00 | Auto-retrain disabled | | | | | | | 01 | Auto-retrain enabled | | | | | | | 10 | Auto-retrain and auto-fallback enabled | |------+-------+---------------------------------------------| | 3 | i 0 | Flow control disabled | | | | | | | 1 | Flow control enabled | |------+-------+---------------------------------------------| | 4 | i 0 | Stream mode for MNP | | | | | | | 1 | Block mode for MNP | +------------------------------------------------------------+ +------------------------------------------------------------+ | BIT-MAPPED REGISTER S201 | |------------------------------------------------------------| | Format: | AT [cmds] S201=n [cmds] | |--------------------+---------------------------------------| | Default: | 32 | |--------------------+---------------------------------------| | Range: | 0-62 | |--------------------+---------------------------------------| | Description: | Controls power level and compromise | | | equalizer | |------------------------------------------------------------| | Bit | Value | Function | |-----------+------------+-----------------------------------| | 4 - 0 | 00000 | Initial power level -26dBm | | | | | | | 00001 | Initial power level -30dBm | | | | | | | 00010 | Initial power level -10dBm | | | | | | | ... | ... | | | | | | | 01010 | Initial power level -10dBm | | | | | | | 01011 | Initial power level -11dBm | | | | | | | ...to... | ...to... | | | | | | | 11110 | Initial power level -30dBm | |------------------------------------------------------------| | 5 | 0 | Equalizer disabled | | | | | | | 1 | Equalizer enabled | +------------------------------------------------------------+ +------------------------------------------------------------+ | BREAK SEND | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] \Bn [cmds] | |--------------+---------------------------------------------| | Default: | 3 | |--------------+---------------------------------------------| | Range: | 1-9 | |--------------+---------------------------------------------| | Unit: | .1 second | |--------------+---------------------------------------------| | Description: | Sends break to modem | +------------------------------------------------------------+ +------------------------------------------------------------+ | BREAK TYPE | |------------------------------------------------------------| | Type: | Configuration | |---------------------+--------------------------------------| | Format: | AT [cmds] \Kn [cmds] | |---------------------+--------------------------------------| | Description: | Configures action of break signal | |------------------------------------------------------------| | Command | Break from | Modem receives | Break received | | | DTE | \B | from remote | | | | | modem | |-----------+--------------+----------------+----------------| | \K0 | Online | Break sent to | Buffers | | | command mode | remote modem | cleared, break | | | enabled, | and buffers | sent to DTE | | | send no | cleared | | | | break to | | | | | remote modem | | | |-----------+--------------+----------------+----------------| | \K1 | Break sent | Break sent to | Buffers | | | to remote | remote modem | cleared, break | | | modem and | and buffers | sent to DTE | | | buffers | cleared | | | | cleared | | | |-----------+--------------+----------------+----------------| | \K2 | Online | Send break to | Break sent | | | command mode | remote modem | immediately to | | | enabled, | immediately | DTE | | | send no | | | | | break to | | | | | remote modem | | | |-----------+--------------+----------------+----------------| | \K3 | Send break | Send break to | Break sent | | | to remote | remote modem | immediately to | | | modem | immediately | DTE | | | immediately | | | |-----------+--------------+----------------+----------------| | \K4 | Online | Send break | Break sent | | | command mode | with | with received | | | enabled, | transmitted | data to the | | | send no | data | DTE | | | break to | | | | | remote modem | | | |-----------+--------------+----------------+----------------| | i \K5 | Send break | Send break | Break sent | | | with | with | with received | | | transmitted | transmitted | data to the | | | data | data | DTE | +------------------------------------------------------------+ +------------------------------------------------------------+ | COMPRESSION | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] %Cn [cmds] | |--------------+---------------------------------------------| | Description: | Selects data compression | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | %C0 | Data compression disabled | |--------------+---------------------------------------------| | %C1 | MNP5 enabled | |--------------+---------------------------------------------| | %C2 | V.42bis enabled | |--------------+---------------------------------------------| | %C3 | MNP5 and V.42bis enabled | +------------------------------------------------------------+ +------------------------------------------------------------+ | CONNECT MODE | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] \Nn [cmds] | |--------------+---------------------------------------------| | Description: | Controls the type of connection the modem | | | will operate in | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | \N0 | Normal mode enabled | |--------------+---------------------------------------------| | \N1 | Direct mode enabled | |--------------+---------------------------------------------| | \N2 | Reliable mode enabled | |--------------+---------------------------------------------| | \N3 | Auto-reliable mode enabled | |--------------+---------------------------------------------| | \N4 | V.42 reliable mode enabled | |--------------+---------------------------------------------| | \N5 | MNP reliable mode enabled | +------------------------------------------------------------+ +------------------------------------------------------------+ | DIAL | |------------------------------------------------------------| | Type: | Immediate | |--------------+---------------------------------------------| | Format: | AT [cmds] D<#> [cmds] | |--------------+---------------------------------------------| | Description: | Dials telephone number according to any | | | modifiers included in the string | |--------------+---------------------------------------------| | Note: | Any combination of modifiers can be used to | | | produce the desired dial functions in | | | sequence. | |--------------+---------------------------------------------| | Modifier | Function | |--------------+---------------------------------------------| | J | Link will be negotiated at highest possible | | | speed | |--------------+---------------------------------------------| | K | Power level adjustment enabled | |--------------+---------------------------------------------| | L | Re-dial last number | |--------------+---------------------------------------------| | P | Pulse dialing enabled | |--------------+---------------------------------------------| | R | Accepted, but not acted upon | |--------------+---------------------------------------------| | S=n | Dial stored telephone number n | |--------------+---------------------------------------------| | T | Tone dialing enabled | |--------------+---------------------------------------------| | W | Dialing resumed following dial tone | | | detection | |--------------+---------------------------------------------| | ! | Modem commanded to go off-hook for | | | specified time before returning on-hook | |--------------+---------------------------------------------| | @ | Wait for quiet answer | |--------------+---------------------------------------------| | , | Dialing paused for amount of time specified | | | in S8 register | |--------------+---------------------------------------------| | ; | Modem returned to command state after | | | dialing | |--------------+---------------------------------------------| | ^ | Calling tone disabled | |--------------+---------------------------------------------| | > | Generate a grounding pulse on ground output | +------------------------------------------------------------+ +------------------------------------------------------------+ | FLOW CONTROL | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] \Gn [cmds] | |--------------+---------------------------------------------| | Description: | Selects modem port flow control | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | i \G0 | Flow control disabled | |--------------+---------------------------------------------| | \G1 | Flow control enabled | +------------------------------------------------------------+ +------------------------------------------------------------+ | FLOW CONTROL | |------------------------------------------------------------| | Type: | Read-only Register | |--------------+---------------------------------------------| | Format | AT [cmds] S39? [cmds] | |--------------+---------------------------------------------| | Description: | Displays the current flow control | |--------------+---------------------------------------------| | Value | Meaning | |--------------+---------------------------------------------| | 0 | Flow control disabled | |--------------+---------------------------------------------| | i 3 | RTS/CTS flow control enabled | |--------------+---------------------------------------------| | 4 | XON/XOFF flow control enabled | |--------------+---------------------------------------------| | 5 | Transparent XON/XOFF flow control enabled | |--------------+---------------------------------------------| | 6 | Both XON/XOFF and RTS/CTS flow control | | | enabled | +------------------------------------------------------------+ +------------------------------------------------------------+ | FLOW CONTROL CHARACTER - XOFF | |------------------------------------------------------------| | Type: | Register | |--------------+---------------------------------------------| | Format: | AT [cmds] S33=n [cmds] | |--------------+---------------------------------------------| | Default: | 19 | |--------------+---------------------------------------------| | Range: | 0-255 | |--------------+---------------------------------------------| | Unit: | ASCII | |--------------+---------------------------------------------| | Description: | Sets the character used to represent XOFF | +------------------------------------------------------------+ +------------------------------------------------------------+ | FLOW CONTROL CHARACTER - XON | |------------------------------------------------------------| | Type: | Register | |--------------+---------------------------------------------| | Format: | AT [cmds] S32=n [cmds] | |--------------+---------------------------------------------| | Default: | 17 | |--------------+---------------------------------------------| | Range: | 0-255 | |--------------+---------------------------------------------| | Unit: | ASCII | |--------------+---------------------------------------------| | Description: | Sets the character used to represent XON | +------------------------------------------------------------+ +------------------------------------------------------------+ | LOCK SERIAL PORT | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] \Jn [cmds] | |--------------+---------------------------------------------| | Description: | Sets operation of serial port speed | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | i \J0 | Serial speed locked | |--------------+---------------------------------------------| | \J1 | Serial speed follows connect speed | +------------------------------------------------------------+ +------------------------------------------------------------+ | MAXIMUM BLOCK SIZE FOR TRANSMISSION | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] \An [cmds] | |--------------+---------------------------------------------| | Description: | Sets the maximum transmittable block size | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | \A0 | MNP block size is 64 characters | |--------------+---------------------------------------------| | i \A1 | MNP block size is 128 characters | |--------------+---------------------------------------------| | \A2 | MNP block size is 192 characters | |--------------+---------------------------------------------| | \A3 | MNP block size is 256 characters | +------------------------------------------------------------+ +------------------------------------------------------------+ | LINE SIGNAL LEVEL | |------------------------------------------------------------| | Type: | Immediate | |--------------+---------------------------------------------| | Format: | AT [cmds] %L [cmds] | |--------------+---------------------------------------------| | Default: | Unidentified | |--------------+---------------------------------------------| | Range: | 9-43 | |--------------+---------------------------------------------| | Unit: | -1 dBm | |--------------+---------------------------------------------| | Description: | Returns a value which indicates the | | | received line signal level | +------------------------------------------------------------+ +------------------------------------------------------------+ | LINE SIGNAL QUALITY | |------------------------------------------------------------| | Type: | Immediate | |--------------+---------------------------------------------| | Format: | AT [cmds] %Q [cmds] | |--------------+---------------------------------------------| | Description: | Returns a value which indicates line signal | | | quality | +------------------------------------------------------------+ +------------------------------------------------------------+ | MNP - EXTENDED SERVICES | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] -Kn [cmds] | |--------------+---------------------------------------------| | Description: | Selects MNP extended services | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | -K0 | MNP extended services disabled | |--------------+---------------------------------------------| | i -K1 | MNP extended services enabled | +------------------------------------------------------------+ +------------------------------------------------------------+ | MNP - STREAM/BLOCK MODE | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] \Ln [cmds] | |--------------+---------------------------------------------| | Description: | Selects the transfer mode for MNP link | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | i \L0 | Stream mode for MNP enabled | |--------------+---------------------------------------------| | \L1 | Block mode for MNP enabled | +------------------------------------------------------------+ +------------------------------------------------------------+ | MNP10 - FALLBACK | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] -Qn [cmds] | |--------------+---------------------------------------------| | Description: | Allows MNP10 to fall back to speeds slower | | | than 4800bps | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | -Q0 | MNP10 at 2400 and 1200bps disabled | |--------------+---------------------------------------------| | -Q1 | MNP10 at 2400 and 1200bps enabled | +------------------------------------------------------------+ +------------------------------------------------------------+ | MNP10 - LINK NEGOTIATION | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] *Hn [cmds] | |--------------+---------------------------------------------| | Description: | Sets the speed at which MNP10 link | | | negotiation will occur | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | i *H0 | Link will be negotiated at highest possible | | | speed | |--------------+---------------------------------------------| | *H1 | Link will be negotiated at 1200bps | |--------------+---------------------------------------------| | *H2 | Link will be negotiated at 4800bps | +------------------------------------------------------------+ +------------------------------------------------------------+ | MNP10 - POWER LEVEL ADJUST | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] )Mn [cmds] | |--------------+---------------------------------------------| | Description: | Controls automatic transmit power level | | | adjustment during MNP 10 link negotiation | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | i )M0 | Power level adjustment disabled | |--------------+---------------------------------------------| | )M1 | Power level adjustment enabled | +------------------------------------------------------------+ +------------------------------------------------------------+ | REPORT INFORMATION | |------------------------------------------------------------| | Type: | Immediate | |--------------+---------------------------------------------| | Format: | AT [cmds] In [cmds] | |--------------+---------------------------------------------| | Description: | Displays information requested | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | I0 | Reports product code | |--------------+---------------------------------------------| | I1 | Reports OK | |--------------+---------------------------------------------| | I6 | Reports modem data pump model and internal | | | code revision | +------------------------------------------------------------+ +------------------------------------------------------------+ | TEST MODES | |------------------------------------------------------------| | Type: | Register | |--------------+---------------------------------------------| | Format: | AT [cmds] S16=n [cmds] | |--------------+---------------------------------------------| | Default: | 0 | |--------------+---------------------------------------------| | Range: | 0-125 | |--------------+---------------------------------------------| | Unit: | Bit-mapped | |--------------+---------------------------------------------| | Description: | Controls loopback tests: analog, digital, | | | remote digital, and self tests | |--------------+---------------------------------------------| | Bit | Value | Function | |------+-------+---------------------------------------------| | 0 | i 0 | Local analog loopback not in progress | | | | | | | 1 | Local analog loopback in progress | |------+-------+---------------------------------------------| | 1 | i 0 | Not used | |------+-------+---------------------------------------------| | 2 | i 0 | Local digital loopback not in progress | | | | | | | 1 | Local digital loopback in progress | |------+-------+---------------------------------------------| | 3 | i 0 | Modem not in remote digital loopback | | | | | | | 1 | Remote digital loopback in progress | |------+-------+---------------------------------------------| | 4 | i 0 | Remote digital loopback not requested | | | | | | | 1 | Remote digital loopback requested | |------+-------+---------------------------------------------| | 5 | i 0 | Remote digital loopback w/ self-test not in | | | | progress | | | 1 | | | | | Remote digital loopback w/ self-test in | | | | progress | |------+-------+---------------------------------------------| | 6 | i 0 | Local analog loopback w/ self-test not in | | | | progress | | | 1 | | | | | Local analog loopback w/ self-test in | | | | progress | +------------------------------------------------------------+ +------------------------------------------------------------+ | TEST MODE - PTT | |------------------------------------------------------------| | Type: | Immediate | |--------------+---------------------------------------------| | Format: | AT [cmds] %TTn [cmds] | |--------------+---------------------------------------------| | Description: | Send PTT test signals for a line tests | +------------------------------------------------------------+ +------------------------------------------------------------+ | TRANSMISSION LEVEL - FAX | |------------------------------------------------------------| | Type: | Register | |--------------+---------------------------------------------| | Format: | AT [cmds] S92=n [cmds] | |--------------+---------------------------------------------| | Default: | 10 | |--------------+---------------------------------------------| | Range: | 0-15 | |--------------+---------------------------------------------| | Unit: | -1 dBm | |--------------+---------------------------------------------| | Description: | Sets the signal level for transmission | | | while in fax mode | +------------------------------------------------------------+ +------------------------------------------------------------+ | TRANSMISSION LEVEL - LEASED-LINE | |------------------------------------------------------------| | Type: | Register | |--------------+---------------------------------------------| | Format: | AT [cmds] S99=n [cmds] | |--------------+---------------------------------------------| | Default: | 10 | |--------------+---------------------------------------------| | Range: | 0-15 | |--------------+---------------------------------------------| | Unit: | -1 dBm | |--------------+---------------------------------------------| | Description: | Sets the signal level for transmission over | | | leased-lines | +------------------------------------------------------------+ +------------------------------------------------------------+ | TRANSMISSION LEVEL - PSTN | |------------------------------------------------------------| | Type | Register | |-------------+----------------------------------------------| | Format | AT [cmds] S91=n [cmds] | |-------------+----------------------------------------------| | Default | 10 | |-------------+----------------------------------------------| | Range | 0-15 | |-------------+----------------------------------------------| | Unit | -1 dBm | |-------------+----------------------------------------------| | Description | Sets the signal level for transmission over | | | PSTN | +------------------------------------------------------------+ V.25bis COMMAND SET +------------------------------------------------------------+ | CONNECT INCOMING CALLS | |------------------------------------------------------------| | Type: | Immediate | |--------------+---------------------------------------------| | Format: | CIC | |--------------+---------------------------------------------| | Description: | Instructs the modem to answer an incoming | | | call; if no call is currently incoming, a | | | result of INV will be returned. | +------------------------------------------------------------+ +------------------------------------------------------------+ | CALL REQUESTED NUMBER AND IDENTIFICATION | |------------------------------------------------------------| | Type: | Immediate | |--------------+---------------------------------------------| | Format: | CRI<#> | |--------------+---------------------------------------------| | Description: | Adds dial string and identifier into | | | memory. | +------------------------------------------------------------+ +------------------------------------------------------------+ | CALL REQUESTED NUMBER | |------------------------------------------------------------| | Type: | Immediate | |--------------+---------------------------------------------| | Format: | CRN<#> | |--------------+---------------------------------------------| | Description: | Dials the number given; it will ignore | | | spaces and hyphens in the string; if the | | | string is more than fifty characters long, | | | a result of INV will be returned. | +------------------------------------------------------------+ +------------------------------------------------------------+ | CALL REQUEST WITH ADDRESS | |------------------------------------------------------------| | Type: | Immediate | |--------------+---------------------------------------------| | Format: | CRSn | |--------------+---------------------------------------------| | Description: | Dials the number stored in memory register | | | n | +------------------------------------------------------------+ +------------------------------------------------------------+ | DISREGARD INCOMING CALL | |------------------------------------------------------------| | Type: | Immediate | |--------------+---------------------------------------------| | Format: | DIC | |--------------+---------------------------------------------| | Description: | Instructs the modem to ignore the incoming | | | call, if the modem is set to automatically | | | answer; if no call is currently incoming, a | | | result of INV will be returned. | +------------------------------------------------------------+ +------------------------------------------------------------+ | PROGRAM NUMBER | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | PRNn or PRN | |--------------+---------------------------------------------| | Description: | Stores a phone number in memory address n. | | | If the second form of this command is | | | issued (i.e. with no string to store), it | | | will clear memory address n. | +------------------------------------------------------------+ +------------------------------------------------------------+ | REQUEST LIST OF DELAYED NUMBERS | |------------------------------------------------------------| | Type: | Immediate | |--------------+---------------------------------------------| | Format: | RLD | |--------------+---------------------------------------------| | Description: | Requests the list of delayed numbers from | | | the modem; this is a list of numbers that | | | the modem attempted to call and failed, and | | | is not allowed to call again until a set | | | amount of time has elapsed; this is usually | | | to prevent repeated dialing of a number | | | (which could indicate an attempted security | | | breach). | +------------------------------------------------------------+ +------------------------------------------------------------+ | REQUEST LIST OF FORBIDDEN NUMBERS | |------------------------------------------------------------| | Type: | Immediate | |--------------+---------------------------------------------| | Format: | RLF | |--------------+---------------------------------------------| | Description: | Requests the list of forbidden numbers from | | | the modem; the modem is unable to dial | | | numbers on this list until its power has | | | been cycled. | +------------------------------------------------------------+ +------------------------------------------------------------+ | REQUEST LISTED NUMBERS | |------------------------------------------------------------| | Type: | Immediate | |--------------+---------------------------------------------| | Format: | RLI | |--------------+---------------------------------------------| | Description: | The modem will return VAL message. | +------------------------------------------------------------+ V.25BIS COMMAND SET RESULT CODES +------------------------------------------------------------+ | CALL FAILURE INDICATOR | |------------------------------------------------------------| | Type: | Response | |-------------------+----------------------------------------| | Format: | CFIxx | |-------------------+----------------------------------------| | Description: | Indicates that the attempt to connect | | | failed | |------------------------------------------------------------| | Response | Name | Description | |------------+-----------+-----------------------------------| | CFIAB | Abort | The call was aborted because | | | | either no dialtone was detected | | | | or a character was received from | | | | the host computer. | |------------+-----------+-----------------------------------| | CFICB | DCE Busy | An incoming call was detected | | | | after the dialing command was | | | | issued. | |------------+-----------+-----------------------------------| | CFIET | Engaged | A busy signal was detected. | | | Tone | | |------------+-----------+-----------------------------------| | CFIFC | Forbidden | The number given is on the | | | Call | forbidden list. | |------------+-----------+-----------------------------------| | CFINS | Not | The memory address given did not | | | Stored | contain a valid telephone number. | |------------+-----------+-----------------------------------| | CFINT | No Tone | The remote party did not issue a | | | | response tone. | |------------+-----------+-----------------------------------| | CFIRT | Ring Tone | A responding tone was detected, | | | | but the call timed out before it | | | | was completed. | +------------------------------------------------------------+ +------------------------------------------------------------+ | CONNECTION | |------------------------------------------------------------| | Type: | Response | |--------------+---------------------------------------------| | Format: | CNX | |--------------+---------------------------------------------| | Description: | A connection has been successfully | | | established | +------------------------------------------------------------+ +------------------------------------------------------------+ | DELAYED CALL | |------------------------------------------------------------| | Type: | Response | |--------------+---------------------------------------------| | Format: | DLCn | |--------------+---------------------------------------------| | Description: | The telephone number given is on the | | | delayed call list; the call cannot be | | | completed until n minutes elapse. | +------------------------------------------------------------+ +------------------------------------------------------------+ | INCOMING CALL | |------------------------------------------------------------| | Type: | Response | |--------------+---------------------------------------------| | Format: | INC | |--------------+---------------------------------------------| | Description: | An incoming call has been detected | +------------------------------------------------------------+ +------------------------------------------------------------+ | INVALID | |------------------------------------------------------------| | Type: | Response | |--------------+---------------------------------------------| | Format: | INV | |--------------+---------------------------------------------| | Description: | The modem was issued an improper command | +------------------------------------------------------------+ +------------------------------------------------------------+ | VALID | |------------------------------------------------------------| | Type: | Response | |--------------+---------------------------------------------| | Format: | VAL | |--------------+---------------------------------------------| | Description: | The command issued is valid and is being | | | executed |