PURE DATA, LTD.
===============

   PDI8023-16FL

   NIC Type      Ethernet                                         
   Transfer Rate 10Mbps                                           
   Data Bus      16-bit ISA                                       
   Topology      Star                                             
   Wiring Type   62.5/125 m m Fiber optic cable (e.g. Belden      
                 227412)                                          
   Boot ROM      Available                                        

<gopher://bitreich.org/I/th99/n/P-R/40496-1.png>
   

   +------------------------------------------------------------+
   |                SOFTWARE CONFIGURATION RESET                |
   |------------------------------------------------------------|
   |             Setting              |           E1            |
   |----------------------------------+-------------------------|
   |>>       |    Normal operation    |    Pins 2 & 3 closed    |
   |---------+------------------------+-------------------------|
   |         |         Reset          |    Pins 1 & 2 closed    |
   |------------------------------------------------------------|
   | Note:Many of the options are configured using the setup    |
   | utility provided with the card. To reset those             |
   | configurations to the factory defaults, move E1 to the     |
   | Reset position (pins 1 & 2 closed) and apply power for a   |
   | few seconds. Always make sure that you turn off the power  |
   | to the computer before you change any jumpers.             |
   +------------------------------------------------------------+

   +------------------------------------------------------------+
   |                      CARD I/D NUMBER                       |
   |------------------------------------------------------------|
   |    Number    |    E2A     |   E2B    |   E2C    |   E2D    |
   |--------------+------------+----------+----------+----------|
   |>>     |  1   |    Open    |   Open   |   Open   |  Closed  |
   |-------+------+------------+----------+----------+----------|
   |       |  2   |    Open    |   Open   |  Closed  |   Open   |
   |-------+------+------------+----------+----------+----------|
   |       |  3   |    Open    |  Closed  |   Open   |   Open   |
   |-------+------+------------+----------+----------+----------|
   |       |  4   |   Closed   |   Open   |   Open   |   Open   |
   |------------------------------------------------------------|
   |   Note:Up to four cards can be installed into a system at  |
   |   the same time. If more than one card is installed each   |
   |   one must have a seperate card I/D number.                |
   +------------------------------------------------------------+

   +------------------------------------------------------------+
   |  EXTENDED TRANSMIT TIMEOUT AND SIGNAL QUALITY ERROR (SQE)  |
   |                            TEST                            |
   |------------------------------------------------------------|
   |   Timeout    |    SQE     |   E6A    |   E6B    |   E6C    |
   |--------------+------------+----------+----------+----------|
   |   Enabled    |  Enabled   |  Closed  |   Open   |   Open   |
   |--------------+------------+----------+----------+----------|
   |   Disabled   |  Disabled  |   Open   |  Closed  |   Open   |
   |--------------+------------+----------+----------+----------|
   |   Enabled    |  Disabled  |   Open   |   Open   |  Closed  |
   |------------------------------------------------------------|
   | Note:With extended transmit timeout enabled, if the card   |
   | is transmitting for an extented amount of time the         |
   | transmission will be interrupted and continued after a     |
   | preset time. This keeps the card from dominating the       |
   | network.                                                   |
   |                                                            |
   | Signal Quality Error (SQE) is a test of the collision      |
   | circuitry and path.                                        |
   |                                                            |
   | E6 is located on the PIM.                                  |
   +------------------------------------------------------------+

   +------------------------------------------------------------+
   |                      LOOP BACK ENABLE                      |
   |------------------------------------------------------------|
   |         Setting          |               E7                |
   |--------------------------+---------------------------------|
   |>>       |    Disabled    |        Pins 1 & 2 closed        |
   |---------+----------------+---------------------------------|
   |         |    Enabled     |        Pins 2 & 3 closed        |
   |------------------------------------------------------------|
   | Note:A loop back connector is used with diagnostic         |
   | software to trouble-shoot the card.                        |
   |                                                            |
   | E7 is located on the PIM.                                  |
   +------------------------------------------------------------+

   +------------------------------------------------------------+
   |                FACTORY CONFIGURED SETTINGS                 |
   |------------------------------------------------------------|
   |            Jumper            |           Setting           |
   |------------------------------+-----------------------------|
   |             E5A              |           Closed            |
   |------------------------------+-----------------------------|
   |             E5B              |            Open             |
   |------------------------------+-----------------------------|
   |             E5C              |            Open             |
   +------------------------------------------------------------+

   +------------------------------------------------------------+
   |                     DIAGNOSTIC LED(S)                      |
   |------------------------------------------------------------|
   | LED  | Color | Status |             Condition              |
   |------+-------+--------+------------------------------------|
   | LED1 | Green |   On   |     Data is being transmitted      |
   |------+-------+--------+------------------------------------|
   | LED1 | Green |  Off   |   Data is not being transmitted    |
   |------+-------+--------+------------------------------------|
   | LED2 | Amber |   On   |       Data is being received       |
   |------+-------+--------+------------------------------------|
   | LED2 | Amber |  Off   |     Data is not being received     |
   |------+-------+--------+------------------------------------|
   | LED3 | Amber |   On   |     Network connection is good     |
   |------+-------+--------+------------------------------------|
   | LED3 | Amber |  Off   |    Network connection is broken    |
   |------+-------+--------+------------------------------------|
   | LED4 |  Red  |   On   |    Card is transmitting for an     |
   |      |       |        |           extended time            |
   |------+-------+--------+------------------------------------|
   | LED4 |  Red  |  Off   |          Normal operation          |
   |------+-------+--------+------------------------------------|
   | LED5 |  Red  |   On   |   Collision detected on network    |
   |------+-------+--------+------------------------------------|
   | LED5 |  Red  |  Off   |          Normal operation          |
   +------------------------------------------------------------+