SUPER 3 SOFTWARE SUPR3IRD is a run chip for all IRD units. This chip functions in stand alone decoders except the service messages do not work. SUPER3 is the run chip for all stand alone units. SUPRLOAD is the load chip which loads the id numbers into ram SUPRUTIL is the utility reader chip used to read both the monthly authorizations and the working keys. The working key can only be read in 010x units! DEALER KITS include all 4 of the above chips. LOCATIONS FOR THE SUPRLOAD -------------------------- The Monthly keys are located at 0100 and 0163. (Version 2.x Software) The ID# first four bytes are located at 0235. The Seed keys are located at 2000. The Wizard codes are located at 0640. EXAMPLE: ------- 2000: 00 00 00 00 00 00 00(00) 11 11 11 11 11 11 11 (00) 22 22 22 22 22 22 22(00) 33 33 33 33 33 33 33 (00) Seven bytes then a 00, seven more then 00, seven more then 00, then seven more then 00. These Keys are secure once loaded into Ram they are encrypted using DES Trap 18.. The installed Primary and Backup keys are for test purposes only and it is recommended that you install your own working keys. It is up to the user to install his own Primary and Backup clone numbers. You can install a set of backup keys at location 2E00. These keys can be used in the event the Primary (master) clone goes down. The Backup id is stored at 2E20 first 4 bytes. If the master clone goes down switch in the backup ID. The box will not have audio. Therefore switch to 0 key mode (wizard mode), With a valid working key use the box until you lose the audio. This will occur AFTER THE CHANGE IN MONTHS CODES. Now switch to clone mode and things should be back to normal. SUPRUTIL: -------- Press setup and 5 to clear all U-7 information. This is used only when you have a lost FF (5th byte of ID#) or the software is trying to be installed in 010x boxes. The software can also be used in 010x boxes without losing the seed keys only if the box is cloned to itself by using a cloning chip such as Keys-R-US. or By using Functions 8 and 9 of this chip.. Which ever you wish. Press setup and 6 to read monthly keys. Press setup and 7 to read working keys. (010x units) Press setup and 8 to read keys in a 010x box Press setup and 9 to load keys in a 010x box SUPR3IRD and SUPER3 ------------------- Pressing setup and 9 will display options available. Pressing number 5 will put the box into the 0 key mode. Pressing number 6 and the unit uses the clone number. That is installed in ram. The message bar at the bottom of the screen will tell you which mode is currently operating. Pressing number 7 allows you to tell the unit how many banks to search when using the 0 key mode. Pressing 8 allows the entering of the working keys into the banks of information stored in the unit, it is used only in the 0 key mode. WIZARD CODES In the Zero key mode the working key must be entered. This code is entered slightly different than the wizard. The first 4 8 digit sequences are entered the same. There is an additional screen to enter the service ID which is 4 digits the next digit can be a 0 to 8 (for the bank number) the last 3 digits are 0. You will then be prompted on how many banks to search. if you have 1 bank installed enter 0100 then 'Enter'. If you had 3 banks enter 0300 then 'Enter'. The setup 0 screen shows which bank is being used. USING THE BACKUP KEYS: At any time you can switch to the backup set of keys by pressing setup up and then pressing the left hand arrow 10 times. The screen will flash and the unit switches to the backup keys. You will have to stay in the ZERO key (WIZARD) mode until the unit takes a hit then you can switch to the clone again at the BEGINNING OF THE NEXT MONTH. You CAN NOT GO BACK to the primary clone except by using the Loader chip again. IMPORTANT THIS SOFTWARE WILL TAKE HITS ONLY ON AUTHORIZED CHANNELS IT REJECTS INFORMATION COMING FROM UNAUTHORIZED CHANNELS. CERTAIN ELECTRONIC COUNTER MEASURES ARE SENDING BAD INFO TO UNITS IF THEY ARE TUNED TO AN UNAUTHORIZED CHANNEL. Use of this file is for EDUCATIONAL, EXPERIMENTAL and TEST purposes only! These chips are not intended or meant for unauthorized reception of satalite signals. Purchaser assumes all responsibility for legal use of these chips. .... ... ...-....1200 N81N ......................... ... ...-....1200 N81N .... Downloaded From P-80 International Information Systems 304-744-2253