PURE DATA, LTD.
===============

   PDI8023-16CAT

   NIC Type         Ethernet                                      
   Transfer Rate    10Mbps                                        
   Data Bus         16-bit ISA                                    
   Topology         Star                                          
                                                                  
                    Linear bus                                    
   Wiring Type      Unshielded twisted pair                       
                                                                  
                    RG58A/U 50ohm coaxial                         
                                                                  
                    AUI transceiver via DB-15 port                
   Boot ROM         Available                                     

<gopher://bitreich.org/I/th99/n/P-R/40494-1.png>
   

   +------------------------------------------------------------+
   |                SOFTWARE CONFIGURATION RESET                |
   |------------------------------------------------------------|
   |             Setting             |            E1            |
   |---------------------------------+--------------------------|
   |>>      |    Normal operation    |    Pins 2 & 3 closed     |
   |--------+------------------------+--------------------------|
   |        |         Reset          |    Pins 1 & 2 closed     |
   |------------------------------------------------------------|
   | Note:Many of the options are configured using the setup    |
   | utility provided with the card. To reset those             |
   | configurations to the factory defaults, move E1 to the     |
   | Reset position (pins 1 & 2 closed) and apply power for a   |
   | few seconds. Always make sure that you turn off the power  |
   | to the computer before you change any jumpers.             |
   +------------------------------------------------------------+

   +------------------------------------------------------------+
   |                      CARD I/D NUMBER                       |
   |------------------------------------------------------------|
   |   Number    |     E2A     |   E2B    |   E2C    |   E2D    |
   |-------------+-------------+----------+----------+----------|
   |>>    |  1   |    Open     |   Open   |   Open   |  Closed  |
   |------+------+-------------+----------+----------+----------|
   |      |  2   |    Open     |   Open   |  Closed  |   Open   |
   |------+------+-------------+----------+----------+----------|
   |      |  3   |    Open     |  Closed  |   Open   |   Open   |
   |------+------+-------------+----------+----------+----------|
   |      |  4   |   Closed    |   Open   |   Open   |   Open   |
   |------------------------------------------------------------|
   | Note:Up to four cards can be installed into a system at    |
   | the same time.                                             |
   |                                                            |
   | If more than one card is installed each one must have a    |
   | seperate card I/D number.                                  |
   +------------------------------------------------------------+

   +------------------------------------------------------------+
   |                    LINK INTEGRITY TEST                     |
   |------------------------------------------------------------|
   |            Setting            |             E3             |
   |-------------------------------+----------------------------|
   |>>         |      Enabled      |     Pins 1 & 2 closed      |
   |-----------+-------------------+----------------------------|
   |           |     Disabled      |     Pins 2 & 3 closed      |
   |------------------------------------------------------------|
   | Note:The link integrity test is only valid when the cable  |
   | type is unshielded twisted pair.                           |
   +------------------------------------------------------------+

   +------------------------------------------------------------+
   |                         CABLE TYPE                         |
   |------------------------------------------------------------|
   |       Type        |  E5A   |  E5B   |  E5C   |  Isolation  |
   |                   |        |        |        | Transformer |
   |                   |        |        |        |  Location   |
   |-------------------+--------+--------+--------+-------------|
   |>>  |   RG58A/U    |  Open  | Closed |  Open  |     T3      |
   |    |    50ohm     |        |        |        |             |
   |    |   coaxial    |        |        |        |             |
   |----+--------------+--------+--------+--------+-------------|
   |    |  Unshielded  |  Open  |  Open  | Closed |     N/A     |
   |    | twisted pair |        |        |        |             |
   |----+--------------+--------+--------+--------+-------------|
   |    |     AUI      | Closed |  Open  |  Open  |     T2      |
   |    | transceiver  |        |        |        |             |
   |    |  via DB-15   |        |        |        |             |
   |    |     port     |        |        |        |             |
   |------------------------------------------------------------|
   | Note:If you leave E5B closed you can select the cable type |
   | through the software setup utility included with the card. |
   | However, you must still move the Isolation transformer to  |
   | the appropriate socket.                                    |
   +------------------------------------------------------------+

   +------------------------------------------------------------+
   |                       SEGMENT LENGTH                       |
   |------------------------------------------------------------|
   |         Maximum Length         |            JP7            |
   |--------------------------------+---------------------------|
   |>>         |     185 meters     |     Pins 2 & 3 closed     |
   |-----------+--------------------+---------------------------|
   |           |     300 meters     |     Pins 1 & 2 closed     |
   |------------------------------------------------------------|
   |   Note:Segment length is the total length of cable between |
   |   the two farthest cards on the segment. Each card on the  |
   |   segment must have this option set the same.              |
   +------------------------------------------------------------+

<gopher://bitreich.org/I/th99/n/P-R/40494-2.png>
   

   +------------------------------------------------------------+
   |                     DIAGNOSTIC LED(S)                      |
   |------------------------------------------------------------|
   | LED  | Color | Status |             Condition              |
   |------+-------+--------+------------------------------------|
   | LED1 | Green |   On   |    Data is being transmitted or    |
   |      |       |        |              received              |
   |------+-------+--------+------------------------------------|
   | LED1 | Green |  Off   |  Data is not being transmitted or  |
   |      |       |        |              received              |
   |------+-------+--------+------------------------------------|
   | LED2 |  Red  |   On   |   Card is being accessed by host   |
   |      |       |        |              computer              |
   |------+-------+--------+------------------------------------|
   | LED2 |  Red  |  Off   | Card is not being accessed by host |
   |      |       |        |              computer              |
   +------------------------------------------------------------+