Posts by esden@chaos.social
(DIR) Post #AzkhkpLwJL0XUT0IpE by esden@chaos.social
0 likes, 0 repeats
Now that the UI board is fully assembled we can test it! It is also time to update the bootloader and firmware! All we need is some jumper wires and a USB cable. And the verdict is… NO SMOKE! #hamradio #kitradio #mchf
(DIR) Post #AzkhkqDT6JpGAU33GC by esden@chaos.social
0 likes, 0 repeats
Now that we have the UI board assembled and tested it is turn to start on the RF board. Let's do the simple stuff first and solder on some connectors. Power jack, KEY and ACC, the BNC for the antenna, and an off the shelf balun. I have to order the temperature sensor chip that would be added in this step to for some extra TCXO temperature compensation stuff. #hamradio #kitradio #mchf
(DIR) Post #Azkhkr8Xg7Tn1UkdDk by esden@chaos.social
0 likes, 0 repeats
I have mounted the first few hand wound devices on the board. A balun, a choke and two transformers. They are part of the power amplifier circuit. (still getting the hang of hand winding and soldering these in…) #hamradio #kitradio #mchf
(DIR) Post #Azkhks9dtVxCBCH1Zg by esden@chaos.social
0 likes, 0 repeats
As a side-quest. To make my life a bit easier. I have taken the mcHF design files and imported them to KiCad. You can find them on my GitHub. https://github.com/esden/mchf-kicad and yes they open in KiCanvas!!! ;) UI Board: https://kicanvas.org/?github=https://github.com/esden/mcHF-kicad/tree/main/v0.6.3/ui RF Board: https://kicanvas.org/?github=https://github.com/esden/mcHF-kicad/tree/main/v0.6.3/rf #hamradio #kitradio #mchf #kicad
(DIR) Post #AzkhktFLpm79ZBx66y by esden@chaos.social
0 likes, 0 repeats
Now I need to wind all the inductors for the Lowpass filters. Each filter consists of 3 inductors. I started with the 80m band toroids. 24, 27 and 24 turns each. #hamradio #kitradio #mchf #kicad
(DIR) Post #Azkhku56jLVy9iAQme by esden@chaos.social
0 likes, 0 repeats
Here we go! All the filter inductors are wound and soldered in! I tried my best to do an even and clean job... I did check them with the low cost LCR meter I have and they seem to be in the ballpark of the specified values. #hamradio #kitradio #mchf
(DIR) Post #AzkhkvEiR6nJjnfcOm by esden@chaos.social
0 likes, 0 repeats
Last hand built items on the RF board are the SWR/PWR meter transformers. I have to admit, getting those coax windings was a major pain in the back side… I am pretty sure the bend radius is “illegal”. I have the feeling that the board was not originally designed with those coax windings in mind. But as far as I can tell things are soldered and connected where they should and the two toroids are wound in their opposite directions as the documentation describes! 😅 #hamradio #kitradio #mchf
(DIR) Post #AzkhkwCGrgQuiVXBE8 by esden@chaos.social
0 likes, 0 repeats
After mounting one stray relay on the back side of the board, we can finally assemble the parts that go onto the "front side" of the RF board. Another funky balun, 3 relays, some connectors and a neon bulb to protect from the antenna zapping us. :D ⚡️ #hamradio #kitradio #mchf
(DIR) Post #AzkhkxDN54uJsD3Za4 by esden@chaos.social
0 likes, 0 repeats
To install the TO-220 PA MOSFETs and LDOs it is necessary to partially assemble the RF board into the case. It is really hard to get the nuts onto the chassis bolts so I decided to solder them onto the tabs. (these are the moments I praise having a JBC iron!) #hamradio #kitradio #mchf
(DIR) Post #AzkhkxrQg8wxsRnZ1E by esden@chaos.social
0 likes, 0 repeats
Remember how at the beginning we were missing a resistor for the electret microphone? It arrived, so let's solder it in before we assemble the whole radio into the enclosure. #hamradio #kitradio #mchf
(DIR) Post #AzkhkyibURU6XMg1tw by esden@chaos.social
0 likes, 0 repeats
First thing for the case is to screw in and solder the wire to the speaker. #hamradio #kitradio #mchf
(DIR) Post #AzkhkzaUG6aPETt3tA by esden@chaos.social
0 likes, 0 repeats
Next is the RF board we spent so much time on, followed by an RF shield. The enclosure comes with an RF shield but it needs a bunch of modifications. So instead of doing that I designed my own RF shield and ordered it from Send Cut Send! It worked out great. You can find the design on my GitHub. ;) https://github.com/esden/mchf-rf-shield #hamradio #kitradio #mchf
(DIR) Post #Azkhl0YOfMVaEHuuGm by esden@chaos.social
0 likes, 0 repeats
Now the UI board can be mounted on top of that. Let's finally remove that pesky protective film from the LCD display! #hamradio #kitradio #mchf
(DIR) Post #Azkhl1CSGQYEEWethw by esden@chaos.social
0 likes, 0 repeats
The front panel has some silicone covers for the buttons. But oddly enough these are not mats that fit the hole pattern. One has to clip the buttons apart and then insert into the button holes. It makes the assembly a bit awkward because the buttons love to fly out of position. #hamradio #kitradio #mchf
(DIR) Post #Azkhl1q9soJIDfEbaq by esden@chaos.social
0 likes, 0 repeats
And here we go! We have a fully assembled mcHF QRP radio! There is more work to do, but let's sit back and enjoy the view l for a little bit! :D #hamradio #kitradio #mchf
(DIR) Post #Azkhl2OBqHX3vD9mdc by esden@chaos.social
0 likes, 0 repeats
I have to wait for a dummy load and a few other bits and bobs to arrive before I can calibrate the radio and try to go on air with it. In the mean time I am trying to get familiar with the controls and while doing that I managed to receive some SSB on 40m! 🎉📻 #hamradio #kitradio #mchf
(DIR) Post #Azkhl3AkviNeLpsZKy by esden@chaos.social
0 likes, 0 repeats
Another little thing to do on the radio: I now got some silicone thermal pads for the TO-220s, so I have to take the radio apart and put them in. While I am at it I am also adding the optional TCXO temperature sensor. The instructions recommend to couple the oscillator and the sensor with some copper tape. #hamradio #kitradio #mchf
(DIR) Post #Azkhl4JIhQoFscsuIK by esden@chaos.social
0 likes, 0 repeats
While I had the radio open, I also decided to decrease the rattle and tack down the inductors using some hot glue. I am aware it is getting warm inside the radio so that might just create a huge mess, but I feel it is worth a try. If that does not work out I will remove it (it should be relatively easy using IPA) and replace it with silicone. We will see™️ :D #hamradio #kitradio #mchf
(DIR) Post #B0qgAORM0SHYOMsHOy by esden@chaos.social
0 likes, 0 repeats
Not the same magnitude but also true for other electronic products. I can confirm :) People underestimate the amount of time that goes into BOM and vendor selection and negotiation of pricing where possible. https://mastodon.social/@mntmn/115651741718808237
(DIR) Post #B0qgAPqCnXksjjVdmC by esden@chaos.social
0 likes, 0 repeats
@mntmn funnily enough I tend to underestimate how much effort it is every time I face bring up of a new project 😅